fuse TOYOTA LAND CRUISER 2007 J200 Navigation Manual

cxxxii (v) By one touch call
You can call by registered telephone
number which you selected from a phone
book, dialed numbers and received calls.
(See page cxxxvi for registering the one
touch dial.)
1. Touch the “1touch Dial” switch to
display “1touch Dial” screen.
2. Touch the desired number to call. You
can change the page by touching
“1touch Dial 2” or “1touch Dial
3”
.
When you push the telephone button while
you are driving, the screen above appears.
Touch the desired name to call. (The tele-
phone number is not displayed.)
(vi) By POI call
You can call by operating a switch when
“Call” is displayed on the screen from
Navigation system. (See page xlviii for
details.)
(e) Receive on the Bluetooth
phone
When a call is received, this screen is dis-
played with a sound. Touch
“” or
push
of the telephone button to talk
on the phone.
To hang up the phone:
Touch
“” or push of the
telephone button again.
To refuse to receive the call:
Touch
“” and hold it.
To adjust the volume of received call:
Touch
“–” or “+”.
On the international phone call, the party’s
name may not be displayed correctly de-
pending on the cellular phone which you
have.

cxlvii The automatic air conditioning auto-
matically maintains the set tempera-
ture.
This air conditioning features automatic
fan speed and air flow control which auto-
matically selects the most suitable fan
speed and air flow to control the tempera-
ture. The ignition key must be in the “ON”
position.
CLIMATE: Push this button to display
switches for automatic air conditioning con-
trols.
NOTICE
To prevent the battery from being dis-
charged, do not leave the air condi-
tioning on longer than necessary
when the engine is not running.
oxu002
By pushing the switch above, you can
operate the speech command system.
For the operation of the speech command
system and the command, see page cxxxix
and cxli.
(a) Climate control
SETTING OPERATION automatic con-
trol
1. Push the “AUTO” button.
Air flow quantity, switching of the diffusers,
on−off of the air conditioning, and switching
of the air intake between RECIRCULATED
AIR and OUTSIDE AIR are automatically
adjusted. The operation status is shown by
each indicator.
When one of the manual control buttons is
depressed while operating in automatic
mode, the mode relevant to the depressed
button is set. Other conditions continue to
be adjusted automatically.
Push the “OFF” button to turn the air condi-
tioning off.

clxi
(b) Presetting a station
lxb001a
1. Tune in the desired station.
2. Touch one of the station selector
switches (16) and hold it until a beep is
heard. This sets the station to the switch
and the frequency appears on the switch.
Each switch can store FM1, FM2 and AM.
To change the preset station to a different
one, follow the same procedure.
The preset station memory is cancelled
when the power source is interrupted by bat-
tery disconnection or a blown fuse.
(c) Selecting a station
Your Toyota has an electronic tuning radio
(ETR). Tune in the desired station using one
of the following methods.
Preset tuning: Touch the switch (1−6) or
push the “
” or “” side of the “CH” button
for the station you want. The switch (1−6) is
highlighted in green and station frequency
appears on the display.
Manual tuning: Turn the “TUNE” knob brief-
ly. Each time you turn the knob, the radio will
step up or down to another frequency.
Seek tuning: Push the “
” or “” side of
the “SEEK” button and hold it until you hear
a beep. The radio will begin seeking up or
down for a station of the nearest frequency
and will stop on reception. Each time you
push the button, the stations will be
searched out one after another.
lxb001a
Scan tuning:Touch the “SCAN” switch
briefly. “SCAN” appears on the display. The
radio will find the next station up or down the
band, stay there for a few seconds, and then
scan again. To select a station, touch the
“SCAN” switch a second time.
Preset scan tuning: Touch the “SCAN”
switch and hold it until you hear a beep. “P.
SCAN” appears on the display. The radio
will tune in the next preset station up or down
the band, stay there for a few seconds, and
then move to the next preset station. To se-
lect a station, touch the “SCAN” switch a se-
cond time.

clxv
(c) Listening to the satellite radio
lc025
Push the “AM·SAT” button to choose a
SAT channel.
Besides “AM”, “SAT1”, “SAT2” or “SAT3” ap-
pears on the display.
Turn this knob to select the next or pre-
vious channel.
If you turn continuously, you can rapidly
scroll forward or down through the channels.
(d) Presetting a channel
1. Tune in the desired channel.
2. Touch one of the channel selector
switches (16) and hold it until a beep is
heard. This sets the channel to the
switch and the frequency appears on the
switch.
Each switch can store three SAT channels.
To change the preset channel to a different
one, follow the same procedure.
The preset channel memory is cancelled
when the power source is interrupted by bat-
tery disconnection or a blown fuse.