sensor TOYOTA MIRAI 2016 1.G Quick Reference Guide

10 The Automatic High Beam uses an in-vehicle camera sensor to assess the
brightness of streetlights, the lights of oncoming and preceding vehicles, etc., and
automatically turns high beams on or off as necessary.
To turn the high beams on/off manually, pull the lever to the original position or
press the switch.
Refer to the Owner‘s Manual for more details on this system before attempting
to use it.
Automatic high beams
1) Activate the system2) Press the Automatic High Beam
switch When the fuel cell system is stopped, water is automatically purged from the
tailpipe. To minimize water accumulation in parking garages, etc., purge can be
done manually before parking. While the “READY” indicator is on, press the H2O
switch.
Refer to the Owner‘s Manual for more details on this system before attempting
to use it.
Water release (H2O) switch
HYDROGEN FUEL CELL SYSTEM
& SAFETY FEATURES

11
OVERVIEWHYDROGEN FUEL CELL SYSTEM
& SAFETY FEATURESFEATURES/OPERATIONS
SAFETY AND EMERGENCY FEATURES
While driving on a road that has lane markers, this system recognizes the lane
markers using a camera sensor and alerts the driver when the vehicle deviates
from its lane.
Refer to the Owner‘s Manual for more details on this system before attempting
to use it.
Press the LDA switch (in steering wheel) to turn the LDA system ON, the indicator
will illuminate. Press again to turn OFF.
When the inside of both lane lines turn white:
- Indicates that both right and left lane markers are recognized.
When the inside of either lane line turns white:
- Indicates that the lane marker on the white-marked side is recognized.
When the inside of both lane lines are black:
- Indicates that no lane markers are recognized or the LDA system is temporarily
canceled.
Lane Departure Alert (LDA)
Turning the LDA system ON
Indication on the multi-information display
Camera sensor
Press to ON
Multi-information display

12
HYDROGEN FUEL CELL SYSTEM
& SAFETY FEATURES

Pre-Collision System (PCS)
When a high possibility of a frontal collision is detected by the radar sensor, a
buzzer sounds and a message urging the driver to take evasive action appears
on the multi-information display. If the driver then applies brakes, the system
applies greater brake force in relation to how strongly the brake pedal is
depressed. If the system determines that a collision is unavoidable, the brakes
are automatically applied to reduce the collision speed. The alert timing for the
pre-collision system can be changed or turned on/off, as necessary, by pressing
TRAC switch.
The system is enabled each time the power switch is turned to ON mode.
Refer to the Owner‘s Manual for more details on this system before attempting
to use it.


Each time the Pre-Collision System switch is pressed, the response to the distance
changes as follows:
Far
Middle
Near
Press the TRAC switch for 3 seconds or more.
Changing the pre-collision warning timing
Disabling the Pre-Collision System

18
FEATURES/OPERATIONS
Windshield wipers & washer
MIST Temporary operation
AUTO Rain-sensing operation
LO Low speed operation
HI High speed operation
OFF
Pull to wash and wipe
Select AUTO to increase or
decrease sensor sensitivity.
Operating wiper lever
* When AUTO is selected, wipers will
operate automatically when sensor
detects falling rain.
Increase
Decrease
Push lever to move steering wheel:
- up, down to adjust angle,
- left, right to adjust length (toward driver and away from driver.)
NOTE: Do not attempt to adjust while the vehicle is in motion.
Tilt & telescopic steering wheel
Length
Angle

29
OVERVIEW
HYDROGEN FUEL CELL VEHICLE SYSTEMFEATURES/OPERATIONS
SAFETY AND EMERGENCY FEATURES
(QKDQFHG9HKLFOH6WDELOLW\&RQWUROSURYLGHVFRRSHUDWLYHFRQWURORIWKH$%675$&
VSC and EPS.
Enhanced VSC helps to maintain directional stability when loss of traction occurs
during a turn.
(QKDQFHG9HKLFOH6WDELOLW\&RQWURO96&
VSC helps prevent loss of traction during cornering by reducing Motor power
RXWSXWDQG7UDFWLRQ&RQWUROKHOSVPDLQWDLQWUDFWLRQRQORRVHJUDYHODQGZHWLF\
or uneven surfaces by applying brake force to the spinning wheel(s).
Toyota’s TRAC sensors are activated when one of the drive wheels starts to slip.
TRAC limits Motor power output and applies the brakes to the spinning wheel. This
transfers power to the wheels that still have traction to help keep you on track.
7UDFWLRQ&RQWURO75$&
$QWL/RFN%UDNH6\VWHP$%6
ABS helps prevent brakes from locking up by “pulsing” brake pressure to each
wheel. This limits brake lockup and helps provide directional control for the
current road conditions.
Toyota’s ABS sensors detect which wheels are locking up and limits wheel lockup
by “pulsing” each wheel’s brakes independently. Pulsing releases brake pressure
repeatedly for fractions of a second. This helps the tires attain the traction that
FXUUHQWURDGFRQGLWLRQVZLOODOORZKHOSLQJ\RXWRVWD\LQGLUHFWLRQDOFRQWURO
(OHFWURQLF%UDNH)RUFH'LVWULEXWLRQ(%'
7R\RWD