height TOYOTA AVENSIS 2003 Service Owner's Manual

EM1628
EM2011
EM2538
±
ENGINE MECHANICAL PARTIAL ENGINE ASSY (1ZZ±FE/3ZZ±FE)
14±13
1ZZ±FE,3ZZ±FE ENGINE REPAIR MANUAL
(RM923E)
39. INSPECT CAMSHAFT
(a) Inspect camshaft for runout.
(1) Place the camshaft on V±blocks.
(2) Using a dial indicator, measure the circle runout at
the center journal.
Maximum circle runout: 0.03 mm (0.0012 in.)
(b) Inspect cam lobes. (1) Using a micrometer, measure the cam lobe height.
Standard cam lobe height:
Intake 44.333 ± 44.433 mm (1.7454 ± 1.7493 in.)
Exhaust 43.761 ± 43.861 mm (1.7229 ± 1.7268 in.)
Minimum cam lobe height:
Intake 44.18 mm (1.7394 in.)
Exhaust 43.61 mm (1.7169 in.)
(c) Inspect camshaft journals. (1) Using a micrometer, measure the journal diameter.
No. 1 journal diameter:
34.449 ± 34.465 mm (1.3563 ± 1.3569 in.)
Others journal diameter:
22.949 ± 22.965 mm (0.9035 ± 0.9041 in.)
If the journal diameter is not as specified, check the oil clear-
ance.
40. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB±ASSY
(a) Apply two or three threads of adhesive to the drain union, and install i\
t within 3 minutes. Torque: 20 N
m (204 kgf
cm15 ft
lbf)
(b) After applying the specified torque, rotate the drain union clockwise until i\
ts drain port faces downward.
NOTICE:

Do not put into coolant in an hour after the installation.

Do not rotate the drain union more than 360 in (b), and never loosen it after setting the union
correctly.
41. INSTALL OIL STRAINER SUB±ASSY
(a) Install a new gasket and the oil strainer with the 2 nuts and a bolt. Torque: 9.0 N
m (92 kgf
cm, 80 in.
lbf)
http://vnx.su

010BJ±01
±
INTRODUCTION TERMS (1ZZ±FE/3ZZ±FE)
01±7
1ZZ±FE,3ZZ±FE ENGINE REPAIR MANUAL
(RM923E)
TERMS (1ZZ±FE/3ZZ±FE)
ABBREVIATIONS USED IN THIS MANUAL
AbbreviationsMeaning
ABSAnti±Lock Brake System
A/CAir Conditioner
ACAlternating Current
ACCAccessory
ACISAcoustic Control Induction System
ACSDAutomatic Cold Start Device
A.D.D.Automatic Disconnecting Differential
A/FAir±Fuel Ratio
AHCActive Height Control Suspension
ALRAutomatic Locking Retractor
ALTAlternator
AMPAmplifier
ANTAntenna
APPROX.Approximately
ASSYAssembly
A/TAutomatic Transmission (Transaxle)
AT FAutomatic Transmission Fluid
AUTOAutomatic
AUXAuxiliary
AV GAverage
AV SAdaptive Variable Suspension
B+Battery Voltage
BACSBoost Altitude Compensation System
BATBattery
BDCBottom Dead Center
B/LBi±Level
B/SBore±Stroke Ratio
BTDCBefore Top Dead Center
BVSVBimetallic Vacuum Switching Valve
CBCircuit Breaker
CCoCatalytic Converter For Oxidation
CDCompact Disc
CFCornering Force
CGCenter Of Gravity
CHChannel
CKDComplete Knock Down
COMB.Combination
CPECoupe
CPSCombustion Pressure Sensor
CPUCentral Processing Unit
CRSChild Restraint System
CTRCenter
C/VCheck Valve
CVControl Valve
CWCurb Weight
DCDirect Current
DEFDefogger
DFLDeflector
http://vnx.su

±
INTRODUCTION TERMS (1ZZ±FE/3ZZ±FE)
01±9
1ZZ±FE,3ZZ±FE ENGINE REPAIR MANUAL
(RM923E)Abbreviations Meaning
ICIntegrated Circuit
IDIIndirect Diesel Injection
IFSIndependent Front Suspension
IGIgnition
IIAIntegrated Ignition Assembly
INIntake (Manifold, Valve)
INTIntermittent
I/PInstrument Panel
IRSIndependent Rear Suspension
ISCIdle Speed Control
J/BJunction Block
J/CJunction Connector
KDKick±Down
LANLocal Area Network
LBLiftback
LCDLiquid Crystal Display
LEDLight Emitting Diode
LHLeft±Hand
LHDLeft±Hand Drive
L/H/WLength, Height, Width
LLCLong±Life Coolant
LNGLiquified Natural Gas
LOLow
LPGLiquified Petroleum Gas
LSDLimited Slip Differential
LSP & PVLoad Sensing Proportioning And Bypass Valve
LSPVLoad Sensing Proportioning Valve
MAPManifold Absolute Pressure
MAX.Maximum
MICMicrophone
MILMalfunction Indicator Lamp
MIN.Minimum
MPMultipurpose
MPIMultipoint Electronic Injection
MPXMultiplex Communication System
M/TManual Transmission
MTMount
MTGMounting
NNeutral
NANatural Aspiration
NO.Number
O2SOxygen Sensor
O/DOverdrive
OEMOriginal Equipment Manufacturing
OHCOverhead Camshaft
OHVOverhead Valve
OPTOption
O/SOversize
P & BVProportioning And Bypass Valve
PCSPower Control System
PCVPositive Crankcase Ventilation
http://vnx.su

0300O±02
03±4
±
SERVICE SPECIFICATIONS ENGINE MECHANICAL
1ZZ±FE,3ZZ±FE ENGINE REPAIR MANUAL
(RM923E)
ENGINE MECHANICAL
SERVICE DATA
Chain sub±assy
Length at 16 links Maximum
112.6 mm (4.433 in.)
Camshaft timing gear or sprocket
Diameter (w/ chain) Minimum
97.3 mm (3.831 in.)
Crankshaft timing gear or sprocket
Diameter (w/ chain) Minimum
51.6 mm (2.032 in.)
Chain tensioner slipper
Wear Maximum
1.0 mm (0.039 in.)
Chain vibration damper No. 1
Wear maximum
1.0 mm (0.039 in.)
Cylinder head set bolt
Length Standard Maximum
156.0 ± 159.0 mm (6.142 ± 6.260 in.)
159.5 mm (6.280 in.)
Camshaft
Circle runout Maximum
Lobe height Standard Intake
Exhaust
Minimum Intake Exhaust
Journal diameter No. 1 Others
Thrust clearance Standard
Maximum
Oil clearance Standard Maximum
0.03 mm (0.0012 in.)
44.333 ± 44.433 mm (1.7454 ± 1.7493 in.)
43.761 ± 43.861 mm (1.7229 ± 1.7268 in.)
44.18 mm (1.7394 in.)
43.61 mm (1.7169 in.)
34.449 ± 34.465 mm (1.3563 ± 1.3569 in.)
22.949 ± 22.965 mm (0.9035 ± 0.9041 in.)
0.040 ± 0.095 mm (0.0009 ± 0.0023 in.)
0.110 mm (0.0043 in.)
0.035 ± 0.072 mm (0.0014 ± 0.0028 in.)
0.10 mm (0.0039 in.)
Valve clearance (Cold) Intake
Exhaust0.15 ± 0.25 mm (0.006 ± 0.010 in.)
0.25 ± 0.35 mm (0.010 ± 0.014 in.)
Cylinder head sub±assy
Warpage Maximum Cylinder block side Intake manifold side
Exhaust manifold side
0.05 mm (0.0020 in.)
0.10 mm (0.0040 in.)
0.10 mm (0.0040 in.)
Valve guide bushing
Inside diameter
Oil clearance Standard Intake Exhaust
Maximum Intake Exhaust
Bore diameter
Protrusion height
5.510 ± 5.530 mm (0.2169 ± 0.2177 in.)
0.025 ± 0.060 mm (0.0010 ± 0.0024 in.)
0.030 ± 0.065 mm (0.0012 ± 0.0026 in.)
0.08 mm (0.0031 in.)
0.01 mm (0.0039 in.)
10.285 ± 10.306 mm (0.4049 ± 0.4057 in.)
8.7 ± 9.1 mm (0.342 ± 0.358 in.)
Valve stem
Diameter Intake Exhaust
5.470 ± 5.485 mm (0.2154 ± 0.2159 in.)
5.465 ± 5.480 mm (0.2152 ± 0.2158 in.)
Inner compression spring
Free length
Deviation Maximum
Angle (reference) Maximum
43.40 mm (1.7087 in.)
2.0 mm (0.078 in.)
2

Valve
Overall length Standard Intake
Exhaust
Minimum Intake Exhaust
Head margin thickness Standard
Minimum
88.65 mm (3.4902 in.)
88.69 mm (3.4917 in.)
88.35 mm (3.4874 in.)
88.39 mm (3.4799 in.)
1.0 mm (0.039 in.)
0.7 mm (0.028 in.)
http://vnx.su

±
SERVICE SPECIFICATIONS ENGINE MECHANICAL
03±5
1ZZ±FE,3ZZ±FE ENGINE REPAIR MANUAL
(RM923E)
Valve lifter
Diameter
Bore diameter
Oil clearance Standard
Maximum
30.966 ± 30.976 mm (1.2191 ± 1.2195 in.)
31.000 ± 31.025 mm (1.2205 ± 1.2215 in.)
0.024 ± 0.059 mm (0.0016 ± 0.0037 in.)
0.1 mm (0.0039 in.)
Straight pin
Protrusion height
5 mm (0.20 in.)
Union protrusion
Protrusion height Standard A B
C
29 mm (1.14 in.)
66.5 mm (2.62 in.)
24 mm (0.95 in.)
Connecting rod sub±assy
Thrust clearance Standard Maximum
Oil clearance Standard Maximum
Out±of alignment Maximum per/100 mm (3.94 in.)
Twist Maximum per/100 mm (3.94 in.)
0.160 ± 0.342 mm (0.063 ± 0.0135 in.)
0.342 mm (0.0135 in.)
0.028 ± 0.060 mm (0.0011 ± 0.0024 in.)
0.080 mm (0.0031 in.)
0.05 mm (0.0020 in.)
0.05 mm (0.0020 in.)
Connecting rod bearing
Center wall thickness Reference Mark 1 Mark 2
Mark 3
1.486 ± 1.490 mm (0.0585 ± 0.0587 in.)
1.490 ± 1.494 mm (0.0587 ± 0.0588 in.)
1.494 ± 1.498 mm (0.0588 ± 0.0590 in.)
Crankshaft
Thrust clearance StandardMaximum
Circle runout Maximum
Main journal diameter Maximum taper and out±of±round
Oil clearance Standard Maximum
0.04 ± 0.24 mm (0.0016 ± 0.0094 in.)
0.30 mm (0.0118 in.)
0.03 mm (0.0012 in.)
47.988 ± 48.000 mm (1.8893 ± 1.8898 in.)
0.02 mm (0.0008 in.)
0.013 ± 0.030 mm (0.0005 ± 0.0012 in.)
0.05 mm (0.0020 in.)
Cylinder block sub±assy
Warpage Maximum
Bore diameter StandardMaximum
0.05 mm (0.0020 in.)
79.000 ± 79.013 mm (3.1073 ± 3.1108 in.)
79.013 mm (3.1108 in.)
Piston
Diameter (at 29.8 mm (1.173 in.) from the piston head) 1ZZ±FE 3ZZ±FE
Oil clearance Standard 1ZZ±FE 3ZZ±FE
Maximum 1ZZ±FE
3ZZ±FE
78.925 ± 78.935 mm (3.1073 ± 3.1077 in.)
78.955 ± 78.965 mm (3.1085 ± 3.1089 in.)
0.065 ± 0.088 mm (0.0026 ± 0.0035 in.)
0.035 ± 0.058 mm (0.0014 ± 0.0023 in.)
0.088 mm (0.0035 in.)
0.058 mm (0.0023 in.)
Piston ring
Groove clearance No. 1 No. 2
End gap Standard No. 1 No. 2
Maximum No. 1
No. 2
0.020 ± 0.070 mm (0.0008 ± 0.0028 in.)
0.030 ± 0.070 mm
0.25 ± 0.35 mm (0.0098 ± 0.0138 in.)
0.35 ± 0.50 mm (0.0138 ± 0.0197 in.)
0.74 mm (0.029 in.)
0.89 mm (0.035 in.)
Piston pin
Diameter
20.004 ± 20.013 mm (0.7876 ±0.7879 in.)
Connecting rod bolt
Diameter Standard Maximum
6.6 ±6.7 mm (0.260 ± 0.264 in.)
6.4 mm (0.252 in.)
Crank pin
DiameterMaximum taper and out±of±round
43.992 ± 44.000 mm (1.7320 ± 1.7323 in.)
0.02 mm (0.0008 in.)
Crankshaft bearing cap set bolt
Diameter Standard Maximum
7.3 ± 7.5 mm (0.287 ± 0.295 in.)
7.2 mm (0.283 in.)
http://vnx.su

0300O±02
03±4
±
SERVICE SPECIFICATIONS ENGINE MECHANICAL
1ZZ±FE,3ZZ±FE ENGINE REPAIR MANUAL
(RM923E)
ENGINE MECHANICAL
SERVICE DATA
Chain sub±assy
Length at 16 links Maximum
112.6 mm (4.433 in.)
Camshaft timing gear or sprocket
Diameter (w/ chain) Minimum
97.3 mm (3.831 in.)
Crankshaft timing gear or sprocket
Diameter (w/ chain) Minimum
51.6 mm (2.032 in.)
Chain tensioner slipper
Wear Maximum
1.0 mm (0.039 in.)
Chain vibration damper No. 1
Wear maximum
1.0 mm (0.039 in.)
Cylinder head set bolt
Length Standard Maximum
156.0 ± 159.0 mm (6.142 ± 6.260 in.)
159.5 mm (6.280 in.)
Camshaft
Circle runout Maximum
Lobe height Standard Intake
Exhaust
Minimum Intake Exhaust
Journal diameter No. 1 Others
Thrust clearance Standard
Maximum
Oil clearance Standard Maximum
0.03 mm (0.0012 in.)
44.333 ± 44.433 mm (1.7454 ± 1.7493 in.)
43.761 ± 43.861 mm (1.7229 ± 1.7268 in.)
44.18 mm (1.7394 in.)
43.61 mm (1.7169 in.)
34.449 ± 34.465 mm (1.3563 ± 1.3569 in.)
22.949 ± 22.965 mm (0.9035 ± 0.9041 in.)
0.040 ± 0.095 mm (0.0009 ± 0.0023 in.)
0.110 mm (0.0043 in.)
0.035 ± 0.072 mm (0.0014 ± 0.0028 in.)
0.10 mm (0.0039 in.)
Valve clearance (Cold) Intake
Exhaust0.15 ± 0.25 mm (0.006 ± 0.010 in.)
0.25 ± 0.35 mm (0.010 ± 0.014 in.)
Cylinder head sub±assy
Warpage Maximum Cylinder block side Intake manifold side
Exhaust manifold side
0.05 mm (0.0020 in.)
0.10 mm (0.0040 in.)
0.10 mm (0.0040 in.)
Valve guide bushing
Inside diameter
Oil clearance Standard Intake Exhaust
Maximum Intake Exhaust
Bore diameter
Protrusion height
5.510 ± 5.530 mm (0.2169 ± 0.2177 in.)
0.025 ± 0.060 mm (0.0010 ± 0.0024 in.)
0.030 ± 0.065 mm (0.0012 ± 0.0026 in.)
0.08 mm (0.0031 in.)
0.01 mm (0.0039 in.)
10.285 ± 10.306 mm (0.4049 ± 0.4057 in.)
8.7 ± 9.1 mm (0.342 ± 0.358 in.)
Valve stem
Diameter Intake Exhaust
5.470 ± 5.485 mm (0.2154 ± 0.2159 in.)
5.465 ± 5.480 mm (0.2152 ± 0.2158 in.)
Inner compression spring
Free length
Deviation Maximum
Angle (reference) Maximum
43.40 mm (1.7087 in.)
2.0 mm (0.078 in.)
2

Valve
Overall length Standard Intake
Exhaust
Minimum Intake Exhaust
Head margin thickness Standard
Minimum
88.65 mm (3.4902 in.)
88.69 mm (3.4917 in.)
88.35 mm (3.4874 in.)
88.39 mm (3.4799 in.)
1.0 mm (0.039 in.)
0.7 mm (0.028 in.)
http://vnx.su

±
SERVICE SPECIFICATIONS ENGINE MECHANICAL
03±5
1ZZ±FE,3ZZ±FE ENGINE REPAIR MANUAL
(RM923E)
Valve lifter
Diameter
Bore diameter
Oil clearance Standard
Maximum
30.966 ± 30.976 mm (1.2191 ± 1.2195 in.)
31.000 ± 31.025 mm (1.2205 ± 1.2215 in.)
0.024 ± 0.059 mm (0.0016 ± 0.0037 in.)
0.1 mm (0.0039 in.)
Straight pin
Protrusion height
5 mm (0.20 in.)
Union protrusion
Protrusion height Standard A B
C
29 mm (1.14 in.)
66.5 mm (2.62 in.)
24 mm (0.95 in.)
Connecting rod sub±assy
Thrust clearance Standard Maximum
Oil clearance Standard Maximum
Out±of alignment Maximum per/100 mm (3.94 in.)
Twist Maximum per/100 mm (3.94 in.)
0.160 ± 0.342 mm (0.063 ± 0.0135 in.)
0.342 mm (0.0135 in.)
0.028 ± 0.060 mm (0.0011 ± 0.0024 in.)
0.080 mm (0.0031 in.)
0.05 mm (0.0020 in.)
0.05 mm (0.0020 in.)
Connecting rod bearing
Center wall thickness Reference Mark 1 Mark 2
Mark 3
1.486 ± 1.490 mm (0.0585 ± 0.0587 in.)
1.490 ± 1.494 mm (0.0587 ± 0.0588 in.)
1.494 ± 1.498 mm (0.0588 ± 0.0590 in.)
Crankshaft
Thrust clearance StandardMaximum
Circle runout Maximum
Main journal diameter Maximum taper and out±of±round
Oil clearance Standard Maximum
0.04 ± 0.24 mm (0.0016 ± 0.0094 in.)
0.30 mm (0.0118 in.)
0.03 mm (0.0012 in.)
47.988 ± 48.000 mm (1.8893 ± 1.8898 in.)
0.02 mm (0.0008 in.)
0.013 ± 0.030 mm (0.0005 ± 0.0012 in.)
0.05 mm (0.0020 in.)
Cylinder block sub±assy
Warpage Maximum
Bore diameter StandardMaximum
0.05 mm (0.0020 in.)
79.000 ± 79.013 mm (3.1073 ± 3.1108 in.)
79.013 mm (3.1108 in.)
Piston
Diameter (at 29.8 mm (1.173 in.) from the piston head) 1ZZ±FE 3ZZ±FE
Oil clearance Standard 1ZZ±FE 3ZZ±FE
Maximum 1ZZ±FE
3ZZ±FE
78.925 ± 78.935 mm (3.1073 ± 3.1077 in.)
78.955 ± 78.965 mm (3.1085 ± 3.1089 in.)
0.065 ± 0.088 mm (0.0026 ± 0.0035 in.)
0.035 ± 0.058 mm (0.0014 ± 0.0023 in.)
0.088 mm (0.0035 in.)
0.058 mm (0.0023 in.)
Piston ring
Groove clearance No. 1 No. 2
End gap Standard No. 1 No. 2
Maximum No. 1
No. 2
0.020 ± 0.070 mm (0.0008 ± 0.0028 in.)
0.030 ± 0.070 mm
0.25 ± 0.35 mm (0.0098 ± 0.0138 in.)
0.35 ± 0.50 mm (0.0138 ± 0.0197 in.)
0.74 mm (0.029 in.)
0.89 mm (0.035 in.)
Piston pin
Diameter
20.004 ± 20.013 mm (0.7876 ±0.7879 in.)
Connecting rod bolt
Diameter Standard Maximum
6.6 ±6.7 mm (0.260 ± 0.264 in.)
6.4 mm (0.252 in.)
Crank pin
DiameterMaximum taper and out±of±round
43.992 ± 44.000 mm (1.7320 ± 1.7323 in.)
0.02 mm (0.0008 in.)
Crankshaft bearing cap set bolt
Diameter Standard Maximum
7.3 ± 7.5 mm (0.287 ± 0.295 in.)
7.2 mm (0.283 in.)
http://vnx.su

F45154
Rack & Pinion
Power Steering Gear AssyTie Rod End
Sub±assy LH
Front Stabilizer Link
Assy LH
Stabilizer Bar Front
Front Stabilizer Link
Assy RH
Front Suspension Arm
Sub±assy Lower No.1 RH
Front Suspension
Member Brace
Rear RH Front Stabilizer
Bar Bush No.1
Front Suspension
Crossmember Sub±assy
Front Suspension
Arm Sub±assy
Lower No.1 LH
Body Mounting
Stopper Rear
Front Suspension
Member Body
Mounting Stopper FR
Front Suspension
Member Brace Rear LH
Cotter Pin


89 (908, 66)
133 (1,360, 98)
49 (500, 36)
74 (755, 55)
80 (816, 59)
133 (1,360, 98)
74 (755, 55)
49 (500, 36)
80 (816, 59)
19 (194, 14)
19 (194, 14)
133 (1,360, 98)
80 (816, 59)
133 (1,360, 98)
80 (816, 59)
19 (194, 14)
49 (500, 36)
74 (755, 55)
N
m (kgf
cm, ft
lbf) : Specified torque
Non±reusable part


5.4 (55, 48 in.
lbf)w/ HID:
HID Height
Control Sensor
Front Stabilizer
Bracket No.1 RH
Front Stabilizer
Bracket No.1 LH
96 (979, 71)
80 (816, 59)
52 (530, 38)
±
FRONT SUSPENSION FRONT SUSPENSION
26±5
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

C95317
C86742
C87504
C95318
±
FRONT SUSPENSION FRONT SUSPENSION ARM SUB±ASSY LOWER NO.1
LH (ATM)26±17
AVENSIS REPAIR MANUAL (RM1018E)
10. REMOVE FRONT SUSPENSION MEMBER B RACE
REAR LH
(a) Support the front suspension crossmember sub±assy
with a transmission jack.
(b) Remove the 4 bolts and front suspension member brace rear LH.
(c) Remove the front suspension member body mounting
stopper rear from the front suspension member brace
rear LH.
11. REMOVE FRONT SUSPENSION MEMBER BRACE REAR RH
HINT:
Remove the RH side by the same procedures as the LH side.
12. SEPARATE FRONT SUSPENSION CROSSMEMBERSUB±ASSY
(a) w/ HID: Disconnect the height control sensor (Front) connector.
(b) Remove the 3 bolts and 3 nuts, disconnect the transverse
engine engine mounting insulator and engine mounting
member sub±assy center from the front suspension
crossmember sub±assy.
(c) Remove the 2 nuts and 2 front suspension member body mounting stoppers front.
(d) Lower the transmission jack, remove the front suspension crossmember sub±assy.
13. REMOVE FRONT SUSPENSION ARM SUB±ASSY LOWER NO.1 LH
(a) Remove the 2 bolts, nut and lower suspension arm sub±
assy lower No.1 LH from the front suspension crossmem-
ber sub±assy.
http://vnx.su

C95318
C87504
C86742
AA
AAB
B
C95317
AA
A
B
26±18
±
FRONT SUSPENSIONFRONT SUSPENSION ARM SUB±ASSY LOWER NO.1
LH(ATM)
AVENSIS REPAIR MANUAL (RM1018E)
14.TEMPORARILY TIGHTEN FRONT SUSPENSION ARM SUB±ASSY LOWER NO.1 LH
(a)Install the lower suspension arm sub±assy lower No.1
LH, and temporarily tighten the 2 bolts and nut.
15.INSTALL FRONT SUSPENSION CROSSMEMBER SUB±ASSY
(a)Support the front suspension crossmember sub±assy with a transmission jack.
(b)Install the 2 front suspension member body mounting stoppers front and 2 nuts.
Torque: 133 N
m (1,360 kgf
cm, 98 ft
lbf)
(c)Connect the transverse engine engine mounting insula- tor and engine mounting member sub±assy center to the
front suspension crossmember sub±assy.
(d)Install the 3 bolts and 3 nuts. Torque:
Bolt A: 52 N
m (530 kgf
cm, 38 ft
lbf)
Bolt B: 96 N
m (979 kgf
cm, 71 ft
lbf)
(e)w/ HID: Connect the height control sensor (Front) connector.
16.INSTALL FRONT SUSPENSION ME MBER BRACE
REAR LH
(a)Install the front suspension member body mounting stop- per rear to the front suspension member brace rear LH.
(b)Install the 4 bolts and front suspension member brace rear LH.
Torque:
Bolt A: 80 N
m (816 kgf
cm, 59 ft
lbf)
Bolt B: 133 N
m (1,360 kgf
cm, 98 ft
lbf)
17.INSTALL FRONT SUSPENSION MEMBER BRACE REAR RH
HINT:
Install the RH side by the same procedures as the LH side.
18.CONNECT RACK & PINION POWER STEERING GEAR ASSY
(a)Electric power steering model: See page 51±28
(b)Oil pressure power steering model: See page 51±36
http://vnx.su