audio TOYOTA LAND CRUISER 2005 J100 Navigation Manual

155
(h) If the satellite radio tuner malfunctions
When problems occur with the XM tuner, a message will appear on the display. Referring to the table below to identify the problem, take the sug-
gested corrective action.
ANTENNA
The XM antenna is not connected. Check whether the XM antenna cable is attached securely.
A short−circuit occurs in the antenna or the surrounding antenna cable. See a Toyota certified dealer.
UPDATING
You have not subscribed to the XM satellite radio. The radio is being updated with the latest encryption
code. Contact the XM satellite radio for subscription information. When a contact is canceled, you can
choose the “CH000” and all free−to−air channels.
The premium channel you selected is not authorized. Wait for about 2 seconds until the radio returns to
the previous channel or “CH001”. If it does not change automatically, select another channel. If you want
to listen to the premium channel, contact the XM satellite radio.
NO SIGNALThe XM signal is too weak at the current location. Wait until your vehicle reaches a location with a stron-
ger signal.
LOADINGThe unit is acquiring audio or program information. Wait until the unit has received the information.
OFF AIRThe channel you selected is not broadcasting any programming. Select another channel.
−−−−−There is no song/program title or artist name/feature associated with the channel at that time. No action
needed.
−−−The channel you selected is no longer available. Wait for about 2 seconds until the radio returns to the
previous channel or “CH001”. If it does not change automatically, select another channel.
The XM Listener Care Center is also available on the phone, please call (800) 852−9696 during the following hours:
Monday – Saturday: 7 a.m. – 1 a.m. Sunday: 12 p.m – 12 a.m.
VI

156
NOTICE
This equipment has been tested and
found to comply with the limits for a
class B digital device, pursuant to Part
15 of the FCC Rules. These limits are de-
signed to provide reasonable protection
against harmful interference in a resi-
dential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed
and used in accordance with the in-
structions, may cause harmful interfer-
ence to radio communications. Howev-
er, there is no guarantee that interfer-
ence will not occur in a particular instal-
lation.
If this equipment does cause harmful in-
terference to radio or television recep-
tion, which can be determined by turn-
ing the equipment off and on, the user is
encouraged to try to correct the interfer-
ence by one or more of the following
measures:
– Reorient or relocate the receiving an-
tenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
– Consult the dealer or an experienced
radio/TV technician for help.
Information to user
Alternation or modifications carried out
without appropriate authorization may
invalidate the user’s right to operate the
equipment.NOTICE
This XM tuner supports “Audio Ser-
vices” (Music and Talk) of only XM satel-
lite radio and “Text Information”, linked
to the respective “Audio Services”.
*Text Information includes, Station
Name, (Artist) Name, (Song) Title and
Category Name.

159
If you set “REW 1”, the player will rewind
to the beginning of the current program.
When counting the number of programs
you want to rewind, remember to count the
current program as well. For example, if
you want to rewind to a song that is two be-
fore the song you are listening to, push this
button until “REW 3” appears on the dis-
play.
When the beginning of the tape is reached,
the player automatically resumes normal
play.
There must be at least 5 seconds of blank
space between programs for this feature to
work correctly.
“RPT”, “SKIP” or “Automatic program
selection” features: These features may
not work well with some spoken word, live or
classical recordings.
DVD player operation
The DVD player can play audio CDs, DVD
video discs and video CDs.
For appropriate discs for this paper, see “Car
audio/video system operating hints” on page
175.
For safety reasons, you can enjoy DVD video
discs and video CDs only when the vehicle is
completely stopped with the ignition switch in
the “ACC” or “ON” position and the parking
brake applied. While you are driving, you can
hear audio alone even in the DVD video or
video CD mode.
The DVD player can play the discs labeled as
shown below.
(a) Inserting discs
unx604
1. Pull the lock release lever and open the
console box.
unx605
2. Push this button to eject the magazine.
VI

160
unx606
3. Pull out the tray while pushing the lock
release button.
unx607
4. Put a disc on the tray with its label face
up and push the tray back into the maga-
zine.If the label faces down, the disc cannot be
played. In this case, “DISC CHECK” and disc
number appears on the display.
If a disc which is not playable is inserted,
“DISC CHECK” will also appear on the
screen. For appropriate discs for this player,
see “Car audio/video system operating hints”
on page 175.
unx608a
5. Insert the magazine into the player as
indicated by the arrow ahead on the maga-
zine, close the door and console box.When the magazine is set completely, the
system will be in a “Load” cycle for approxi-
mately 30 seconds while the system
searches for discs in the magazine. Upon
completion of this cycle, the DVD player unit
will be ready to play. If the “DISC” button is
pushed during the “Load” cycle, “LOAD” ap-
pears on the display until the system has
completed the load cycle, after which the sys-
tem will begin normal play.
CAUTION
To reduce the chance of injury in case of
an accident or a sudden stop, always
keep the console box closed while driv-
ing.

161
(b) Playing a disc
ung627
Push the “DISC” button if the magazine is
already loaded in the player.
The “DVD CHANGER” screen appears on the
display.
The discs set in the magazine are played con-
tinuously, starting with disc number 1. The
disc number of the disc currently being
played, the track number and the time from
the beginning of the program are shown on
the display.
(c) Selecting a desired disc
On the screen: Touch the desired disc
number.
The selected disc number is highlighted in
green.
The player will start playing the selected disc
from the first track.
On the audio panel: Push the “
” or “”
side of the “DISC” button.
When you release the button, the player will
start playing the selected disc from the first
track.
(d) Operating an audio CD
(i) Playing an audio CD
lxb008a
Push the “AUDIO” button to display this
screen. You can operate the switches and
choose the number of the disc you want to
play. The selected disc is automatically
played.
VI

162 (ii) Selecting a desired track
“TRACK” button: Use for direct access to a
desired track.
Push either side of the “TRACK” button and
hold it until the desired track number appears
on the display. As you release the button, the
player will start playing the selected track from
the beginning.
Fast forward: Touch the “
” switch and
hold it to fast forward the disc. When you re-
lease the switch, the player will resume play-
ing from that position.
Reverse: Touch the “
” switch and hold it
to reverse the disc. When you release the
switch, the player will resume playing.(iii) Searching for a desired track or a disc
lxb008a
Touch the “SCAN” switch.
“Scan” will be highlighted in green. The player
will play the next track for 10 seconds, then
scan again. To select a track, touch the
“SCAN” switch a second time. If the player
reaches the end of the disc, it will continue
scanning at track 1.
After all the tracks are scanned in one pass,
normal play resumes.
Touch the “DISK SCAN” switch.
“DISC SCAN” will be highlighted in green.
The program at the beginning of each disc will
be played for 10 seconds. To continue listen-
ing to the program of your choice, touch the
“DISC SCAN” switch a second time.
After all the audio disc are scanned in one
pass, normal play resumes.(iv) Other functions
lxb006a
“RPT” switch: Use it for automatic repeat of
the track you are currently listening to.
Touch the switch while the track is playing.
When the track is finished, the player will auto-
matically go back to the beginning of the track
and play the track again. To cancel it, touch
the switch once again.
“DISC RPT” switch: Use it for automatic re-
peat of the disc you are currently listening to.
Touch the switch while the disc is playing.
When the disc is finished, the player will auto-
matically go back to the beginning of the disc
and play the disc again. To cancel it, touch the
switch once again.

163 “RAND” switch: Use it for automatic and
random selection of the disc which you are
currently listening to.
When the switch is touched, the system se-
lects a track in the disc you are currently lis-
tening to. To cancel it, touch the switch once
again.
“DISC RAND” switch: Use it for automatic
track selection for all the audio discs and play
by the system.
When the switch is touched, the system se-
lects a track in all the audio discs in the maga-
zine which is set and plays it. To cancel it,
touch the switch once again.
“TITLE” switch: Use it for displaying the
song title and track number while the CD−
TEXT disc is playing.
The switch is not displayed on the screen
while the CD−TEXT disc is not playing. Up to
29 letters can be displayed. To cancel it,
touch the “TITLE OFF” switch.
(e) Operating a DVD video disc
NOTE: The playback condition of some
DVD video discs may be determined by a
DVD video software producer. This DVD
player plays a disc as the software produc-
er intended. So some functions may not
work properly. Be sure to read the instruc-
tion manual for the DVD video disc sepa-
rately provided. For the detailed informa-
tion about DVD video discs, see “(h) DVD
player and DVD video disc information”Precautions on DVD video disc
When recording with a DVD video or video
CD, audio tracks may not record in some
cases while the menu is displayed. As audio
will not play in this case, verify that the video
tracks are playing and then activate playback.
When playback of a disc is completed:
If an audio CD is playing, the next CD will
be selected and playback will begin auto-
matically.
If a DVD video or video CD is playing, play-
back will stop or the menu screen will be
displayed. The next disc will not play back
automatically. (Audio tracks cannot be
heard while the disc is stopped)
The title/chapter number and playback time
display may not appear while playing back
certain DVD video discs.
VI

164
CAUTION
Conversational speech on some DVDs
is recorded at a low volume to empha-
size the impact of sound effects. If you
adjust the volume assuming that the
conversations represent the maximum
volume level that the DVD will play, you
may be startled by louder sound effects
or when you change to a different audio
source. The louder sounds may have a
significant impact on the human body or
pose a driving hazard. Keep this in mind
when you adjust the volume.
The “DVD Hint !” screen appears when the
video screen is first displayed after you
turn the ignition key to “ACC” or “ON”.
Touch the “OK” switch when you read the
message.(i) Playing a DVD video disc
lxb009a
Push the “AUDIO” button to display this
screen. You can operate the switches and
choose the number of the disc you want to
play. The selected disc is automatically
played.
When you touch the “WIDE MODE” switch,
the screen mode can be changed.
When you touch the “PICTURE” switch, the
video screen returns.

166
Switches on second page
“Set Up” switch: The initial set up screen
appears. (See page 168.)
“Search” switch: The title search screen
appears. (See page 166.)
“Return” switch: Use this switch to display
the predetermined scene and start playing
from there.
“Audio” switch: The audio changing screen
appears. (See page 167.)
“Sub Title” switch: The subtitle changing
screen appears. (See page 167.)
“Angle” switch: The angle selection screen
appears. (See page 167.)(iv) Selecting a menu item
Enter the menu item using “ ”, “”, “
”
or “” switches and touch “Enter”. The
player starts playing video for that menu
item. (For details, see the manual that
comes with the DVD video disc provided
separately.)
Each you push “Move Buttons” switch,
the switches on the screen move upward
and downward.
When you push “OFF” switch, the displayed
switches do not display. To display them
again, push “ON” switch.
Touch “Back”, the previous screen returns.(v) Searching by titleEnter the title number using “–”, “+” and
“+10” switches and touch “Enter”. The
player starts playing video for that title
number.
When you push “
” or “” on the “TRACK”
switch, you can select a chapter.
Touch “Back”, and the previous screen re-
turns.

167 (vi) Changing the subtitle language
Each time you touch “Sub title”, the lan-
guage is selected from the ones stored in
the discs and changed.
To turn off the subtitle, touch “Hide”.
Touch “Back”, and the previous screen re-
turns.(vii) Changing the audio languageEach time you touch “Audio”, the lan-
guage is selected from the ones stored in
the discs and changed.
Touch “Back”, and the previous screen re-
turns.(viii) Changing the angleThe angle can be selected for discs that
are multiangle compatible when the
angle mark appears on the display.
Each time you touch “Angle”, the angle
changes.
Touch “Back”, and the previous screen re-
turns.
VI