cable TOYOTA RAV4 1996 Service Repair Manual

AX0T5−01
Q06565
Q07898
Q07907
Neutral Basic
Line
Groove
Q07906
AX−4
− AUTOMATIC TRANSAXLE (A241E)PARK/NEUTRAL POSITION (PNP) SWITCH
1996 RAV4 (RM447U)
PARK/NEUTRAL POSITION (PNP)
SWITCH
ON−VEHICLE REPAIR
1. REMOVE NO.2 ENGINE UNDER COVER
2. DISCONNECT PARK/NEUTRAL POSITION SWITCH
CONNECTOR
3. REMOVE PARK/NEUTRAL POSITION SWITCH
(a) Remove the nut and disconnect the shift control cable.
(b) Remove the nut and shift control lever.
(c) Using a screwdriver, pry off the lock plate.
(d) Remove the nut and lock plate.
(e) Remove the 2 bolts and pull out the park/neutral position
switch.
4. INSTALL PARK/NEUTRAL POSITION SWITCH
(a) Temporarily install the park/neutral position switch with
the 2 bolts.
(b) Install a new lock plate and tighten the nut.
Torque: 6.9 N·m (70 kgf·cm, 61 in.·lbf)
(c) Stake the nut with the lock plate.
(d) Adjust the park/neutral position switch (See page
DI−127).
HINT:
Align the groove and park/neutral basic line.
(e) Tighten the 2 bolts.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
(f) Install the shift control lever with the nut.
(g) Connect the control cable with the nut.
Torque: 13 N·m (135 kgf·cm, 10 ft·lbf)
5. CONNECT PARK/NEUTRAL POSITION SWITCH CON-
NECTOR
6. INSTALL NO.2 ENGINE UNDER COVER

AT8584
AT8586
Z11664
B A
B
B A
B A
A A CA
AT3327
Q06411
BA AX−6
− AUTOMATIC TRANSAXLE (A241E)VALVE BODY ASSEMBLY
1996 RAV4 (RM447U)
6. REMOVE MANUAL DETENT SPRING
Remove the bolt and manual detent spring.
7. REMOVE 3 SOLENOID CONNECTORS
8. REMOVE VALVE BODY
(a) Disconnect the throttle cable.
(b) Remove the 11 bolts and wire retainer.
Bolt length:
Bolt A: 20 mm (0.79 in.)
Bolt B: 30 mm (1.18 in.)
Bolt C: 55 mm (2.17 in.)
(c) Disconnect the manual valve connecting rod.
(d) Remove the valve body.
9. REMOVE 3 SOLENOID VALVES
(a) Remove the 3 solenoid valves.
(b) Remove the O−rings from each of the solenoid valves.
10. INSTALL SHIFT SOLENOID VALVE
(a) Coat new O−rings with ATF and install them to the each
of the solenoid valve.
(b) Install the 3 shift solenoid valves with the 2 bolts.
Torque:
Bolt A: 6.4 N·m (65 kgf·cm, 56 in.·lbf)
Bolt B: 10 N·m (100 kgf·cm, 7 ft·lbf)

AT3327
Z11664
B A
B
B A
B A
A A C
AT8586
AT8584
Q06418
− AUTOMATIC TRANSAXLE (A241E)VALVE BODY ASSEMBLY
AX−7
1996 RAV4 (RM447U)
11. INSTALL VALVE BODY
(a) Install the valve body.
(b) Connect the manual valve connecting rod.
(c) Install the 17 bolts and wire retainer.
Bolt length:
Bolt A: 20 mm (0.79 in.)
Bolt B: 30 mm (1.18 in.)
Bolt C: 55 mm (2.17 in.)
Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
(d) Connect the throttle cable.
12. CONNECT 3 SOLENOID CONNECTORS
13. INSTALL MANUAL DETENT SPRING
Install the manual detent spring with the bolt.
Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
HINT:
Check that the manual valve lever is in contact with the center
of the roller at the tip of the detent spring.
14. INSTALL OIL PIPE CLAMP AND OIL PIPES
(a) Install the 5 pipes with a large screwdriver.
(b) Install the oil pump clamp with the bolt.
Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)

Q06117
AX055−02
AT5641
Q057310.8−1.5 mm (0.031−0.059 in.) 200 mm (7.87 in.)
− AUTOMATIC TRANSAXLE (A241E)THROTTLE CABLE
AX−9
1996 RAV4 (RM447U)
THROTTLE CABLE
ON−VEHICLE REPAIR
1. DISCONNECT THROTTLE CABLE FROM ENGINE
2. REMOVE NO.2 ENGINE UNDER COVER
3. REMOVE PARK/NEUTRAL POSITION SWITCH (See
page AX−4)
4. REMOVE VALVE BODY (See page AX−5)
5. REMOVE THROTTLE CABLE
(a) Remove the retaining bolt and plate.
(b) Pull out the cable from the transaxle case.
6. INSTALL THROTTLE CABLE
If throttle cable is new, do the following operations (a) − (c).
(a) Bend the cable so there is a radius of about 200 mm (7.87
in.).
(b) Pull theinner cable lightly until a slight resistance is felt,
and hold it.
(c) Stake the stopper 0.8 − 1.5 mm (0.031 − 0.059 in.) from
the end of outer cable.
(d) Be sure to push it in all the way.
(e) Install the bolt.
7. INSTALL VALVE BODY (See page AX−5)
8. INSTALL PARK/NEUTRAL POSITION SWITCH (See
page AX−4)
9. INSTALL NO.2 ENGINE UNDER COVER
10. CONNECT THROTTLE CABLE
11. ADJUST THROTTLE CABLE (See page DI−127)
12. FILL ATF AND CHECK ATF (See page DI−127)

AX0T8−01
Z18886
RH Drive Shaft
LH Drive Shaft  Snap Ring
64 (650, 47)
 Cotter Pin
Lock Cap
216 (2,200, 159)
 Gasket
49 (500, 36)
7.0 (75, 65 in.·lbf)
62 (630, 46)
48 (490, 35)
Front Exhaust PipeEngine Mounting
Center MemberPS Gear Assembly
Front Suspension Crossmember
Assembly with Stabilizer Bar
RH Engine Under Cover
LH Engine Under Cover
137 (1,400, 101)
206 (2,100, 152)
127 (1,300, 94)
72 (730, 53)

73 (740, 54)
N·m (kgf·cm, ft·lbf)
: Specified torque
 Non−reusable part
113 (1,150 83)
 Cotter Pin
 Gasket
35 (360, 26)
64 (650, 47)
64 (650, 47)
19 (194, 14)
25 (250, 18)
46 (470, 34)
27 (280, 20)
25 (250, 18)
9.0 (95, 78 in.·lbf)
64 (650, 47)
9.0 (95, 78 in.·lbf)
37 (380, 27)
13 (135, 10)
39 (400, 29)64 (650, 47)
 GasketStarterEngine Wire
Clamp Plug for Line
Pressure Test
Shift Control
Cable ClipRear End Plate Stiffener Platex 6 Torque Converter
ClutchEngine Coolant Reservoir TankABS RelayAir Intake Connector
Air Cleaner
Case Assembly AX−14
− AUTOMATIC TRANSAXLE (A241E)AUTOMATIC TRANSAXLE UNIT
1996 RAV4 (RM447U)
AUTOMATIC TRANSAXLE UNIT
COMPONENTS

D02186
AX127−01
Q08747
Q08761
D02187
Q08763
− AUTOMATIC TRANSAXLE (A241E)AUTOMATIC TRANSAXLE UNIT
AX−15
1996 RAV4 (RM447U)
REMOVAL
1. DISCONNECT THROTTLE CABLE
2. REMOVE ENGINE COOLANT RESERVOIR TANK
3. REMOVE AIR CLEANER ASSEMBLY
(a) Disconnect the connector and ABS relay.
(b) Remove the 3 bolts and air cleaner assembly.
4. REMOVE GROUND CABLE
Remove the bolt from the transaxle.
Torque: 19 N·m (194 kgf·cm, 14 ft·lbf)
5. REMOVE SET NUT OF ENGINE WIRE CLAMP
6. REMOVE STARTER
(a) Disconnect the connector and nut from the starter.
(b) Remove the 2 bolts and disconnect the engine wire.
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
(c) Remove the starter.
7. REMOVE 3 UPPER SIDE TRANSAXLE MOUNTING
BOLTS
Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)
8. INSTALL ENGINE SUPPORT FIXTURE

Q08764
Q08765
Q08766
Q08767
AX−16
− AUTOMATIC TRANSAXLE (A241E)AUTOMATIC TRANSAXLE UNIT
1996 RAV4 (RM447U)
9. REMOVE ENGINE LEFT MOUNTING BOLT AND NUTS
Torque:
Bolt: 64 N·m (650 kgf·cm, 47 ft·lbf)
Nut: 64 N·m (650 kgf·cm, 47 ft·lbf)
10. REMOVE LEFT AND RIGHT ENGINE UNDER COVERS
11. DRAIN ATF
12. REMOVE LEFT AND RIGHT DRIVE SHAFTS
(See page SA−20)
13. REMOVE FRONT EXHAUST PIPE
(a) Remove the 2 bolts and gasket from the exhaust pipe.
Torque: 48 N·m (490 kgf·cm, 35 ft·lbf)
HINT:
At the time of installation, please refer to the following item.
Replace used gasket with new gasket.
(b) Remove the 3 nuts, front exhaust pipe and gasket.
Torque: 62 N·m (630 kgf·cm, 46 ft·lbf)
HINT:
At the time of installation, please refer to the following item.
Replace used nuts and gasket with new nuts and gasket.
14. DISCONNECT SHIFT CONTROL CABLE
(a) Remove the nut from the control shaft lever.
Torque: 13 N·m (135 kgf·cm, 10 ft·lbf)
(b) Remove the clip and disconnect the control cable.
(c) Remove the 2 shift cable mounting bolts.
Torque: 7.0 N·m (75 kgf·cm, 65 in.·lbf)

Q08738
AX128−01
Q06066
Q06109
Q06077NRP AX−6
− AUTOMATIC TRANSAXLE (A540H)PARK/NEUTRAL POSITION (PNP) SWITCH
1996 RAV4 (RM447U)
PARK/NEUTRAL POSITION (PNP)
SWITCH
ON−VEHICLE REPAIR
1. REMOVE NO.2 ENGINE UNDER COVER
2. DISCONNECT PARK/NEUTRAL POSITION SWITCH
CONNECTOR
3. REMOVE PARK/NEUTRAL POSITION SWITCH
(a) Remove the nut and disconnect the shift control cable.
(b) Remove the nut and shift control lever.
(c) Using a screwdriver, pry off the lock plate.
(d) Remove the nut and lock plate.
(e) Remove the 2 bolts and pull out the park/neutral position
switch.
4. INSTALL AND ADJUST PARK/NEUTRAL POSITION
SWITCH
(a) Install the park/neutral position switch to the manual valve
shaft with the 2 bolts and nut.
(b) Install a new lock plate and tighten the nut.
Torque: 6.9 N·m (70 kgf·cm, 61 in.·lbf)
(c) Stake the nut with the lock plate.
(d) Temporarily install the manual valve lever shaft.
(e) Turn the lever counterclockwise until it stops, then turn it
clockwise 2 notches.
(f) Remove the shaft control lever.

Q06078
Neutral
Basic
Line
Groove
Q08738
− AUTOMATIC TRANSAXLE (A540H)PARK/NEUTRAL POSITION (PNP) SWITCH
AX−7
1996 RAV4 (RM447U)
(g) Adjust the park/neutral position switch
(See page AX−6).
HINT:
Align the groove and park/neutral basic line
(h) Tighten the 2 bolts.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
(i) Install the shaft control lever with the nut.
Torque: 12.7 N·m (130 kgf·cm, 9 ft·lbf)
(j) Connect the control cable with the nut.
5. CONNECT PARK/NEUTRAL POSITION SWITCH CON-
NECTOR
6. INSTALL NO.2 ENGINE UNDER COVER

D00694
OR0038
Z13387A B CDC
C
D00696
AX−10
− AUTOMATIC TRANSAXLE (A540H)VALVE BODY ASSEMBLY
1996 RAV4 (RM447U)
11. REMOVE VALVE BODY
(a) Remove the 10 bolts.
(b) Disconnect the throttle cable from the cam and remove
the valve body.
12. INSTALL VALVE BODY TO TRANSAXLE CASE
(a) While holding the cam down with your hand, slip the cable
end into the slot.
(b) Raise up the valve body into place.
NOTICE:
Do not entangle the solenoid wire.
(c) Install and tighten the 10 bolts.
Torque: 11 N·m (110 kgf·cm, 8 ft·lbf)
HINT:
Each bolt length is indicated below.
Hand−tighten the 10 bolts first, then torque with a torque
wrench.
Bolt length:
Bolt A: 22 mm (0.87 in.)
Bolt B: 32 mm (1.26 in.)
Bolt C: 43 mm (1.69 in.)
Bolt D: 55 mm (2.17 in.)
13. INSTALL B
3 APPLY PIPE
NOTICE:
Be careful not to bend or damage the pipe.