TOYOTA AVENSIS 2003 Service Repair Manual

670SG±02
67±24
±
AUDIO & VISUAL SYSTEM ANTENNA CORD SUB±ASSY NO.3
AVENSIS REPAIR MANUAL (RM1018E)
ANTENNA CORD SUB±ASSY NO.3
REPLACEMENT
1.DISCONNECT BATTERY NEGATIVE TERMINAL (See page 60±1)
2.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH NO.2 (See page 71±11)
3. REMOVE INSTRUMENT PANEL REGISTER ASSY CTR (W/ NAVIGATION SYSTEM) (See page 67±6)
4.REMOVE SHIFT LEVER KNOB SUB±ASSY (M/T TRANSAXLE) (See page 41±11)
5.REMOVE CONSOLE PANEL SUB±ASSY UPPER (See page 71±11)
6.REMOVE RADIO RECEIVER ASSEMBLY W/BRACKET (See page 67±5)
7.REMOVE CONSOLE BOX ASSY RR (See page 71±11)
8.REMOVE HEATER TO REGISTER DUCT NO.2 (See page 71±11)
9.REMOVE FRONT DOOR SCUFF PLATE RH (See page 76±36)
10.REMOVE REAR DOOR SCUFF PLATE RH (See page 76±36)
11.REMOVE COWL SIDE TRIM BOARD RH (See page 76±36)
12.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (See page 76±36)
13.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH (See page 76±36)
14. REMOVE REAR SEAT CUSHION ASSEMBLY
(See page 40/60 FOLDING FLIP±UP CUSHION 72±21, 40/60 FOLDING 72±27)
15. REMOVE REAR SEATBACK ASSY (See page 40/60 FOLDING FLIP±UP CUSHION 72±21, 40/60 FOLDING 72±27)
16. REMOVE REAR SIDE SEAT BACK ASSY RH (See page 40/60 FOLDING FLIP±UP CUSHION 72±21, 40/60 FOLDING 72±27)
17.REMOVE PACKAGE TRAY TRIM PANEL ASSY (See page 76±45)
18.REMOVE REAR FLOOR FINISH PLATE (See page 76±45)
19.REMOVE DECK TRIM SIDE PANEL ASSY RH (See page 76±45)
20.REMOVE ROOF SIDE GARNISH INNER RH (See page 76±45)
21.REMOVE FRONT SEAT ASSY RH (See page POWER SEAT 72±11, MANUAL SEAT 72±16)
22. REMOVE FLOOR CARPET ASSY FRONT
http://vnx.su

I35217Clamps
w/ Navigation:
w/ Navigation:
±
AUDIO & VISUAL SYSTEM ANTENNA CORD SUB±ASSY NO.3
67±25
AVENSIS REPAIR MANUAL (RM1018E)
23. REMOVE ANTENNA CORD SUB±ASSY NO.3
(a) Disconnect the connectors.
(b) w/ Navigation:
Remove the bolt, nut and screw.
w/o Navigation:
Remove the bolt and nut.
(c) w/ Navigation:
Remove the 11 clamps and the antenna cord sub±assy No.3.
w/o Navigation:
Remove the 10 clamps and the antenna cord sub±assy No.3.
http://vnx.su

67±26
±
AUDIO & VISUAL SYSTEMANTENNA CORD SUB±ASSY NO.3
AVENSIS REPAIR MANUAL (RM1018E)
24.INSTALL ANTENNA CORD SUB±ASSY NO.3
(a)Install the bolt. Torque: 7.0 N
m (71 kgf
cm, 62 in.
lbf)
(b)w/ Navigation: Install the nut and screw.
w/o Navigation:
Install the nut.
(c)w/ Navigation: Install the 11 clamps and the antenna cord sub±assy No.3.
w/o Navigation:
Install the 10 clamps and the antenna cord sub±assy No.3.
25.INSTALL REAR SEATBACK ASSY
(See page 40/60 FOLDING FLIP±UP CUSHION 72±21, 40/60 FOLDING 72±27)
26.INSTALL FRONT SEAT ASSY RH (See page POWER SEAT 72±11, MANUAL SEAT 72±16)
http://vnx.su

670S4±01
±
AUDIO & VISUAL SYSTEM AUDIO & VISUAL SYSTEM
67±1
AVENSIS REPAIR MANUAL (RM1018E)
AUDIO & VISUAL SYSTEM
PRECAUTION
1. OBSERVE HANDLING AND OPERATIONAL PRECAUTIONS
(a) Please explain to the customer that when the negative terminal is disconnected from the batter\
y, the
channel information memory of the AM/FM broadcast stations in the radio receive\
r is cleared. If neces-
sary, make a note of the recorded channel information before the negative ter\
minal is disconnected,
then reset the information after the negative terminal is reconnected.
(b) The removal/installation of the radio receiver should be performed after al\
l the cassette tapes and au- dio CDs are ejected from the radio receiver.
HINT:
If the cassette tapes and the audio CDs cannot be ejected due to the malfu\
nction of the radio receiver, do
not try to drag them out by force. Bring the vehicle to the repair plant\
.
(c) Fasten the earth bolt securely when the antenna cord is removed or insta\
lled.
HINT:
Failing to fasten the earth bolt securely causes noise at the time of ra\
dio wave reception.
(d) Do not touch the cone paper of the speaker.
http://vnx.su

670S5±01
I35223
Instrument Cluster Finish Panel Garnish No.2
Radio Bracket No.2 Radio Receiver Assy
Instrument Panel
Register Assy CTR Air Conditioning Control Assy Console Panel
Sub±assy Upper
Navigation System: Navigation Computer Cover
Instrument Panel
Support No.3
Instrument Panel
Support No.1
Instrument Panel
Support No.2
Door Control Motor Door Control Switch
Assy (TILT)
Instrument Cluster Finish Panel Assy Door Control Switch
Instrument Cluster Finish
Upper Panel Multi±display
Instrument Panel Box
Door Cover Radio Bracket No.1
Instrument Panel
Register Control Gear
Control Knob
Protector No.1
Position Sensor
67±2
±
AUDIO & VISUAL SYSTEM AUDIO & VISUAL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
COMPONENTS
http://vnx.su

I35224
Front No.2 Speaker AssyAmplifier Antenna Assy
Front No.1 Speaker
Assy
Rear Speaker Assy Navigation System:
Disc Player Bracket No.2
Rivet
Navigation ECUPower Point Socket Cover
Power Point Socket Assy
Liftback:
Antenna Cord Sub±assy No.3 Amplifier Antenna Assy
Wagon:
Non±reusable part



Disc Player Bracket No.3
Rivet


Rear No.2 Speaker Assy
Navigation ECU Cover
±
AUDIO & VISUAL SYSTEM AUDIO & VISUAL SYSTEM
67±3
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

I35225
Navigation System:Navigation Antenna Assy
Cigarette lighter Socket &
Retainer Assy
Cigarette lighter Knob
& Element Assy
67±4
±
AUDIO & VISUAL SYSTEM AUDIO & VISUAL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

670SJ±01
I35195
I35197Claw
I35196
I35205
±
AUDIO & VISUAL SYSTEM CIGARETTE LIGHTER ASSY
67±29
AVENSIS REPAIR MANUAL (RM1018E)
CIGARETTE LIGHTER ASSY
REPLACEMENT
1.REMOVE CONSOLE PANEL SUB±ASSY UPPER (See page 71±11)
2. REMOVE FRONT ASH RECEPTACLE ASSY
(a) Using a torx socket wrench (T20), remove the 4 screwsand front ash receptacle assy.
3. RE MO V E FRO NT AS H RE CE P TACLE RE TAINE R SUB±ASSY
(a) Disengage the claw and disconnect the connector.
(b) Push up the corner of the outer case open and remove the retainer assy as shown in the illustration.
4. REMOVE CIGARETTE LIGHTER ASSY
(a) Remove the 2 springs.
http://vnx.su

I351992 Claws
I35200
I35203
I35204
5.0mm
(0.20in.)
I35205
67±30
±
AUDIO & VISUAL SYSTEM CIGARETTE LIGHTER ASSY
AVENSIS REPAIR MANUAL (RM1018E)
(b) Disengage the 2 claws and remove the door.
(c) Push out the cigarette lighter housing to the room side.
(d) Push out the cigarette lighter ring w/ wire harness to the room side.
5. INSTALL CIGARETTE LIGHTER ASSY
(a) Align the claws of the cigarette lighter ring with the notches of the cigarette lighter box to fix the cigarette
lighter w/ wire harness.
(b) Push the cigarette lighter housing to the out side.
(c) Install the wire harness as shown in the illustration.
(d) Place the wire harness in the position shown in the il- lustration and install the door cover.
(e) Install the 2 springs.
http://vnx.su

I35206
I35195
±
AUDIO & VISUAL SYSTEM CIGARETTE LIGHTER ASSY
67±31
AVENSIS REPAIR MANUAL (RM1018E)
(f) Make sure that the 2 springs are hooked on the claws and
install the retainer assy.
(g) Connect the connecter.
(h) Using a torx socket wrench (T20), install the 4 screws and
front ash receptacle.
http://vnx.su