TOYOTA LAND CRUISER 1998 Factory Repair Manual
Page 1511 of 3115
AB0119H19232
H21268
H21136
D Squib
D+ u"
(-) (+) ON
Column Wire
Airbag
Sensor
AssemblySpiral
Cable
AB0119H16857
H21269
H21137
D Squibu"
ON Column Wire
(+) (-)D+ Dash Wire
Airbag
Sensor
AssemblySpiral
Cable
DI-730
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
923 Author: Date:
2004 LAND CRUISER (RM1071U)
5 Check spiral cable.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the spiral cable connector from the column
wire.
CHECK:
(a) Turn the ignition switch to ON.
(b) Measure the voltage between the body ground and D+ of
the orange spiral cable connector on the steering wheel
pad (D squib) side.
OK:
Voltage: Below 1 V
NG Replace spiral cable.
OK
6 Check column wire.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the column wire connector from the dash
wire.
CHECK:
(a) Turn the ignition switch to ON.
(b) Measure the voltage between the body ground and D+ of
the column wire connector on the spiral cable side.
OK:
Voltage: Below 1 V
NG Repair or replace column wire.
OK
Page 1512 of 3115
AB0119H16857
H21760H21138
D Squib
D+
(-) (+) ON Column Wire
Dash Wire
Airbag
Sensor
AssemblySpiral
Cable
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-731
924 Author: Date:
2004 LAND CRUISER (RM1071U)
7 Check dash wire.
CHECK:
(a) Turn the ignition switch to ON.
(b) Measure the voltage between the body ground and D+ of
the dash wire connector on the column wire side.
OK:
Voltage: Below 1 V
NG Repair or replace dash wire.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check. If the malfunctioning part can not be
detected by the simulation method, replace all SRS components including the wire harness.
Page 1513 of 3115
H01454
A27
P Squib
10Airbag Sensor Assembly
2Y-R
C26
Y-G 1
11P+
P-
C26 DI-732
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
925 Author: Date:
2004 LAND CRUISER (RM1071U)
DTC B0105/53 Short in P Squib Circuit
CIRCUIT DESCRIPTION
The P squib circuit consists of the airbag sensor assembly and the front passenger airbag assembly.
It causes the SRS to deploy when the SRS deployment conditions are satisfied.
For details of the function of each component, see OPERATION on page RS-3.
DTC B0105/53 is recorded when a short is detected in the P squib circuit.
DTC No.DTC Detecting ConditionTrouble Area
B0105/53
Short in P squib circuit
P squib malfunction
Airbag sensor assembly malfunctionFront passenger airbag assembly (P squib)
Airbag sensor assembly
Dash wire
WIRING DIAGRAM
DI6P7-26
Page 1514 of 3115
R14286H16854H17088
P Squib
Airbag
Sensor
Assembly
P+ P-
(-)
(+)
Dash Wire
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-733
926 Author: Date:
2004 LAND CRUISER (RM1071U)
INSPECTION PROCEDURE
1 Prepare for inspection (See step 1 on page DI-923).
2 Check dash wire (P squib circuit).
PREPARATION:
Release the airbag activation prevention mechanism built in the
connector of the dash wire on the airbag sensor assembly side
(See page DI-692).
CHECK:
Measure the resistance between P+ and P- of the dash wire
connector on the front passenger airbag assembly (P squib)
side.
OK:
Resistance: 1 MW or Higher
NG Repair or replace dash wire.
OK
Page 1515 of 3115
H01023AB0119H01077 H10600H10611
P Squib
Airbag
Sensor
Assembly
DTC B0105/53
DLC3
ON" u
TC CG
DI-734
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
927 Author: Date:
2004 LAND CRUISER (RM1071U)
3 Check airbag sensor assembly.
PREPARATION:
(a) Connect the connector to the airbag sensor assembly.
(b) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0105/53 is not output.
HINT:
Codes other than code B0105/53 may be output at this time, but
they are not relevant to this check.
NG Replace airbag sensor assembly.
OK
Page 1516 of 3115
H01024AB0119H01077
H10600H10612
"u
ON
DTC B0105/53 DLC3Airbag
Sensor
Assembly P Squib
TC CG
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-735
928 Author: Date:
2004 LAND CRUISER (RM1071U)
4 Check P squib.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the front passenger airbag assembly (P squib)
connector.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0105/53 is not output.
HINT:
Codes other than code B0105/53 may be output at this time, but
they are not relevant to this check.
NG Replace front passenger airbag assembly
(P squib).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.
Page 1517 of 3115
R14286H16854H17088
P Squib
Airbag
Sensor
Assembly
P+ P-
(-)(+)
Dash Wire
DI-736
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
929 Author: Date:
2004 LAND CRUISER (RM1071U)
DTC B0106/54 Open in P Squib Circuit
CIRCUIT DESCRIPTION
The P squib circuit consists of the airbag sensor assembly and the front passenger airbag assembly.
It causes the SRS to deploy when the SRS deployment conditions are satisfied.
For details of the function of each component, see OPERATION on page RS-3.
DTC B0106/54 is recorded when an open is detected in the P squib circuit.
DTC No.DTC Detecting ConditionTrouble Area
B0106/54
Open in P squib circuit
P squib malfunction
Airbag sensor assembly malfunctionFront passenger airbag assembly (P squib)
Airbag sensor assembly
Dash wire
WIRING DIAGRAM
See page DI-732.
INSPECTION PROCEDURE
1 Prepare for inspection (See step 1 on page DI-923).
2 Check dash wire (P squib circuit).
CHECK:
Measure the resistance between P+ and P- of the dash wire
connector on the front passenger airbag assembly (P squib)
side.
OK:
Resistance: Below 1 W
NG Repair or replace dash wire.
OK
DI6P8-14
Page 1518 of 3115
H01023AB0119H01078 H10600H16855H17089
P Squib
Airbag
Sensor
Assembly
P+
P-
DTC B0106/54 DLC3
ON " u
TC CG
Dash Wire
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-737
930 Author: Date:
2004 LAND CRUISER (RM1071U)
3 Check airbag sensor assembly.
PREPARATION:
(a) Connect the connector to the airbag sensor assembly.
(b) Using a service wire, connect P+ and P- of the dash wire
connector on the front passenger airbag assembly (P
squib) side.
(c) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0106/54 is not output.
HINT:
Codes other than code B0106/54 may be output at this time, but
they are not relevant to this check.
NG Replace airbag sensor assembly.
OK
Page 1519 of 3115
H01024AB0119H01078 H10600H10614
"u
ON
DTC B0106/54
DLC3Airbag
Sensor
Assembly P Squib
TC CG
DI-738
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
931 Author: Date:
2004 LAND CRUISER (RM1071U)
4 Check P squib.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the front passenger airbag assembly (P squib)
connector.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0106/54 is not output.
HINT:
Codes other than code B0106/54 may be output at this time, but
they are not relevant to this check.
NG Replace front passenger airbag assembly
(P squib).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.
Page 1520 of 3115
H01227H16856H17090
P Squib
Airbag
Sensor
Assembly
(+) (-)P+
Dash Wire
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-739
932 Author: Date:
2004 LAND CRUISER (RM1071U)
DTC B0107/51 Short in P Squib Circuit (to Ground)
CIRCUIT DESCRIPTION
The P squib circuit consists of the airbag sensor assembly and the front passenger airbag assembly.
It causes the SRS to deploy when the SRS deployment conditions are satisfied.
For details of the function of each component, see OPERATION on page RS-3.
DTC B0107/51 is recorded when ground short is detected in the P squib circuit.
DTC No.DTC Detecting ConditionTrouble Area
B0107/51
Short in P squib circuit (to ground)
P squib malfunction
Airbag sensor assembly malfunctionFront passenger airbag assembly (P squib)
Airbag sensor assembly
Dash wire
WIRING DIAGRAM
See page DI-732.
INSPECTION PROCEDURE
1 Prepare for inspection (See step 1 on page DI-923).
2 Check dash wire (P squib circuit).
CHECK:
Measure the resistance between the body ground and P+ of the
dash wire connector on the front passenger airbag assembly (P
squib) side.
OK:
Resistance: 1 MW or Higher
NG Repair or replace dash wire.
OK
DI6P9-14