height TOYOTA COROLLA 1996 Owners Manual

38
In the following cases, contact your Toyo-
ta dealer as soon as possible:

The SRS airbag has been inflated.

The front part of the vehicle (shaded in
the illustration) was involved in an ac-
cident not of the extent to cause the
SRS airbag to inflate

The pad section of the steering wheel
(shaded in the illustration) is scratched,
cracked, or otherwise damaged.Toyota strongly urges the use of child
restraint systems for children small
enough to use them.
The laws of all fifty states in the U.S.A.
and Canada now require the use of a child
restraint system.
CAUTION!
For effective protection in automo-
bile accidents and sudden stops,
children must be properly restrained.
Holding a child in your arms is not a
substitute for a child restraint sys-
tem. In an accident, the child can be
crushed against the windshield, or
between you and the vehicle's interi-
or if you are unrestrained.This child restraint is designed for use
only by children who weigh between 9
kg (20 lb.) and 30 kg (66 lb.), whose
height is 127 cm (50 in.) or less, who
are capable of sitting upright alone,
and whose shoulder height is less
than the shoulder belt slots in use.
The child should be one year old or
more and at least 71 cm (28 in.) in
height. It is important to use a rear-
facing child restraint until the child is
about a year old. A rear-facing re-
straint gives the child's head, neck
and body the support they would need
in a crash. See ÐChild restraint sys-
temº in this chapter for more informa-
tion.
If your child's shoulders are above the
upper shoulder belt position, do not
use the built-in child restraint. Your
child should use the vehicle's seat
belts.
This child restraint system conforms to
U.S. Motor Vehicle Safety Standard No.
213 and Canada Motor Vehicle Safety
Standard No. 213.4.
According to accident statistics, children
are safer when properly restrained in the
rear seat than in the front seat.
Child restraintÐ
ÐChild restraint precautionsÐBuilt-in child restraint
ProCarManuals.com

38
In the following cases, contact your Toyo-
ta dealer as soon as possible:

The SRS airbag has been inflated.

The front part of the vehicle (shaded in
the illustration) was involved in an ac-
cident not of the extent to cause the
SRS airbag to inflate

The pad section of the steering wheel
(shaded in the illustration) is scratched,
cracked, or otherwise damaged.Toyota strongly urges the use of child
restraint systems for children small
enough to use them.
The laws of all fifty states in the U.S.A.
and Canada now require the use of a child
restraint system.
CAUTION!
For effective protection in automo-
bile accidents and sudden stops,
children must be properly restrained.
Holding a child in your arms is not a
substitute for a child restraint sys-
tem. In an accident, the child can be
crushed against the windshield, or
between you and the vehicle's interi-
or if you are unrestrained.This child restraint is designed for use
only by children who weigh between 9
kg (20 lb.) and 30 kg (66 lb.), whose
height is 127 cm (50 in.) or less, who
are capable of sitting upright alone,
and whose shoulder height is less
than the shoulder belt slots in use.
The child should be one year old or
more and at least 71 cm (28 in.) in
height. It is important to use a rear-
facing child restraint until the child is
about a year old. A rear-facing re-
straint gives the child's head, neck
and body the support they would need
in a crash. See ÐChild restraint sys-
temº in this chapter for more informa-
tion.
If your child's shoulders are above the
upper shoulder belt position, do not
use the built-in child restraint. Your
child should use the vehicle's seat
belts.
This child restraint system conforms to
U.S. Motor Vehicle Safety Standard No.
213 and Canada Motor Vehicle Safety
Standard No. 213.4.
According to accident statistics, children
are safer when properly restrained in the
rear seat than in the front seat.
Child restraintÐ
ÐChild restraint precautionsÐBuilt-in child restraint
ProCarManuals.com

40
2. While pulling the seat belt release
strap in the child seat cushion, pull
both shoulder belts together.
Pull the seat belt release strap from above
at about 45 angle to the child seat cush-
ion.
If the shoulder belts cannot be pulled out,
return the child seat cushion to an almost
closed position, firmly pull the seat belt re-
lease strap and at the same time pull both
shoulder belts, then lower the child seat
cushion again.3. Compress the shoulder belt clip to
separate the right and left shoulder
belts.4. Add slack to the shoulder belts by
pulling both of them together while
pulling the black seat belt release
strap (see step 4 for illustrated instruc-
tion). Then pull down the seatback
part of the removable pad. Determine
the proper shoulder belt slot height for
your child. Select the slots at or just
above the top of the child's shoulders.
The child seat pad is attached by fastener
tapes.
CAUTION!
If you remove the child seat pad for
cleaning etc., do not use the built-in
child restraint without the pad.
ProCarManuals.com

41
To move the shoulder belts from the lower
slot to the upper slot:
1. Slide the belt up to the top of the seat-
back.
2. Slide the belt down to the outer side of
the upper slot.
3. Squeeze the remaining edge of the
seat belt down into the inner side of the
upper slot.
You may have to push some belt material
through the slot in order to move the belt.
To move the belt to the lower position, re-
verse this procedure.Make sure both belts are adjusted to the
same height.
After moving the shoulder belts, press the
removable pad against the fastener tape
and install the pad to the seatback. Make
sure the belts go through the slots in the
pad that match the shoulder belt slots be-
ing used.
CAUTION!

If your child's shoulders are above
the upper shoulder belt position,
do not use the built-in child re-
straint. Your child should use the
vehicle's seat belts.

Using the vehicle's safety belts on
a child seated on the child restraint
cushion can cause serious injury
to the child in a sudden stop or
crash.

After moving the shoulder belts,
make sure the belts are properly
routed and that they are not twisted
or flipped over.
ProCarManuals.com

84Station swapping: When two FM sta-
tions are close to each other, and an
electronic dead spot, such as is
caused by static or multipath recep-
tion, interrupts the original signal,
sometimes the stronger second signal
is picked up automatically until the
original one returns. This swapping
can also occur as you drive away from
the selected station and approach
another station with a stronger signal.
On models with a power antenna, the an-
tenna automatically extends to its full
height when the radio and ignition are
turned on.
To lower the power antenna, turn off the
audio system by pushing PWR.VOLº, or
turn the ignition key to LOCKº.
On some models, the power antenna au-
tomatically retracts when the radio mode
is switched off to turn on the cassette tape
player.
Before extending the power antenna,
confirm that no one is close enough to get
injured by it.
To prevent damage to the antenna,
make sure it is retracted before
driving your vehicle through an
automatic car wash.
NOTICE
CASSETTE TAPE PLAYER
Use only undamaged cassette tapes of
good quality. Avoid using tapes with a
total playing time longer than 90 min-
utes.
Using damaged tapes will cause trouble
with the tape player. Longer tapes are not
recommended because of their thinness.
Before inserting a cassette, make sure
the tape is not slack and that the label
is firmly stuck on the shell.
Wind the tape firmly by turning the hub
with a pencil or the like.
Be careful not to touch the exposed tape
surface.
When not in use, take the cassette out
of the player, put it back into its case
and store it away from dust, magnets
and direct sunlight.
Leaving cassettes on the dashboard in
the sun could damage your tapes.
Keep the playback head, capstan and
pinch roller clean.
Remove tape coating residue accumu-
lated on the head, capstan and pinch roll-
er once or twice a month. A cleaning tape
is available on the market.
Do not oil any part of the player and
do not insert anything other than
cassette tapes into the slot, or the
tape player may be damaged.
NOTICE
ProCarManuals.com

11 0

Even if the power assist is com-
pletely lost, the brakes will still
work. But you will have to push the
pedal hardÐmuch harder than nor-
mal. And your braking distance will
be longer.
ANTI-LOCK BRAKE SYSTEM (vehicles
with ABSº warning light)
The anti-lock brake system is designed to
prevent lock-up of the wheels during sud-
den braking or braking on slippery road
surfaces. This assists the driver in con-
trolling the vehicle under these circum-
stances.
The anti-lock brake system becomes op-
erative after the vehicle has accelerated
to a speed in excess of approximately 10
km/h (6 mph). It stops operating when the
vehicle decelerates to a speed below
approximately 5 km/h (3 mph).
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
is started. This means that the anti-lock
brake system is in the self check mode,
and does not indicate a malfunction.When the anti-lock brake system function
is in action, you may feel the brake pedal
pulsating and hear a noise. In this situa-
tion, to let the anti-lock brake system
work for you, just hold the brake pedal
down more firmly. Do not pump the brake.
The brake pedal pulsation caused by the
anti-lock brake system may indicate haz-
ardous road surface conditions. Although
the anti-lock brake system assists in pro-
viding vehicle control, it is still important to
drive with all due care, because the anti-
lock brake system cannot overcome the
laws of physics that act on your vehicle:

Braking capability is dependent on tire
friction with the road surface.

Even though the anti-lock brake sys-
tem is operating, a driver cannot main-
tain full control on certain slippery road
surfaces, when cornering at high
speeds, or in violent maneuvers.

Avoid high speeds on wet roads. The
anti-lock brake system cannot elimi-
nate the risk of hydroplaning and loss
of tire friction.Always maintain a safe distance from the
vehicle in front of you. Compared with ve-
hicles not fitted with an anti-lock brake
system, your vehicle may require a longer
stopping distance in the following cases:

Driving on rough, gravel or snow-cov-
ered roads.

Driving with tire chains installed.

Driving on roads where the road sur-
face is pitted or has other differences
in surface height.
ProCarManuals.com

Part 3
How to start the engineÐ
(a) Before cranking Before starting the engine
11 5
STARTING AND
DRIVING

Before starting the engine

How to start the engine

Tips for driving in various
conditions

Winter driving tips

Trailer towing

How to save fuel and make your
vehicle last longer, too
1. Check the area around the vehicle be-
fore entering it.
2. Adjust seat position, seatback angle,
head restraint height and steering wheel
angle.
3. Adjust inside and outside rear view
mirrors.
4. Lock all doors.
5. Fasten seat belts.1. Apply the parking brake firmly.
2. Turn off unnecessary lights and acces-
sories.
3.Manual transmission: Press the
clutch pedal to the floor and shift the
transmission into neutral. Hold the clutch
pedal to the floor until the engine is
started. A starter safety device will pre-
vent the starter from operating if the
clutch pedal is not fully depressed.
Automatic transmission: Put the selec-
tor lever in Pº. If you need to restart the
engine while the vehicle is moving, put the
selector lever in Nº. A starter safety de-
vice will prevent the starter from operating
if the selector lever is in any drive position.
4.Automatic transmission only: De-
press the brake pedal and hold it to the
floor until driving off.
ProCarManuals.com

162
CAUTION!
Do not drive with the snow tires in-
correctly inflated.
Never drive over 120 km/h (75 mph)
with any type of snow tires.
TIRE CHAIN SELECTION
Use the tire chains of correct size and
type.
Use SAE Class Sº type radial tire chains
except radial cable chains or V-bar type
chains.
Regulations regarding the use of tire
chains vary according to location or
type of road, so always check them be-
fore installing chains.
CHAIN INSTALLATION
Install the chains on the front tires as
tightly as possible. Do not use tire
chains on the rear tires. Retighten
chains after driving 0.5'1.0 km
(1/4'1/2 mile).
When installing chains on your tires, care-
fully follow the instructions of the chain
manufacturer.
If wheel covers are used, they will be
scratched by the chain band, so remove
the covers before putting on the chains.
CAUTION!
Do not exceed 50 km/h (30 mph) or
the chain manufacturer's recom-
mended speed limit, whichever is
lower.
Drive carefully avoiding bumps,
holes, and sharp turns, which may
cause the vehicle to bounce.
Avoid sharp turns or locked-wheel
braking, as use of chains may ad-
versely affect vehicle handling.
Do not attempt to use a tire chain on
the compact spare tire, as it may
result in damage to the vehicle as
well as the tire.
NOTICE
WHEN TO REPLACE YOUR WHEELS
If you have wheel damage such as
bending, cracks or heavy corrosion,
the wheel should be replaced.
If you fail to replace damaged wheels, the
tire may slip off the wheel or they may
cause loss of handling control.
WHEEL SELECTION
When replacing wheels, care should
be taken to ensure that the wheels are
replaced by ones with the same load
capacity, diameter, rim width, and off-
set.
This must be observed on compact spare
tires, too.
Correct replacement wheels are available
at your Toyota dealer.
A wheel of a different size or type may ad-
versely affect handling, wheel and bearing
life, brake cooling, speedometer/odometer
calibration, stopping ability, headlight aim,
bumper height, vehicle ground clearance,
and tire or snow chain clearance to the
body and chassis.
Replacing wheels
ProCarManuals.com

Part 8Dimensions and weight
181
SPECIFICATIONS

Dimensions and weight

Engine

Fuel

Service specifications

Tires

Fuses
Overall length mm (in.)
Overall width mm (in.)
Overall height mm (in.)
mm (in.)
Wheelbase mm (in.)
Front tread mm (in.)
Rear tread mm (in.)
Vehicle capacity weight
(occupants + luggage) kg (lb.)
*
1: Unladen vehicle plus two occupants
*
2: Unladen vehicleSedan Wagon
4370 (172.0) 4370 (172.0)
1685 ( 66.3) 1685 ( 66.3)
1360 ( 53.5)*
11405 ( 55.3)*1
1380 ( 54.3)*21425 ( 56.1)*2
2465 (97.0) 2465 (97.0)
1460 ( 57.5) 1460 ( 57.5)
1450 ( 57.1) 1450 ( 57.1)
385 (850) 385 (850)
ProCarManuals.com