ECO mode TOYOTA AVALON 2011 XX30 / 3.G Navigation Manual

11
No.NameFunctionPage
6“SETUP” button
Push this button to display the “Setup”
screen.
You can change the language from this
screen. (See “ Selecting a language”
on page 207.)
22, 100, 206,
211, 212, 215, 224, 262, 270
7“DISP” buttonPush this button to display the “Display”
screen.31
8Zoom out buttonTouch this button to reduce the map
scale.41
9“  Off”
Touch this button to obtain a broader
view. Some of the buttons on the
screen are not displayed. They are dis-
played again by touching “On ”.
220
10“Mark”
Touch th is button to register the current
position or the cursor position as a
memory point.
34
11“Route”Touch this button to change the route.82, 84
12“Show on Map”
Touch this button to browse information
about guidance route, to set the Points
of Interest to be displayed on the
screen, or to record the route.
90, 94, 95, 97
13Zoom in buttonTouch this button to magnify the map
scale.41
14Foot print map
buttonTouch this button to display the foot print
map and the building information.42
15
Screen
configuration
buttonTouch this button to change the screen
mode.39
16
Distance and
time to
destinationDisplays the distance, the estimated
travel time to the destination, and the
estimated arrival time at the destination.
81
17XM NavTraffic
markThis mark is displayed when XM  Nav-
Traffic information is received.96
18
“GPS” mark
(Global
Positioning
System)Whenever the vehicle is receiving sig-
nals from the GPS, this mark is dis-
played.
276

BASIC FUNCTIONS
26
Vehicles with smart key system —
When the “ENGINE START STOP” switch
is in ACCESSORY or IGNITION ON
mode, the initial screen will be displayed
and the system will begin operating.
Vehicles without smart key system —
When the engine switch is in the “ACC” or
“ON” position, the initial screen will be
displayed and the system will begin oper-
ating.
CAUTION
When the vehicle is stopped with the
engine running, always apply the
parking brake for safety.
After a few seconds, the “CAUTION”
screen will be displayed.
After about 5 seconds, the “CAUTION”
screen automatically switches to the map
screen. When the “MAP/VOICE” button
is also pushed, the map screen is dis-
played.
While the “CAUTION” screen is displayed,
the “DEST” or “SETUP” button cannot be
operated. And if the “Calendar” button on
the “Information” screen is touched, the
screen will change back to the “CAUTION”
screen. In about 5 seconds, or when the
“MAP/VOICE” button is pushed or the
“Show Map” is touched, the “CAUTION”
screen will change to the map screen.
Initial screen

BASIC FUNCTIONS
31
You can adjust the contrast and brightness
of the screen. You can also turn the display
off, and change the screen to either day or
night mode.
Contrast and brightness adjust-
ment
The contrast and brightness of the screen
can be adjusted depending on the bright-
ness of your surroundings. You can also
turn the display off.
1. Push the “DISP” button.
2. Touch the desired button to adjust
contrast and brightness.
“Contrast” “
+”: Strengthens the contrast
of the screen.
“Contrast” “
–”: Weakens the contrast of
the screen.
“Brightness” “
+”: Brightens the screen.
“Brightness” “
–”: Darkens the screen.
3. After adjusting the screen, touch
“OK”.
The screen goes off when “Screen Off” is
touched. To turn the display screen back
on, push the “DISP” button again, or push
the “DEST” or another screen mode but-
ton.
INFORMATION
When you do not touch any button on
the “Display” screen for 20 seconds,
the previous screen will be displayed.
Screen adjustment

TELEPHONE AND INFORMATION
129

Reconnecting the Bluetooth

phone
Vehicles with smart key system —
If the Bluetooth phone is
disconnected with a poor reception
from the Bluetooth network when the
“ENGINE START STOP” switch is in
ACCESSORY or IGNITION ON mode,
the system automatically reconnects
the Bluetooth  phone. In this case, the
connection result is not displayed.
Vehicles without smart key system —
If the Bluetooth phone is
disconnected with a poor reception
from the Bluetooth network when the
engine switch is in the “ACC” or “ON”
position the system automatically
reconnects the Bluetooth phone. In
this case, the connection result is not
displayed.
If the Bluetooth is disconnected on pur-
pose such as you turned your cellular
phone off, this does not happen. Recon-
nect it by the following methods.
Select the Bluetooth phone again.
Enter the Bluetooth phone.After you enter the Bluetooth
 phone,
you can call by using handsfree sys-
tem. You can call using the 6 methods
described below.
By dial
You can call by inputting the phone
number.
This cannot be operated while driving.
1. Push the “INFO/PHONE” button.
You can also push
of the steering
wheel to display the “Phone” screen.
2. Touch “Phone”.
— Call on the Bluetooth
phone

AUDIO SYSTEM
151
Turn the knob clockwise to step up the
station band or counterclockwise to
step down.
Your radio automatically changes to stereo
reception when a stereo broadcast is re-
ceived. “ST” appears on the screen. If the
signal becomes weak, the radio reduces
the amount of channel separation to pre-
vent the weak signal from creating noise.
If the signal becomes extremely weak, the
radio switches from stereo to mono recep-
tion. In this case, “ST” disappears from the
screen.
(b) Presetting a station
1. Tune in the desired station.
2. Touch one of the touchscreen but-
tons (1 — 6) you want and hold it until
a beep is heard. This sets the station to
the touchscreen button and the fre-
quency appears on the touchscreen
button.
Each radio mode (AM, FM1 or FM2) can
store up to 6 stations. To change the pre-
set station to a different one, follow the
same procedure.
The preset station memory is cancelled
when the power source is interrupted by
the battery disconnection or a blown fuse.

AUDIO SYSTEM
152
(c) Selecting a station
Tune in the desired station using one of the
following methods.
Preset tuning: Touch the touch−screen
button (1 — 6) for the station you want.
The touch−screen button is highlighted
and the station frequency appears on the
screen.
Seek tuning: Push the “
” or “” but-
ton of “SEEK/TRACK” . The radio will be-
gin seeking up or down for a station of the
nearest frequency and will stop on recep-
tion. Each time you push the button, the
stations will be searched automatically
one after another.
To scan all the frequencies: Touch
“SCAN” on the screen briefly. “SCAN” ap-
pears on the screen. The radio will find the
next station and stay there for a few se-
conds, and then scan again. To select a
station, touch “SCAN” again.
To scan the preset stations: Touch
“SCAN” on the screen for longer than a
second. “P. SCAN” appears on the screen.
The radio will tune in the next preset sta-
tion, stay there for a few seconds, and then
move to the next preset station. To select
a station, touch “SCAN” again.(d) Radio Data System
Your audio system is equipped with Radio
Data Systems (RDS). RDS mode pro-
vides you to receive text messages from
radio stations that utilize RDS transmit-
ters.
When RDS is on, the radio can
— only select stations of a particular pro-
gram type,
— display messages from radio stations,
— search for a stronger signal station.
RDS features are available for use only on
FM stations which broadcast RDS infor-
mation.

AUDIO SYSTEM
178 
Reconnecting the portable player
Vehicles with smart key system —
If the portable player is disconnected with
a poor reception from the Bluetooth  net-
work when the “ENGINE START STOP”
switch is in ACCESSORY or IGNITION
ON mode, the system automatically re-
connects the portable player . In this case,
the connection result is not displayed.
Vehicles without smart key system —
If the portable player is disconnected with
a poor reception from the Bluetooth  net-
work when the engine switch is in the
“ACC” or “ON” position, the system auto-
matically reconnects the portable player.
In this case, the connection result is not
displayed.
If the Bluetooth is disconnected on pur-
pose such as you turned your portable
player off, this does not happen.
Reconnect it by the following method.
Select the portable player again.
Enter the portable player. (b) Playing a Bluetooth
audio
Playing and pausing a Bluetooth 
audio
Push the “AUX” button or push the
“AUDIO” button to display this screen
and touch the “BT” tab if the
Bluetooth  audio player is alreay
connected.
Touch
and the music will start playing.
Touch
and the music will pause.
Touch
and the music will start playing
again.
Depending on the portable player that is
connected to the system, the music may
start playing when touching
while it is
paused. On the other h and, the music may
pause when touching
while it is play-
ing.

AUDIO SYSTEM
191
FM
Fading and drifting stations — Generally,
the effective range of FM is about 25 miles
(40 km). Once outside this range, you may
notice fading and drifting, which increase
with the distance from the radio transmit-
ter. They are often accompanied by distor-
tion.
Multi−path — FM signals are reflective,
making it possible for two signals to reach
your antenna at the same time. If this hap-
pens, the signals will cancel each other
out, causing a momentary flutter or loss of
reception.
Static and fluttering — These occur when
signals are blocked by buildings, trees, or
other large objects. Increasing the bass
level may reduce static and fluttering.
Station swapping — If the FM signal you
are listening to is interrupted or weakened,
and there is another strong station nearby
on the FM band, your radio may tune in the
second station until the original signal can
be picked up again.
AM
Fading — AM broadcasts are reflected by
the upper atmosphere — especially at
night. These reflected signals can inter-
fere with those received directly from the
radio station, causing the radio station to
sound alternately strong and weak.
Station interference — When a reflected
signal and a signal received directly from
a radio station are very nearly the same
frequency, they can interfere with each
other, making it difficult to hear the broad-
cast.
Static — AM is easily affected by external
sources of electrical noise, such as high
tension power lines, lightening, or electri-
cal motors. This results in static. XM

Cargo loaded on the roof luggage carrier,
especially metal objects, may adversely
affect the reception of XM  Satellite Radio.
Alternation or modifications carried out
without appropriate authorization may in-
validate the user’s right to operate the
equipment.
iPod 
About iPod  —
“Made for iPod” means that an elec-
tronic accessory has been designed to
connect specifically to iPod and has
been certified by the developer to meet
Apple performance standards.
Apple is not responsible for the opera-
tion of this device or its compliance with
safety and regulatory standards.
iPod is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.
Compatible models —
iPod  5th generation Ver. 1.2 or later
iPod nano  3rd generation Ver. 1.0 or
later
iPod nano  2nd generation Ver. 1.1.2
or later
iPod nano  Ver. 1.3 or later
iPod touch Ver. 1.1 or later
iPod classic  Ver. 1.0 or later
iPhone , iPod mini, iPod shuffle , iPod
photo and 4th generation and earlier mod-
els of iPod  are not compatible with this
system.
USB memory
USB memory that can be used for MP3
and WMA playback.
USB communication formats: USB 2.0
FS (12 MBPS)
File formats: FAT 16/32 (Windows )
Correspondence class: Mass storage
class

REAR VIEW MONITOR SYSTEM
200
The rear view monitor system assists
the driver by displaying an image of the
view behind the vehicle while backing
up. The left and right displayed on the
screen are the same as those of the in-
side rear view mirror.
Vehicles with smart key system —
To display the rear view image on the
screen, place the shift lever in the “R”
position when the “ENGINE START
STOP” switch is in IGNITION ON mode.
Vehicles without smart key system —
To display the rear view image on the
screen, place the shift lever in the “R”
position when the engine switch is in
the “ON” position.
If you move the shift lever out of the “R”
position, the screen returns to the previous
screen. Operating another function of the
navigation system will display another
screen.
The rear view monitor system is a supple-
ment device intended to assist back up.
When backing up, be sure to check behind
and all around the vehicle visually.
CAUTION
Never depend on the rear view
monitor system entirely when
backing up. Always make sure
your intended path is clear.
Use caution, just as you would
when backing up any vehicle.
Never back up while looking only at
the screen. The image on the
screen is different from actual
conditions. Depicted distances
between objects and flat surfaces
will differ from actual distance. If
you back up while looking only at
the screen, you may hit a vehicle, a
person or an object. When backing
up, be sure to check behind and all
around the vehicle visually and
with mirrors before proceeding.
Do not use the system when the
trunk is not completely closed.
Use your own eyes to confirm the
vehicle’s surroundings, as the dis-
played image may become faint or
dark, and moving images will be
distorted, or not entirely visible
when the outside temperature is
low. When backing up, be sure to
check behind and all around the ve-
hicle visually and with mirror be-
fore proceeding.
Do not use the system in the follow-
ing cases:
On icy or slick road surfaces, or
in snow.
When using tire chains or emer-
gency tires.
On an uneven road, such as a
slope.
Rear view monitor system —

INDEX
292 Numbers/Symbols
? button20, 32
. . . . . . . . . . . . . . . . . . . . . . . . .
3 Routes selection 72
. . . . . . . . . . . . . . . . . . .
A
A2DP
(Advanced Audio Distribution
Profile) 173 . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding destinations 82 . . . . . . . . . . . . . . . . . .
Address Book button 20, 64 . . . . . . . . . . . . .
Address book entry information 37 . . . . . . .
Address button 20, 53 . . . . . . . . . . . . . . . . . . .
Alphabet key 28 . . . . . . . . . . . . . . . . . . . . . . .
AM button 142, 145, 150 . . . . . . . . . . . . . . . .
AM tab 145, 150 . . . . . . . . . . . . . . . . . . . . . . .
Areas to avoid 113 . . . . . . . . . . . . . . . . . . . . .
Arrow screen 39, 78 . . . . . . . . . . . . . . . . . . . .
ASL 148 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUDIO button 142, 145 . . . . . . . . . . . . . . . . .
Audio button 22, 262 . . . . . . . . . . . . . . . . . . .
Audio remote controls 189 . . . . . . . . . . . . . . .
Audio settings 262 . . . . . . . . . . . . . . . . . . . . .
Audio system 141 . . . . . . . . . . . . . . . . . . . . . .
Audio system operating hints 190 . . . . . . . .
Auto avoid traffic 96, 216, 218 . . . . . . . . . . .
Auto complete text 216 . . . . . . . . . . . . . . . . .
Auto screen change 206 . . . . . . . . . . . . . . . .
Auto voice guidance 213 . . . . . . . . . . . . . . . .
Automatic recognition 213 . . . . . . . . . . . . . . .
Automatic sound levelizer 148 . . . . . . . . . . .
AUX adapter 150 . . . . . . . . . . . . . . . . . . . . . . .
AUX button 142, 145, 150, 178, 181 . . . . . .
AUX tab 145, 150 . . . . . . . . . . . . . . . . . . . . . .
AVRCP
(Audio/Video Remote Control
Profile) 173 . . . . . . . . . . . . . . . . . . . . . . . . . .
B
Balance 148
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic function 25
. . . . . . . . . . . . . . . . . . . . . . .
Bass 148
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Beep 206
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bluetooth  120, 173, 255, 262
. . . . . . . . . .
Bluetooth  audio operation 173
. . . . . . . . . .
Bluetooth  audio player 173, 262 . . . . . . . .
Bluetooth  connection statue
at start up 261
. . . . . . . . . . . . . . . . . . . . . . .
Bluetooth  information 263
. . . . . . . . . . . . . .
Brightness 31
. . . . . . . . . . . . . . . . . . . . . . . . . .
BT tab 145, 178
. . . . . . . . . . . . . . . . . . . . . . .
Building information 42
. . . . . . . . . . . . . . . . .
C
Calendar 140
. . . . . . . . . . . . . . . . . . . . . . . . . .
Calendar button 23, 140
. . . . . . . . . . . . . . . .
Calibration 216, 221
. . . . . . . . . . . . . . . . . . .
Call by call history 132
. . . . . . . . . . . . . . . . . .
Call by dial 129
. . . . . . . . . . . . . . . . . . . . . . . .
Call by phonebook 130
. . . . . . . . . . . . . . . . .
Call by POI call 136
. . . . . . . . . . . . . . . . . . . .
Call by speed dial 132
. . . . . . . . . . . . . . . . . .
Call by voice recognition 134
. . . . . . . . . . . .
Call history 132
. . . . . . . . . . . . . . . . . . . . . . . .
Call on the Bluetooth  phone 129 . . . . . . . .
Categories 59
. . . . . . . . . . . . . . . . . . . . . . . . .
CAUTION screen 26
. . . . . . . . . . . . . . . . . . .
CD button 142, 145, 164
. . . . . . . . . . . . . . . .
CD changer operation 161
. . . . . . . . . . . . . .
CD tab 145, 164
. . . . . . . . . . . . . . . . . . . . . . .
Cellular phone 120
. . . . . . . . . . . . . . . . . . . . .
Change “Icon” 109
. . . . . . . . . . . . . . . . . . . . .
Change “Location” 111, 116
. . . . . . . . . . . . . .
Change “Name” 110, 115
. . . . . . . . . . . . . . . .
Change “Phone #” 111
. . . . . . . . . . . . . . . . . .
Change “Show Name” 110, 115
. . . . . . . . . .
Change “Size” 116
. . . . . . . . . . . . . . . . . . . . .
Changing a device name 264
. . . . . . . . . . . .
Changing the Bluetooth  settings 256 . . . . .
Changing the device name 269
. . . . . . . . . .
Changing the handsfree power 256 . . . . . . .
Changing the map DVD −ROM 287 . . . . . . .
Changing the passcode 268
. . . . . . . . . . . . .
City center 60
. . . . . . . . . . . . . . . . . . . . . . . . .
City name 53, 58
. . . . . . . . . . . . . . . . . . . . . . .
City to search 53, 58
. . . . . . . . . . . . . . . . . . . .
Clock button 22, 211
. . . . . . . . . . . . . . . . . . . .
Clock settings 211
. . . . . . . . . . . . . . . . . . . . . .
Command list 47
. . . . . . . . . . . . . . . . . . . . . . .
Compass mode 41
. . . . . . . . . . . . . . . . . . . . .
Compass mode screen 39, 41
. . . . . . . . . . .
Connecting a Bluetooth 
audio player 176, 267
. . . . . . . . . . . . . . . .
Connecting a Bluetooth  phone 126 . . . . . .
Connecting a USB memory
or iPod  182
. . . . . . . . . . . . . . . . . . . . . . . .
Contacts 130, 237
. . . . . . . . . . . . . . . . . . . . .
Contrast 31
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Coordinates button 20, 69
. . . . . . . . . . . . . . .
Current position display 33
. . . . . . . . . . . . . .
Current

position/tire change
calibration 221
. . . . . . . . . . . . . . . . . . . . . . .
Cursor position as a destination 34 . . . . . . .
Cursor position as an address book entry 34
. . . . . . . . . . .
Customize POI icons 216, 219
. . . . . . . . . .