Shift lock TOYOTA LAND CRUISER 2008 J200 Owners Manual

11
P
R
N
+
SDPWR2ND ON/OFF SPEE
D
ITYPC035
ECT switchP. 154
Shift lock override buttonP. 478
Seat heater switchesP. 346
C
Shift leverP. 153
Crawl Control switchP. 197
Cigarette lighterP. 343
Power outletP. 344
AshtrayP. 341
AUX adapterP. 282
Parking brake leverP. 159

35
1−2. Opening, closing and locking the doors
1
Before driving
AlarmSituation Correction procedure
Interior alarm
sounds continu−
ously
*1
When the “ENGINE
START STOP” switch is in
IGNITION ON or ACCES−
SORY mode, an attempt
was made to open the
door and exit the vehicle,
and the shift lever was not
in “P”Shift the shift lever to
“P” and turn the
“ENGINE START
STOP” switch OFF
Interior and exte−
rior alarms sound
continuously
*1
When the “ENGINE
START STOP” switch is in
IGNITION ON or ACCES−
SORY mode, the driver ’s
door was closed after the
key was carried outside
the vehicle, and the shift
lever not in “P”Shift the shift lever to
“P”, turn the “ENGINE
START STOP” switch
OFF and close the
driver ’s door again
Interior alarm
pings once
*1
The electronic key has a
low batteryReplace the electronic
key battery
An attempt was made to
start the engine without the
electronic key being
present, or the electronic
key was not functioning
normallyStart the engine with
the electronic key
present*
2

45
1−2. Opening, closing and locking the doors
1
Before driving
Automatic door locking and unlocking systems
The following functions can be set or canceled:
nSetting and canceling the functions
To switch between setting and canceling, follow the procedure
below:
Close all the doors and switch the “ENGINE START STOP”
switch IGNITION ON mode. (Perform step 2 within 20 sec−
onds.)
Shift the shift lever to “P” or “N”,
press and hold the driver ’s door
lock switch (
or) for 5 sec−
onds then release.
The shift lever and switch posi−
tions corresponding to the
desired function to be set or can−
celed are shown as follows.
Function Operation
Shift position linked
door locking functionShifting the shift lever out of “P” locks all
doors.
Shift position linked
door unlocking functionShifting the shift lever to “P” unlocks all
doors.
Speed linked door lock−
ing functionAll doors are locked when the vehicle speed is
approximately 12 mph (20 km/h) or higher.
Driver ’s door linked door
unlocking function
All doors are unlocked when the driver ’s door
is opened within 10 seconds after turning the
“ENGINE START STOP” switch OFF.
STEP1
STEP 2

46 1−2. Opening, closing and locking the doors
When the setting or canceling operation is complete, all doors are
locked and then unlocked.
FunctionShift leverpositionSwitch position
Shift position linked door lock−
ing function
“P”
Shift position linked door
unlocking function
Speed linked door locking func−
tion
“N”
Driver ’s door linked door unlock−
ing function
nImpact detection door lock release system
In the event that the vehicle is subject to a strong impact, all the doors are
unlocked.
Depending on the force of the impact or the type of accident, however, the
system may not operate.
nUsing the mechanical key
The doors can also be locked and unlocked with the mechanical key.
(P. 481)
nCustomization that can be configured at Toyota dealer
Settings (e.g. unlocking function using a key) can be changed. (Customiz−
able features
P. 519)

62
1−3. Adjustable components (seats, mirrors, steering wheel)
Driving position memor y system
Your preferred driving position (th e position of the driver ’s seat,
steering wheel and outside rear view mirrors) can be entered into the
computer ’s memory and recalled with
the touch of a button. It is also
possible to set this function to activate automatically when the
doors are unlocked.
Three different driving positions can be entered into memory.
nEntering a position to memory
Check that the shift lever is set in “P”.
Switch to IGNITION ON mode.
Adjust the driver ’s seat, steering wheel, and outside rear
view mirrors to the desired positions.
While pressing the “SET” but−
ton, press button “1”, “2” or “3”
until the signal beeps.
If the selected button has
already been preset, the previ−
ously recorded position will be
overwritten.
nRecalling the memorized position
Check that the shift lever is set in “P”.
Switch to IGNITION ON mode.
Press button “1”, “2” or “3” to
recall the desired position.
STEP1
STEP 2
1SET23
1SET23
ITY13C036
STEP3STEP 3
STEP 1
1SET23
1SET23
ITY13C038
STEP2

140
2−1. Driving procedures
Driving the vehicle
Starting on a steep incline
Firmly set the parking brake and shift the shift lever to “D”.
Gently depress the accelerator pedal.
Release the parking brake.
The following procedures should be observed to ensure safe driv
ing.
nStarting the engine ( P. 150)
nDriving
With the brake pedal depressed, shift the shift lever to “D”.
( P. 153)
Release the parking brake. ( P. 159)
Gradually release the brake pedal and gently push the
accelerator pedal to accelerate the vehicle.
nStopping
With the shift lever in “D”, push the brake pedal.
If necessary, set the parking brake.
When the vehicle is stopped for an extended period of time, shift the
shift lever to “P” or “N”.
( P. 153)
nParking the vehicle
With the shift lever in “D”, push the brake pedal.
Set the parking brake. (
P. 159)
Shift the shift lever to “P”. ( P. 153)
Press the “ENGINE START STOP” switch and stop the
engine.
Lock the door, making sure that you have the key on your
person.
STEP1
STEP 2
STEP 3
STEP 1
STEP 2
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 1
STEP 2
STEP 3

145
2−1. Driving procedures
2
When driving
CAUTION
nWhen the vehicle is parked
lDo not leave glasses, cigarette lighters, spray cans, or soft drink cans in
the vehicle when it is in the sun.
Failure to do so may result in the following:
Gas may leak from a cigarette lighter or spray can, and may lead to a
fire.
The temperature inside the vehicle may cause the plastic lenses and
plastic material of eye glasses to deform or crack.
Soft drink cans may fracture, causing the contents to spray over the
interior of the vehicle, and may also cause a short circuit in the vehi−
cle’s electrical components.
lAlways apply the parking brake, shift the shift lever to “P”, stop the engine
and lock the vehicle.
Do not leave the vehicle unattended while the engine is running.
lDo not touch the exhaust pipe while the engine is running or immediately
after turning the engine off.
Doing so may cause burns.
lDo not leave the engine running in an area with snow build up, or where it
is snowing. If snowbanks build up around the vehicle while the engine is
running, exhaust gases may collect and enter the vehicle. This may lead
to death or a serious health hazard.
nExhaust gases
Exhaust gases include harmful carbon monoxide (CO) that is colorless and
odorless. Inhaling exhaust gases may lead to death or a serious health haz−
ard.
lIf the vehicle is in a poorly ventilated area, stop the engine. In a closed
area, such as a garage, exhaust gases may collect and enter the vehicle.
This may lead to death or a serious health hazard.
l
The exhaust system should be checked occasionally. If there is a hole or
crack caused by corrosion, damage to a joint or abnormal exhaust noise,
make sure to have the vehicle inspected and repaired by your Toyota
dealer. Failure to do so may allow exhaust gases to enter the vehicle,
resulting in death or a serious health hazard.

151
2−1. Driving procedures
2
When driving
nWhen the steering lock cannot be released
nIf the engine does not start
The engine immobilizer system may not have been deactivated. (
P. 93)
nWhen the “ENGINE START STOP” switch indicator flashes in amber
The system may be malfunctioning. Have the vehicle inspected by your Toy−
ota dealer immediately.
nAuto power off function
If the vehicle is left in ACCESSORY mode for more than an hour with the
shift lever in “P”, the “ENGINE START STOP” switch will automatically turn
off.
n
P. 3 2
n
P. 481
n
P. 3 0
n
P. 3 3The green indicator light on the “ENGINE
START STOP” switch will flash and a
message will be shown on the multi−infor−
mation display. Press the “ENGINE
START STOP” switch again while turning
the steering wheel left and right.

191
2−4. Using other driving systems
2
When driving
Shifting between “H4”and “L4”
nShifting from “H4” to “L4”
Stop the vehicle completely.
Shift the shift lever to “N”.
Push and turn the four−wheel drive control switch fully clock−
wise.
Maintain this condition until the low speed four−wheel drive indica−
tor light turns on.
nShifting from “L4” to “H4”
Stop the vehicle completely.
Shift the shift lever to “N”.
Turn the four−wheel drive control switch fully counterclock−
wise.
Maintain this condition until the low speed four−wheel drive indica−
tor light turns off.
STEP1
STEP 2
STEP 3
STEP 1
STEP 2
STEP 3

192 2−4. Using other driving systems
Neutral position
Shifting to the neutral position cuts drive power to the wheels.
n
Shifting from “H4” to the neutral position
Stop the vehicle completely.
Make sure the vehicle is stopped in a safe place while carrying out
the following procedure.
Confirm the following:
lThe four wheel−drive control switch is in “H4”. (The low speed four−
wheel drive indicator light is not illuminated.)
If the switch is in “L4”, turn it to “H4”. (
P. 190)
lThe center differential is unlocked. (The center differential lock indi−
cator light is not illuminated.)
If the center differential is locked,
press the center differential lock/
unlock switch to unlock the center differential. ( P. 190)
Set the parking brake firmly and put the shift lever in “N”.
Turn the engine off if the engine is running, then turn the
“ENGINE START STOP” switch to the IGNITION ON mode.
Do not start the engine till the end of the procedure.
Shift the shift lever to “P”.
Depress and release the brake pedal 3 times.
Depress the pedal firmly each time, then keep the pedal depressed
the third time.
Shift the shift lever to “N”.
Depress and release the brake pedal 3 times.
Release the brake pedal once and then depress and release the
brake pedal 3 times.
Depress the pedal firmly each time, then keep the pedal depressed
the third time.
STEP1
STEP 2
STEP 3
STEP 4
STEP 5
STEP6
STEP 7
STEP 8