fuses TOYOTA CAMRY 2007 XV40 / 8.G Owners Manual

’07Camry_U (L/O 0608)
243
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
Cancel operation—
Do either one of the following:
Push the onhook switch at anytime
during the operation.
Push the talk switch and say “Can-
cel” after the beep at anytime dur-
ing the operation except while a call
is connected.
When receiving a phone call, a ring tone
is audible and the system changes into
the telephone mode.
When receiving a phone call, the display
is as follows. The display differs depend-
ing on whether or not the vehicle is in
motion.
When the vehicle is stopped:
Number, name, or “Incoming” is displayed.
When the vehicle is in motion:
“Incoming” is displayed.
Do either one of the following:
Pushing the off−hook switch allows you
to talk on the phone.
Pushing the on−hook switch refuses
the call.
To adjust the ring volume, push “+” or “−”
on the steering volume controls. Volume
adjustment cannot be done using the au-
dio system.
Repeatedly pushing “−” on the steering
volume controls mutes the ring.
When receiving an international phone
call, the name of the party may not be
displayed correctly depending on the cellu-
lar phone.To transfer a call to the phone:
The received call can be transferred from
the hands−free system to the cellular
phone that is connected to Bluetooth. For
details, refer to the user’s guide for the
cellular phone.
—Receiving a phone call

’07Camry_U (L/O 0608)
374
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
Spare fusesIf you perform maintenance by yourself,
be sure to follow the correct procedure
given in this Section.
You should be aware that improper or in-
complete servicing may result in operating
problems.
Performing do−it−yourself maintenance
during the warranty period may affect your
warranty coverage. Read the separate
Toyota Warranty statement for details and
suggestions.
This Section gives instructions only for
those items that are relatively easy for an
owner to perform. As explained in Section
6, there are still a number of items that
must be done by a qualified technician
with special tools.
For information on tools and parts for do−
it−yourself maintenance, see “Parts and
tools” on page 378 in this Section.
Utmost care should be taken when work-
ing on your vehicle to prevent accidental
injury. Here are a few precautions that
you should be especially careful to ob-
serve:
Fuse locationsDoityourself service
precautions

’07Camry_U (L/O 0608)
378
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
Here is a list of parts and tools you will
need to perform do−it−yourself mainte-
nance. Remember all Toyota parts are de-
signed in metric sizes, so your tools must
be metric.
CHECKING THE ENGINE OIL LEVEL
Parts (if level is low):
“Toyota Genuine Motor Oil” or equiva-
lent
See page 381 in Section 7−2 for de-
tails about engine oil selection.
Tools:
Rag or paper towel
Funnel (only for adding oil)
CHECKING THE ENGINE COOLANT
LEVEL
Parts (if level is low):
“Toyota Super Long Life Coolant” or
similar high quality ethylene glycol
based non−silicate, non−amine, non−ni-
trite, and non−borate coolant with long−
life hybrid organic acid technology.
“Toyota Super Long Life Coolant” is a
mixture of 50% coolant and 50% deion-
ized water (for the U.S.A.) or 55%
coolant and 45% deionized water (for
Canada).Tools:
Funnel (only for adding coolant)
CHECKING BRAKE FLUID
Parts (if level is low):
SAE J1703 or FMVSS No.116 DOT 3
brake fluid
Tools:
Rag or paper towel
Funnel (only for adding fluid)
CHECKING POWER STEERING FLUID
Parts (if level is low):
Automatic transmission fluid
DEXRONII or III
Tools:
Rag or paper towel
Funnel (only for adding fluid)
CHECKING BATTERY CONDITION
Tools:
Warm water
Baking soda
Grease
Conventional wrench (for terminal
clamp bolts)CHECKING AND REPLACING FUSES
Parts (if replacement is necessary):
Genuine Toyota fuse or equivalent with
same amperage rating as original
ADDING WASHER FLUID
Parts:
Water
Washer fluid containing antifreeze (for
winter use)
Tools:
Funnel
REPLACING LIGHT BULBS
Parts:
Bulb with same number and wattage
rating as original (See charts in “Re-
placing light bulbs” on page 400 in
Section 7−3.)
Parts and tools

’07Camry_U (L/O 0608)
395
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
DOITYOURSELF MAINTENANCE
Electrical components
Checking battery condition396 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery recharging precautions397 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking and replacing fuses398 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding washer fluid399 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing light bulbs400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 3

’07Camry_U (L/O 0608)
398
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
Good Blown
Ty p e A
Good Blown
Ty p e B
Good Blown
Ty p e C
If the headlights or other electrical
components do not work, check the
fuses. If any of the fuses are blown,
they must be replaced.
See “Fuse locations” on page 374 in Sec-
tion 7−1 for locations of the fuses.
Turn the ignition switch and inoperative
component off. Pull the suspected fuse
straight out and check it.
Determine which fuse may be causing the
problem. The lid of the fuse box shows
the name of the circuit for each fuse. See
page 412 in Section 8 for the functions
controlled by each circuit.
Type B fuses—When any of the fuses are
blown, contact your Toyota dealer.
Checking and replacing fuses

’07Camry_U (L/O 0608)
399
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
Type A fuses can be pulled out by the
pull−out tool. The location of the pull−out
tool is shown in the illustration.
If you are not sure whether the fuse has
blown, try replacing the suspected fuse
with one that you know is good.
If the fuse has blown, push a new fuse
into the clip.
Only install a fuse with the amperage rat-
ing designated on the fuse box lid.
If you do not have a spare fuse, in an
emergency you can pull out the “MIR
HTR” or “PWR OUTLET” fuse, which may
be dispensable for normal driving, and use
it if its amperage rating is the same.
If you cannot use one of the same amper-
age, use one that is lower, but as close
to the rating as possible. If the amperage
is lower than that specified, the fuse
might blow out again but this does not
indicate anything wrong. Be sure to get
the correct fuse as soon as possible and
return the substitute to its original clip.
It is a good idea to purchase a set of
spare fuses and keep them in your ve-
hicle for emergencies.If the new fuse immediately blows out,
there is a problem with the electrical sys-
tem. Have your Toyota dealer correct it as
soon as possible.
CAUTION
Never use a fuse with a higher am-
perage rating, or any other object, in
place of a fuse. This may cause ex-
tensive damage and possibly a fire.
If any washer does not work or the low
windshield washer fluid level warning
light comes on, the washer tank may be
empty. Add washer fluid.
You may use plain water as washer fluid.
However, in cold areas where tempera-
tures range below the freezing point, use
washer fluid containing antifreeze. This
product is available at your Toyota dealer
and most auto parts stores. Follow the
manufacturer ’s directions for how much to
mix with water.
NOTICE
Do not use engine antifreeze or any
other substitute because it may dam-
age your vehicle’s paint.
Adding washer fluid

’07Camry_U (L/O 0608)
405
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
SPECIFICATIONS
Specifications
Dimensions and weights406 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine406 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel407 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service specifications407 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tires411 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuses412 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 8

’07Camry_U (L/O 0608)
412
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
ENGINE COMPARTMENT
1. RR FOG 10 A: No circuit
2. FR DEF 15 A (2.4 L 4cylinder [2AZ
FE] engine): No circuit
3. AM2 7.5 A: Starting system
4. ALTS 7.5 A: Charging system
5. MAYDAY/TEL 7.5 A: No circuit
6. EACM 10 A (3.5 L V6 [2GRFE] en-
gine): No circuit
7. ETCS 10 A: Electronic throttle control
system
8. HAZ 15 A: Turn signal lights
9. IG2 20 A: Multiport fuel injection sys-
tem/sequential multiport fuel injection
system, starting system, “GAUGE
NO.2” and “IGN” fuses
10. STR LOCK 20 A: Steering lock system
11. DOME 10 A: Gages and meters, vanity
lights, trunk light, ignition switch light,
door courtesy lights, interior light, per-
sonal lights, clock, smart key system
12. ECUB NO.1 10 A: Wireless remote
control system, front passenger occu-
pant classification system, main body
ECU, vehicle stability control system
13. RADIO NO.1 15 A: Audio system, nav-
igation system14. DOOR NO.1 25 A: Main body ECU
15. AMP 25 A: Audio system
16. EFI MAIN 30 A: Multiport fuel injection
system/sequential multiport fuel injec-
tion system, electronic throttle control
system, “EFI NO.2” and “EFI NO.3”
fuses
17. EFI NO.3 10 A: Multiport fuel injection
system/sequential multiport fuel injec-
tion system
18. EFI NO.2 15 A: Multiport fuel injection
system/sequential multiport fuel injec-
tion system
19. SHORN 7.5 A: Horn
20. A/F 20 A: Multiport fuel injection sys-
tem/sequential multiport fuel injection
system
21. MPXB 10 A: Gages and meters
22. EFI NO.1 10 A: Theft deterrent sys-
tem, smart key system, multiport fuel
injection system/sequential multiport
fuel injection system, electronic throttle
control system
23. HORN 10 A: Horns
24. HLP(RL) 15 A: Right−hand headlight
(low beam)
25. HLP(LL) 15 A: Left−hand headlight
(low beam)
Fuses

’07Camry_U (L/O 0608)
413
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
26. HLP(RH) 15 A: Right−hand headlight
(high beam)
27. HLP(LH) 15 A: Left−hand headlight
(high beam)
28. HTR 50 A: Air conditioning system
29. ABS NO.1 50 A: Anti−lock brake sys-
tem, vehicle stability control system,
traction control system, brake assist
system
30. FAN MAIN 50 A (3.5 L V6 [2GRFE]
engine): Electric cooling fans
31. ABS NO.2 30 A: Anti−lock brake sys-
tem, vehicle stability control system,
traction control system, brake assist
system
32. RR DEF 50 A: Rear window defogger,
“MIR HTR” fuse
33. RR PWR SEAT 30 A: No circuit
34. HLP CLN 30 A: No circuit
35. CDS FAN 40 A (2.4 L 4cylinder
[2AZFE] engine): Electric cooling fans
36. RDI FAN 40 A (2.4 L 4cylinder
[2AZFE] engine): Electric cooling fans
37. MSB 30 A: No circuit38. ALT 120 A: “RR FOG”, “FR DEF”,
“AM2”, “ALT−S”, “MAYDAY/TEL”,
“E−ACM”, “ETCS”, “HAZ”, “IG2”, “STR
LOCK”, “DOME”, “ECU−B NO.1”, “RA-
DIO NO.1”, “EFI MAIN”, “AMP”, “DOOR
NO.1”, “EFI NO.3”, “EFI NO.2”, “S−
HORN”, “A/F”, “MPX−B”, “EFI NO.1”,
“HORN”, “H−LP(RL)”, “H−LP(LL)”, “H−
LP(RH)”, “H−LP(LH)”, “HTR”, “ABS
NO.1”, “FAN MAIN”, “ABS NO.2”, “RR
DEF”, “RR PWR SEAT”, “H−LP CLN”,
“CDS FAN”, “RDI FAN”, “MSB”, “ALT”
and “ST/AM2” fuses
39. ST/AM2 30 A: Starting system
INSTRUMENT PANEL
1. RR DOOR RH 25 A: Rear right power
window
2. RR DOOR LH 25 A: Rear left power
window
3. FUEL OPN 7.5 A: No circuit
4. FR FOG 15 A: Front fog lights
5. OBD 7.5 A: On−board diagnosis sys-
tem
6. ECUB NO.2 7.5 A: No circuit