phone TOYOTA PRIUS 2004 2.G Navigation Manual

11 6 (iii) By dialed numbers
You can call by dialed number. The sys-
tem memorize up to 5 dialed numbers. If it
is over than 5, the oldest number is de-
leted.
This cannot be operated while you are driv-
ing.
1. Touch the “Log” switch to display
“Dialed no.” screen.
When you call by phonebook, the name (if
registered) is displayed.
When you call the same number continu-
ously, the newest number is only regis-
tered.
2. Select the desired number from the list.
Touch “” or push of the telephone
button.(iv) By received calls
You can call by received calls. When a call
is received, the system memorize up to 5
numbers. If it is over than 5, the oldest
number is deleted.
This cannot be operated while you are driv-
ing.
1. Touch the “Log” switch to display.

11 7 2. Touch the
“Received Calls” switch
to display “Rec. Calls” screen.
When a telephone number registered in
phonebook is received, the name and the
number is displayed.
Received calls which you did not answer
are also memorized in the system and
“Abs.” is displayed on the left side of the
number.
Un notified telephone number such as a
public telephone is not memorized in the
system.3. Select the desired number from the list.
Touch “” or push of the telephone
button.
A international phone call may not be made
depending on the cellular phone which you
have.(v) By one touch call
You can call by registered telephone num-
ber which you selected from a phonebook,
dialed numbers and received calls. (See
page 121 for registering the one touch
dial.)
This cannot be operated while you are driv-
ing.
1. Touch the “One Touch Dial” switch
to display “One Touch Dial” screen.

11 8
2. Touch the desired number to call. You
can change the page by touching
“One
Touch Dial 2” or “One Touch Dial
3”
.
When you push the telephone button while
you are driving, the screen above appears.
Touch the desired name to call. (The tele-
phone number is not displayed.)(vi) By POI call
You can call by operating a switch when
“Call” displayed on the screen from Navi-
gation system. (See page 38 for details.)
(e) Receive the Bluetooth phone
When a call is received, this screen is dis-
played with a sound. Touch
“” or push
of the telephone button to talk on the
phone.
To hang up the phone:
Touch
“” or push of the
telephone button again.
To refuse to receive the call:
Touch
“” and hold it.
To adjust the volume of received call:
Touch
“–” or “+”.
On the international phone call, the name of
the remote party may not be displayed cor-
rectly depending on the cellular phone which
you have.

11 9
(f) Talk on the Bluetooth phone
While you are talking on the phone, this
screen is displayed. You can do the opera-
tion below on the screen.
To adjust the volume of the receiving voice on
the phone:
Touch
“–” or “+” switch.
To hang up the phone:
Touch the
“” switch or push of
the telephone button.
To mute your voice:
Touch the
“Mute ON” switch.
To input the Key:
Touch the
“09” switch.
Touch the desired number to input the key.
To hang up the phone:
Touch
“” or push of the telephone
button.
This cannot be operated while you are driv-
ing.
If the continuous tone signal is registered
in a phonebook, this screen appears. (If
not registered, “Send” and “Exit” is not
displayed.)
Confirm the number displayed on the screen
and touch
“Send”. The number to marked
sign will be sent.
When you touch
“Exit”, this function will be
finished and normal tone screen appears.
To hang up the phone:
Touch
“” or push of the
telephone button.
The continuous tone signal is the marked sign
(p or w) and the number following telephone
number. (ex. 056133p0123w#1
)

120 When you call the number registered in
phonebook and input a code number and the
like to operate a answering machine or use a
telephone service in bank, you can do this op-
eration.
(g) Change the settings of the
Bluetooth phone
Touch the “Settings” switch to display
“Settings” screen and scroll with “”.
You can change the settings of the phone.(i) Change the phonebook
The system has two phonebooks. You can
select either of a phonebook.
Touch the “Phone Book 1” or “Phone
Book 2”
switch.

121 (ii) Transfer the telephone number
You can transfer the telephone numbers in
your Bluetooth phone to the system. Up to
500 numbers can be registered in one
phonebook.
Transfer it while the engine is running.
1. Touch the “Start Transfer” switch
to display “Data Transfer” screen.
2. Touch the “Overwrite” or “Add”
switch if the phonebook is not empty.
3. Transfer the phonebook data to the
system with operating the Bluetooth
phone.
This screen appears while transferring. To
cancel it, touch the
“Cancel” switch. If the
transferring is interrupted on the way, the
phonebook data transferred by then can be
memorized in the system.(iii) Register the one touch dial
You can register the desired telephone
number from phonebooks, dialed num-
bers and received calls. Up to 17 items the
one touch dial can be registered.1. Touch the “Set One Touch” switch
in which you want to register the phone
number.

122
2. Touch the desired telephone number.
Select the new registration from 118 ex-
cept 6 and touch the switch.
A latest received number is registered in the
6th item.(iv) Delete the memory
Delete the telephone number in the
phonebook.
Touch the “Delete” switch of “Phone
Book”.
Select the desired number from the list.If you want to delete all the phone numbers in
phonebook, touch the
“Delete All” switch.
Touch “YES” switch.
Touch
“NO” switch and the previous screen
appears.

125
Speech command system
The speech command system allows you
to operate the navigation system without
your hands off the steering wheel.
UNL301
1. Push the speech command switch.
A beep sounds and on screen message is
displayed with an indicator at the top left.
2. Give a command while an indicator is
shown in the display. If you want to check
the command list, touch the
“Help”
switch to display the Help screen. (See
“Help screen” on page 126.) When you
touch the
“Cancel”, the previous screen
returns.
If the navigation system does not respond or
the confirmation screen does not disappear,
please push the speech command switch
and try again.
If no command is given, a beep sounds and
the indicator disappears 6 seconds later.
If the system does not recognize your
speech, the system will respond with this
message (“System does not recognize this
command, please rephrase your com-
mand.”). Start the operation from the begin-
ning.
UNL303
Microphone
It is unnecessary to speak directly into the
microphone when giving a command.