display TOYOTA LAND CRUISER 2006 J100 Navigation Manual

11 5
You can change the Device Name and
Passkey.
BD_ADDR is Bluetooth device address. Do
not change the Device Name to the same
name as the one of the other Bluetooth
phones. They cannot be identified.
BD_ADDR is different depending on the
system. You can confirm the address
when it cannot be identified.(i) Change the Device Name
You can change the Device Name to the
desired one from the name already regis-
tered in the system.
Touch the “Change” of Device Name to
display the “Device Name List” screen.
Select the desired name and touch “OK”. (ii) Change the Passkey
The Passkey in the system is initially fixed.
You can change the Passkey within 48
figures.
Touch the “Change” of Passkey to dis-
play “Enter Bluetooth Passkey” screen.

11 6
Touch the desired key to input the Pass-
key.
Each time you touch
“”, an inputted num-
ber is deleted.
Touch
“Enter”.
(c) Delete the Bluetooth phone
1. Touch the “Settings” switch to dis-
play “Settings” screen.
2. Touch the “Delete” switch to display
“Delete Telephone” screen. You can de-
lete the Bluetooth phone which you regis-
tered.
Select the desired phone from the list and
touch
“OK”.

11 7
(d) Call on the Bluetooth phone
After you enter the Bluetooth phone, you
can call by using handsfree system. This
system has 6 methods below by which
you call.
(i) By dial
You can call by inputting the telephone
number.
This cannot be operated while you are driv-
ing.
Touch the desired key to input the tele-
phone number.
Each time you touch
“”, an inputted num-
ber is deleted.
Touch
“” or push of the telephone but-
ton. (ii) By phone book
You can call by phone book data which is
transferred from your cellular phone.
The system has two phone books. You
can register up to 500 numbers in each
book.
This cannot be operated while you are driv-
ing.
Touch the desired key to input the tele-
phone number.
1. Touch the
“Phone Book” switch to
display “Phone Book” screen.
2. Select the desired number from the list.
Touch “” or push of the telephone but-
ton.

11 8
(iii) By dialed numbers
You can call by dialed number. The sys-
tem memorize up to 5 dialed numbers. If it
is over than 5, the oldest number is de-
leted.
This cannot be operated while you are driv-
ing.
1. Touch the “Log” switch to display
“Outgoing Calls” screen.
When you call by phone book, the name
(if registered) is displayed.
When you call the same number continu-
ously, the newest number is only regis-
tered.
2. Select the desired number from the list.
Touch “” or push of the telephone
button. (iv) By received calls
You can call by received calls. When a call
is received, the system memorize up to 5
numbers. If it is over than 5, the oldest
number is deleted.
This cannot be operated while you are driv-
ing.
1. Touch the “Log” switch to display.

11 9
2. Touch
the
“Incoming Calls” switch
to display “Incoming Calls” screen.
When a telephone number registered in
phone book is received, the name and the
number is displayed.
Received calls which you did not answer
are also memorized in the system and
“Abs.” is displayed on the left side of the
number.
Unnotified telephone number such as a
public telephone is not memorized in the
system. 3. Select
the desired number from the list.
Touch “” or push of the telephone
button.
A international phone call may not be
made depending on the cellular phone
which you have. (v) By one touch call
You can call by registered telephone num-
ber which you selected from a phone
book, dialed numbers and received calls.
(See page 123 for registering the one
touch dial.)
1. Touch the “1touch Dial” switch to
display “1touch Dial” screen.

120
2. Touch the desired number to call. You
can change the page by touching
“1touch Dial 2” or “1touch Dial
3”
.
When you push the telephone button while
you are driving, the screen above appears.
Touch the desired name to call. (The tele-
phone number is not displayed.)
(vi) By POI call
You can call by operating a switch when
“Call” is displayed on the screen from
Navigation system. (See page 38 for de-
tails.)
(e) Receive on the Bluetooth
phone
When a call is received, this screen is dis-
played with a sound. T ouch
“” or push
of the telephone button to talk on the
phone.
To hang up the phone:
Touch
“” or push of the
telephone button again.
To refuse to receive the call: Touch
“” and hold it.
To adjust the volume of received call: Touch
“–” or “+”.
On the international phone call, the party’s
name may not be displayed correctly depend-
ing on the cellular phone which you have.
(f) Talk on the Bluetooth phone
While you are talking on the phone, this
screen is displayed. You can do the opera-
tion below on the screen.
To adjust the volume of the party’s voice: Touch
“–” or “+” switch.
To hang up the phone: Touch the
“” switch or push of
the telephone button.
To mute your voice: Touch the
“Mute ON” switch.
To input the Key: Touch the
“09” switch.

121
Touch the desired number to input the key.
To hang up the phone:Touch
“” or push of the telephone
button.
This cannot be operated while you are driv-
ing.
If the continuous tone signal is registered
in a phone book, this screen appears. (If
not registered, “Send” and “Exit” is not
displayed.)
Confirm the number displayed on the
screen and touch
“Send”. The number to
marked sign will be sent.
When you touch
“Exit”, this function will be
finished and normal tone screen appears.
To hang up the phone:
Touch
“” or push of the
telephone button.
The continuous tone signal is the marked sign
(p or w) and the number following tel ephone
number. (ex. 056133p0123w#1
) When you call the number registered in
phone
book and input a code number and the
like to operate an answering machine or use
a telephone service in bank, you can do this
operation.

122
(g) Change the settings of the
Bluetooth phone
Touch the “Settings” switch to display
“Settings” screen.
You can change the settings of the phone.(i) Change the phone book
The system has two phone books. You
can select either of a phone book.
Touch
the “Phone Book 1” or “Phone
Book 2”
switch. (ii) Transfer the telephone number
You can transfer the telephone numbers in
your Bluetooth phone to the system. Up to
500 numbers can be registered in one
phone book.
Transfer it while the engine is running.
1. Touch the “Start Transfer” switch
to display “Data Transfer” screen.

126
Delete the one touch dial
Touch the “Delete” switch of “1touch
Dial”.
Select the desired number from the list.
If you want to delete all the one touch dial
numbers, touch the
“Delete All” switch.
Touch “YES” switch.
Touch
“NO” switch and the previous screen
appears.
Speech command system
The speech command system allows you
to operate the navigation system without
your hands off the steering wheel.
UNL301
1. Push the speech command switch.
A beep sounds and on screen message is
displayed with an indicator at the top left.

127
2. Give a command while an indicator is
shown in the display. If you want to check
the command list, touch the
“Help”
switch to display the Help screen. (See
“Help screen” on page 128.) When you
touch the
“Cancel”, the previous screen
returns.
If the navigation system does not respond or
the confirmation screen does not disappear,
please push the speech command switch
and try again.
If no command is given, a beep sounds and
the indicator disappears 6 seconds later.
If the system does not recognize your
speech, the system will respond with this
message (“System does not recognize this
command, please rephrase your com-
mand.”). Start the operation from the begin-
ning.
UNL303
 Microphone
It is unnecessary to speak directly into the
microphone when giving a command. Speech
command example: Searching for
a route to your home.
1. Push the speech command switch.
2. Say “Home” .
If your home is not registered, you will hear
“Home is not registered”.
3. If the system recognized the command,
the recognition result “Home” is dis-
played on the top of the screen with the
screen message. (Displayed message
and the switches on the screen depend on
the situation.)
Touch or say “Cancel”, and the system will be
canceled. Touch or say “Help”, and displays
the “Help” screen.