ignition TOYOTA PRIUS 2005 2.G Owners Manual

103
When the headlight switch is turned to the
first or second clickstop, the brightness of
the instrument cluster will be reduced
slightly unless the instrument panel light
control dial is turned fully on.
NOTICE
To prevent the battery from being dis-
charged, do not leave the switch on
longer than necessary when the hy-
brid system is not running.
Daytime running light system*
The headlights turn on at reduced intensi-
ty when the parking brake is released with
the hybrid system started, even with the
light switch in the “OFF” position.
To turn on the other exterior lights and
instrument panel lights, twist the knob to
the position 1.
To turn off the daytime running light sys-
tem, twist the knob to the position 2 or
position 3 with the headlights on or turn
the ignition switch off.
*: Equipped on vehicles sold in Canada
23p109
HighLow beams—For high beams, turn
the headlights on and push the lever away
from you (position 1). Pull the lever to-
ward you (position 2) for low beams.
The headlight high beam indicator light
(blue light) on the instrument panel will
tell you that the high beams are on.
Flashing the high beam headlights
(position 3)—Pull the lever all the way
back. The high beam headlights turn off
when you release the lever.
You can flash the high beam headlights
even with the knob turned to “OFF”.
23p110
TURN SIGNALS
To signal a turn, push the headlight/
turn signal lever up or down to position
1.
The hybrid system must be in the “IG −
ON” mode.
The lever automatically returns after you
make a turn, but you may have to return
it by hand after you change lanes.
To signal a lane change, move the lever
up or down to the pressure point (position
2) and hold it.

141
The slip indicator light comes on when the
“IG−ON” mode is enabled and will go off
after the “READY” light comes on. If the
indicator light does not come on when the
ignition is turned on, contact your Toyota
dealer.
25p117
“VSC” warning light
This light warns that there is a problem
somewhere in the vehicle stability control
system.
The light will come on when the “IG −ON”
mode is enabled and will go off after the
“READY” light comes on.
If the light comes on while driving, the
system does not work. However, because
the conventional braking still operates, you
can drive your vehicle without damaging
it. Contact your Toyota dealer. In the following cases, contact your Toyota
dealer:
The warning light does not come on
after the “IG
−ON” mode is enabled.
The warning light remains on after the
“READY” light comes on.
The warning light comes on while driv-
ing.

207
30p001d
The threeway catalytic converters are
emission control devices installed in
the exhaust system.
Its purpose is to reduce pollutants in the
exhaust gas.
CAUTION
Keep people and combustible mate-
rials away from the exhaust pipe
while the engine is running. The
exhaust gas is very hot.
Do not drive, idle or park your ve-
hicle over anything that might burn
easily such as grass, leaves, paper
or rags.
NOTICE
A large amount of unburned gases
flowing into the threeway catalytic
converter may cause it to overheat
and create a fire hazard. To prevent
this and other damage, observe the
following precautions:
Use only unleaded gasoline.
 Do not drive with an extremely low
fuel level; running out of fuel could
cause the engine to misfire, creat-
ing an excessive load on the three
way catalytic converter.
 Do not turn off the ignition while
the vehicle is moving.
 Keep your engine in good running
order. Malfunctions in the engine
electrical system, electronic ignition
system/distributor ignition system
or fuel system could cause an ex-
tremely high temperature.
 If the engine becomes difficult to
start or stalls frequently, take your
vehicle in for a checkup as soon
as possible. Remember, your Toyota
dealer knows your vehicle and its
threeway catalytic converter sys-
tem best.
To ensure that the threeway cata-
lytic converter and the entire emis-
sion control system operate proper-
ly, your vehicle must receive the
periodic inspections required by the
Toyota Maintenance Schedule. For
scheduled maintenance information,
refer to the “Scheduled Maintenance
Guide” or “Owner ’s Manual Supple-
ment”.
Threeway catalytic converters

280
If you perform maintenance by yourself,
be sure to follow the correct procedure
given in this Section.
You should be aware that improper or in-
complete servicing may result in operating
problems.
Performing do−it−yourself maintenance
during the warranty period may affect your
warranty coverage. Read the separate
Toyota Warranty statement for details and
suggestions.
This Section gives instructions only for
those items that are relatively easy for an
owner to perform. As explained in Section
7, there are still a number of items that
must be done by a qualified technician
with special tools.
For information on tools and parts for do −
it −yourself maintenance, see “Parts and
tools” on page 283.
Utmost care should be taken when work-
ing on your vehicle to prevent accidental
injury. Here are a few precautions that
you should be especially careful to ob-
serve:CAUTION
When the hybrid system is on, keep
hands, clothing, and tools away
from the moving fan and engine
drive belts. (Removing rings,
watches, and ties is advisable.)
Right after driving, the engine
compartment—the engine, radiator,
exhaust manifold and spark plug
boots, etc.—will be hot. So be care-
ful not to touch them. Oil, fluids
and spark plugs may also be hot.
If the hybrid system is hot, do not
remove the radiator cap or loosen
the drain plugs to prevent burning
yourself.
Do not leave anything that may
burn easily, such as paper or rags,
in the engine compartment.
Do not smoke, cause sparks or al-
low open flames around fuel or the
batteries. Their fumes are flam-
mable.
When the hybrid system is operat-
ing with the “READY” light on, the
engine is automatically started in
some case. When you inspect the
engine compartment, be sure to
press the “POWER” switch to the
“OFF” mode.
Do not get under your vehicle with
just the body jack supporting it. Al-
ways use automotive jack stands or
other solid supports.
Be sure that the hybrid system is
in the “OFF” mode if you work near
the electric cooling fans or radiator
grille. With the ignition on, the
electric cooling fans will automati-
cally start to run if the engine cool-
ant temperature is high and/or the
air conditioning is on.
Use eye protection whenever you
work on or under your vehicle
where you may be exposed to fly-
ing or falling material, fluid spray,
etc.
Be extremely cautious when work-
ing on the batteries. It contains poi-
sonous and corrosive sulfuric acid
or strong alkali.
Doityourself service
precautions

317
22. IGN 7.5 A: Hybrid system, hybrid ve-
hicle immobilizer system, SRS air bags
23. SPARE 30 A: Spare
24. SPARE 15 A: Spare
25. DRL 7.5 A: Daytime running light sys-
tem
26. HLP LO RH 15 A (Vehicles with dis- charged headlight) or 10 A (Vehicles
with halogen headlight): Right−hand
headlight (low beam)
27. HLP LO LH 15 A (Vehicles with dis- charged headlight) or 10 A (Vehicles
with halogen headlight): Left−hand
headlight (low beam)
28. HLP HI RH 10 A: Right−hand head-
light (high beam)
29. HLP HI LH 10 A: Left−hand headlight
(high beam)
30. EFI 15 A: Multiport fuel injection sys-
tem/sequential multiport fuel injection
system
31. AM2 15 A: “IGN” fuse, ignition system
32. HORN 10 A: Horn
33. HEV 20 A: Hybrid system
34. P CON MAIN 7.5 A: Parking control
system, hybrid vehicle immobilizer sys-
tem 35. ABS1 25 A:
Anti−lock brake system
36. ETCS 10 A: Electronic throttle control
system
37. BATT FAN 10 A: Battery cooling fan
38. HAZ 10 A: Turn signal lights, emergen-
cy flasher
39. DOME 15 A: Audio system, interior
lights, smart entry and start system,
gauge and meter, turn signal lights,
luggage room light, clock
40. ABS MAIN3 15 A: Anti−lock brake sys-
tem
41. ABS MAIN2 10 A: Anti−lock brake sys-
tem
42. ABS MAIN1 10 A: Anti−lock brake sys-
tem
43. FR FOG 15 A: Fog lights
44. CHS W/P 10 A: CHS W/P
45. AMP 30 A: Audio system
46. PTC HTR2 30 A: PTC heater
47. PTC HTR1 30 A: PTC heater
48. CDS FAN 30 A: Electric cooling fan
49. DC/DSS 5 A: Inverter and converter
50. MAIN 120 A: Hybrid system

330
Spark ignition system ofyour Toyota
The spark ignition system in your
Toyota meets all requirements of
the Canadian Interference −Causing
Equipment Standard.
Installation of a mobile twoway radio system
As the installation of a mobile
two −way radio system in your ve-
hicle could affect electronic sys-
tems such as multiport fuel injec-
tion system / sequential multiport
fuel injection system, cruise con-
trol system, anti −lock brake sys-
tem, vehicle stability control sys-
tem, SRS airbag system, seat belt
pretensioner system and Toyota
hybrid system, be sure to check
with your Toyota dealer for pre-
cautionary measures or special
instructions regarding installation.
Tires and loading on your Toyota
Underinflated or overinflated
tire inflation pr essure and the
excess load may result in the
deterioration of steering ability
and braking ability, leading to
an accident. Check the tire
inflation pressure periodically
and be sure to keep the load
limits given in this Owner ’s
Manual. For details about tire
inflation pressure and load lim-
its, see page 291 and pages
228.