roof TOYOTA LAND CRUISER 1986 Factory Owner's Manual

BO1KR-01
- BODYROOF HEADLINING
BO-101
2675 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSTALLATION
Installation is in the reverse order of removal (See page BO-97).

BO4IZ-01
H05257
: 5 Clips
H05258
H05259
H07941
11 Clips
- BODYROOF HEADLINING
BO-97
2671 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE ROOF HEADLINING REAR TRIM
Using a screwdriver, remove the roof headlining rear trim.
HINT:
Tape up the screwdriver tip before use.
2. REMOVE REAR NO. 2 SEATS
3. REMOVE REAR MAT SET PLATE
(a) Remove the 5 screws.
(b) Using a screwdriver, remove the rear mat set plate.
HINT:
Tape up the screwdriver tip before use.
4. REMOVE STRIKER PLATES
(a) Remove the 6 screws.
(b) Using a screwdriver, remove the striker plates.
HINT:
Tape up the screwdriver tip before use.
5. REMOVE REAR MAT
6. REMOVE REAR NO. 2 SEAT OUTER BELT FLOOR AN-
CHOR
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
7. REMOVE REAR NO. 1 SEAT OUTER BELT FLOOR AN-
CHOR
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
8. REMOVE REAR DOOR SCUFF PLATES
9. REMOVE REAR DOOR OPENING TRIMS
10. REMOVE QUARTER TRIM PANEL LH
(a) Remove the quarter trim jack cover.
(b) Using a clip remover, remove the 2 clips.
(c) Remove the quarter trim panel LH, then disconnect the
connector.

H18922
10 Clips
H18906
: 9 Clips
H18904
H05264
Claw
BO-98
- BODYROOF HEADLINING
2672 Author
: Date
:
2004 LAND CRUISER (RM1071U)
11. REMOVE QUARTER TRIM PANEL RH
(a) Using a clip remover, remove the clip.
(b) Remove the quarter trim panel RH.
12. REMOVE REAR NO. 2 SEAT OUTER BELT SHOUL-
DER ANCHORS
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
13. REMOVE REAR NO. 1 SEAT OUTER BELT SHOUL-
DER ANCHORS
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
14. REMOVE UPPER ROOF SIDE INNER GARNISHES
(a) Using a screwdriver, remove the 2 assist grip plugs, then
remove the 2 screws and the assist grip.
HINT:
Tape up the screwdriver tip before use.
(b) Using a clip remover, remove the clip.
(c) Using a screwdriver, remove the upper roof side inner gar-
nish.
HINT:
Tape up the screwdriver tip before use.
(d) Use the same manner described above to the other side.
15. REMOVE FRONT DOOR SCUFF PLATES
16. REMOVE COWL SIDE TRIMS
17. REMOVE FRONT DOOR OPENING TRIMS
18. REMOVE FRONT ASSIST GRIP
(a) Using a screwdriver, remove the 2 assist grip plugs, then
remove the 2 screws and front assist grip.
HINT:
Tape up the screwdriver tip before use.
(b) Use the same manner described above to the other side.
19. REMOVE FRONT PILLAR GARNISH
(a) Using a screwdriver, remove the front pillar garnish.
HINT:
Tape up the screwdriver tip before use.
(b) Use the same manner described above to the other side.
20. REMOVE CENTER PILLAR LOWER GARNISH
(a) Using a screwdriver, remove the center pillar garnish cov-
er.
HINT:
Tape up the screwdriver tip before use.

H05265
: 4 Clips
H21424
w/ Curtain Shield Airbag
w/o Curtain Shield Airbag
H21425
w/ Curtain Shield Airbag
w/o Curtain Shield Airbag
- BODYROOF HEADLINING
BO-99
2673 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(b) Using a screwdriver, remove the center pillar lower gar-
nish as shown in the illustration.
HINT:
Tape up the screwdriver tip before use.
(c) Use the same manner described above to the other side.
21. REMOVE CENTER PILLAR GARNISH
(a) Using a screwdriver, remove the seat belt anchor cover
cap.
HINT:
Tape up the screwdriver tip before use.
(b) Remove the bolt and the front seat outer belt shoulder an-
chor.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
(c) Using a clip remover, remove the clip.
(d) Using a screwdriver, remove the center pillar garnish.
HINT:
Tape up the screwdriver tip before use.
(e) Use the same manner described above to the other side.
22. REMOVE SUN VISOR
(a) Using a screwdriver, remove the caps.
HINT:
Tape the screwdriver tip before use.
(b) Remove the screws, then disconnect the connectors.
(c) Remove the sun visors.
23. REMOVE DOUBLE VISOR
Remove the screws and the double visors.
24. REMOVE HOLDER
Remove the screws and the holders.

H05268
H05270
H21423
4 Clips
H18926
BO-100
- BODYROOF HEADLINING
2674 Author
: Date
:
2004 LAND CRUISER (RM1071U)
25. REMOVE DOME LIGHT
(a) Using a screwdriver, remove the lens as shown in the il-
lustration.
HINT:
Tape up the screwdriver tip before use.
(b) Remove the 4 screws and the dome light, then disconnect
the connector.
26. REMOVE MAP LAMP
(a) Using a screwdriver, remove the lens as shown in the il-
lustration.
HINT:
Tape up the screwdriver tip before use.
(b) Remove the 4 screws and the map lamp, then disconnect
the connector.
27. REMOVE OVERHEAD CONSOLE BOX
(a) Remove the bolt.
(b) Using a screwdriver, remove the overhead console box,
then disconnect the connector.
HINT:
Tape up the screwdriver tip before use.
28. REMOVE REAR A/C CONTROL PANEL
Using a screwdriver, release the 4 claws and pull out the rear
A/C control panel, then disconnect the connector.
HINT:
Tape up the screwdriver tip before use.
29. REMOVE ROOM TEMPERATURE SENSOR
Using a scrwedriver, pull out the room temperature sensor, then
disconnect the connector.
HINT:
Tape up the screwdriver tip before use.
30. REMOVE ASSIST GRIPS
31. w/o Curtain Shield Airbag:
REMOVE CENTER ASSIST GRIPS
32. REMOVE ROOF HEADLINING
Using a clip remover, remove the 3 clips and the roof headlining.
33. REMOVE REAR A/C REGISTER
34. w/ Curtain Shield Airbag:
REMOVE ADJUSTABLE ANCHOR
Remove the 2 bolts and the adjustable anchor.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
35. w/ Curtain Shield Airbag:
REMOVE CENTER ASSIST GRIPS

H18931
Upper Roof Side
Inner Garnish
Quarter Trim Panel
Assist Grip
Roof Headlining
Rear Trim Rear Door Scuff Plate
Rear Mat Set Plate
Rear No. 2 Lap
Type Center with
Inner Belt
Rear No. 2 Seat
Inner Belt
Rear No. 1 Seat
Inner BeltRear No. 2 Seat
Outer Belt
Rear Seat Shoulder
Belt Cover Rear Seat Shoulder
Belt Guide
Rear No. 1 Seat Outer
Center BeltRear No. 1 Seat
Outer Belt
: Specified torqueN´m (kgf´cm, ft´lbf)Rear No. 1 Seat
Inner Belt
Adjustable Anchor
42 (430, 31)
42 (430, 31)
Rear Seat Belt:
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
27 (275, 20)
CRS Tether Anchor
BracketCRS Tether Anchor
Bracket Cover
42 (430, 31)3.9 (40, 35 in.´lbf)
Assist Grip Plug
42 (430, 31)
BO-138
- BODYSEAT BELT
2712 Author
: Date
:
2004 LAND CRUISER (RM1071U)

BO1KH-02
H05288
H05706
H05708
BO3396
H05296
BO-78
- BODYSLIDING ROOF
2652 Author
: Date
:
2004 LAND CRUISER (RM1071U)
ADJUSTMENT
1. REMOVE SIDE GARNISH
Before making adjustment, using a screwdriver, remove the
side garnishes.
HINT:

Tape the screwdriver tip before use.

After adjustment, reinstall the side garnishes.
2. ADJUST SLIDING ROOF GLASS IN FORWARD/REAR-
WARD AND LEFT/RIGHT DIRECTIONS
(a) Loosen the sliding roof glass installation nuts.
(b) Adjust the sliding roof glass forward/rearward or left/right.
3. ADJUST SLIDING ROOF GLASS IN UPWARD OR
DOWNWARD DIRECTIONS
(a) Loosen the screws shown in the illustration.
(b) Adjust the sliding roof glass upward or downward.
4. ADJUST SLIDING ROOF GLASS IN CLEARANCE
(Difference in left and right clearance)
(a) When the front or rear alignment is not correct, remove
the drive gear and sliding roof glass, then adjust the drive
cables.
NOTICE:
Remove the drive gear with the sliding roof fully closed.
(b) Adjust by sliding the cables forward or rearward to align
the 2 marks as shown.
(c) Install the drive gear and sliding roof glass.

BO1KE-02
H05287
Side Garnish
Rear Garnish Sliding Roof Glass
Front Garnish
Side GarnishSunshade Trim
Rear Drip Channel Sliding Roof Housing
Drive Cable Guide Block Cable Guide Casing
Wind Deflector Panel
Drive GearSliding Roof
Panel Stopper Sliding Roof
Guide Rail
Drive Cable
- BODYSLIDING ROOF
BO-73
2647 Author
: Date
:
2004 LAND CRUISER (RM1071U)
COMPONENTS

BO1KG-02
H05293
H05294
H05295
H05296
H05297
BO-76
- BODYSLIDING ROOF
2650 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DISASSEMBLY
1. REMOVE REAR DRIP CHANNEL
(a) Using a screwdriver, remove the front side of rear drip
channel.
HINT:
Tape the screwdriver tip before use.
(b) Remove the rear drip channel as shown in the illustration.
2. REMOVE SLIDING ROOF PANEL STOPPERS
Remove the 2 screws and 2 stoppers.
3. REMOVE SUNSHADE TRIM
4. REMOVE DRIVE CABLE
(a) Remove the screw and guide rail stopper.
(b) Slide the drive cable rearward, then remove it.
HINT:
At the time of reassembly, please refer to the following items.

Adjust the drive cable to a closed and tilted down position.

Slide the cable forward or backward to align the 2 marks
as shown.

Slide the cable to the forefront with your hand.
(c) Employ the same manner described above to the other
side.
5. REMOVE WIND DEFLECTOR PANEL
Remove the 2 screws and wind deflector panel as shown in the
illustration.

H05298
H05299
- BODYSLIDING ROOF
BO-77
2651 Author
: Date
:
2004 LAND CRUISER (RM1071U)
6. REMOVE GUIDE BLOCK
(a) Remove the 2 screws and guide block.
(b) Employ the same manner described above to the other
side.
7. REMOVE SLIDING ROOF HOUSING
Remove the 6 screws and sliding roof housing.
8. REMOVE CABLE GUIDE CASING