key TOYOTA LAND CRUISER 2007 J200 Navigation Manual

cxix
To display the memos listed in a desired
period, touch the
“Period” switch.
Touch the number keys.
After setting the period, touch the
“OK”switch. The “Memo list” screen will be
displayed.
You can set a period from January 1, 2003,
through December 31, 2022, for searching.
To delete and/or edit the memo, touch the
desired memo switch.
To delete all memos, touch the
“Delete
All”
switch. A message appears on the
display. To delete, touch the “Yes”
switch. To cancel the deletion, touch the“No” switch.
To edit: Touch the corresponding
“Memo” or “Location” switch. (See
page cxvii for details.)
To delete: Touch the
“Delete” switch.
(See page cxvii for details.)

cxxiv
(a) Enter the Bluetooth phone
To use a handsfree system, you need to
enter your phone in the system. Once
you registered it, you can make a hands
free call.
1. Push the
“INFO” button to display
the “Information Menu” screen.
5u004
2. Touch the “Telephone” switch to
display “Telephone” screen.
You can also push
of the telephone but-
ton to display this screen when the vehicle is
stopped.
3. Touch the “Settings” switch to dis-
play “Settings” screen.
4. Touch the “Add Phone” switch to
connect your cellular phone to the sys-
tem.
5. When this screen is displayed, input
the Passkey displayed on the screen into
the phone.
For the operation of the phone, see the
manual that comes with your cellular phone.
If you want to cancel it, touch “Cancel”.

cxxvi
Connect the Bluetooth phone
When you turn the ignition key to “ACC”
or “ON”, the selected Bluetooth phone
will be automatically connected and the
connection result is displayed.
Leave the Bluetooth phone enable to con-
nect.
This screen appears when the Bluetooth
phone is first connected after you turn the
ignition key to “ACC” or “ON”.
Reconnect the Bluetooth phone
If the Bluetooth phone is disconnected
with a poor reception from the Blue-
tooth network when the ignition key is
turned to “ACC” or “ON”, the system au-
tomatically reconnects the Bluetooth
phone. In this case, the connection result
is not displayed.
If the Bluetooth is disconnected on purpose
such as you turned your cellular phone OFF,
this does not happen. Reconnect it by the
following methods.
Select the Bluetooth phone again.
Enter the Bluetooth phone.
Confirm the Bluetooth information
You can confirm or change the detail set-
ting of the Bluetooth phone.
Touch the “Settings” of Bluetooth to
display “Bluetooth* Information” screen.
*: Bluetooth is a trademark owned by Blue-
tooth SIG. Inc.

cxxvii
You can change the Device Name and
Passkey.
BD_ADDR is Bluetooth device address.
Do not change the Device Name to the same
name as the one of the other Bluetooth
phones. They cannot be identified.
BD_ADDR is different depending on the
system. You can confirm the address
when it cannot be identified.(i) Change the Device Name
You can change the Device Name to the
desired one from the name already regis-
tered in the system.
Touch the “Change” of Device Name to
display the “Device Name List” screen.
Select the desired name and touch “OK”.(ii) Change the Passkey
The Passkey in the system is initially
fixed. You can change the Passkey with-
in 48 figures.
Touch the “Change” of Passkey to dis-
play “Enter Bluetooth* Passkey” screen.
*: Bluetooth is a trademark owned by Blue-
tooth SIG. Inc.

cxxviii
Touch the desired key to input the Pass-
key.
Each time you touch
“”, an inputted num-
ber is deleted.
Touch
“Enter”.
(c) Delete the Bluetooth phone
1. Touch the “Settings” switch to dis-
play “Settings” screen.
2. Touch the “Delete” switch to dis-
play “Delete Telephone” screen. You can
delete the Bluetooth phone which you
registered.
Select the desired phone from the list and
touch
“OK”.

cxxix
(d) Call on the Bluetooth phone
After you enter the Bluetooth phone,
you can call by using handsfree system.
This system has 6 methods below by
which you call.
(i) By dial
You can call by inputting the telephone
number.
This cannot be operated while you are driv-
ing.
Touch the desired key to input the tele-
phone number.
Each time you touch
“”, an inputted num-
ber is deleted.
Touch
“” or push of the telephone
button.(ii) By phone book
You can call by phone book data which is
transferred from your cellular phone.
The system has two phone books. You
can register up to 500 numbers in each
book.
This cannot be operated while you are driv-
ing.
Touch the desired key to input the tele-
phone number.
1. Touch the
“Phone Book” switch to
display “Phone Book” screen.
2. Select the desired number from the
list.
Touch “” or push of the telephone
button.

cxxxiii
(f) Talk on the Bluetooth phone
While you are talking on the phone, this
screen is displayed. You can do the op-
eration below on the screen.
To adjust the volume of the party’s voice:
Touch
“–” or “+” switch.
To hang up the phone:
Touch the
“” switch or push of
the telephone button.
To mute your voice:
Touch the
“Mute ON” switch.
To input the Key:
Touch the
“09” switch.
Touch the desired number to input the key.
To hang up the phone:
Touch
“” or push of the tele-
phone button.
This cannot be operated while you are driv-
ing.
If the continuous tone signal is registered
in a phone book, this screen appears. (If
not registered, “Send” and “Exit” is not
displayed.)
Confirm the number displayed on the
screen and touch
“Send”. The number
to marked sign will be sent.
When you touch
“Exit”, this function will
be finished and normal tone screen ap-
pears.
To hang up the phone:
Touch
“” or push of the
telephone button.
The continuous tone signal is the marked
sign (p or w) and the number following tele-
phone number. (ex. 056133p0123w#1
)

cxlvii The automatic air conditioning auto-
matically maintains the set tempera-
ture.
This air conditioning features automatic
fan speed and air flow control which auto-
matically selects the most suitable fan
speed and air flow to control the tempera-
ture. The ignition key must be in the “ON”
position.
CLIMATE: Push this button to display
switches for automatic air conditioning con-
trols.
NOTICE
To prevent the battery from being dis-
charged, do not leave the air condi-
tioning on longer than necessary
when the engine is not running.
oxu002
By pushing the switch above, you can
operate the speech command system.
For the operation of the speech command
system and the command, see page cxxxix
and cxli.
(a) Climate control
SETTING OPERATION automatic con-
trol
1. Push the “AUTO” button.
Air flow quantity, switching of the diffusers,
on−off of the air conditioning, and switching
of the air intake between RECIRCULATED
AIR and OUTSIDE AIR are automatically
adjusted. The operation status is shown by
each indicator.
When one of the manual control buttons is
depressed while operating in automatic
mode, the mode relevant to the depressed
button is set. Other conditions continue to
be adjusted automatically.
Push the “OFF” button to turn the air condi-
tioning off.

clvi
Using your audio system:
some basics
This section describes some of the basic
features of the Toyota audio system. Some
information may not pertain to your system.
Your audio system works when the ignition
key is in the “ACC” or “ON” position.
NOTICE
To prevent the battery from being
discharged, do not leave the car
audio on longer than necessary when
the engine is not running.
oxu002
By pushing the above button, you can
operate the speech command system.
For the operation of the speech command
system and the command, see page cxxxix
and cxli.
(a) Turning the system on and off
UNX602
POWERVOL: Push this knob to turn the
audio system on and off. Turn this knob to
adjust the volume. The system turns on in
the last mode used.
AUDIO: Push this button to display switches
for audio system.
VI

clxxviii
The “DVD Hint !” screen appears when
the video screen is first displayed after
you turn the ignition key to “ACC” or
“ON”.
Touch the “OK” switch when you read the
message.(i) Playing a DVD video disc
lxb009a
Push the “AUDIO” button to display this
screen. You can operate the switches
and choose the number of the disc you
want to play. The selected disc is auto-
matically played.
When you touch the “WIDE MODE” switch,
the screen mode can be changed.
When you touch the “PICTURE” switch, the
video screen returns.(ii) Displaying operation switches