display TOYOTA RAV4 PLUG-IN HYBRID 2022 Owner's Manual

107
2 2-2. Charging
Plug-in hybrid system
*: Flashes for a certain period of time, and then turns off.
QCharging indicator of the charging port
When a system malfunction occurs while charging or using the Remote Air Condi-
tioning System, the charging indicator rapidly flashes for a certain period of time, and
then turns off.
If this occurs, when a door is opened with the power switch off, a message is dis-
played on the multi-information display. When a message is displayed, follow the
instructions displayed on the screen.
Illumination/flashing patternVehicle condition
Illuminated
Charging is in progress
Charging is possible
“Battery Heater” (P.127) is operating
“Battery Cooler” (P.128) is operating
Flashing (normally)*When charging schedule is registered (P.143) and
AC charging cable is connected to vehicle
Rapidly flashing*When charging cannot be carried out due to malfunc-
tion in a power source or the vehicle etc. (P.157)
Not illuminated
Charging connector is not inserted into AC
charging inlet
When the charging schedule (P.143) is on
standby
When charging is completed

1242-2. Charging
Ensure that the junction box is
equipped with a Residual Cur-
rent Circuit-Breaker (RCCB). If it
is not, have one installed by a
duly qualified professional.
When charging outdoors, make
sure to connect to a rain-tight
socket that is certified for outdoor
use. Checking Residual Current
Circuit-Breaker (RCCB) opera-
tion before its use is recom-
mended.
Check whether there are any
local EV-charging regulations in
place, and adhere to them.
*: For detailed information, consult an
electrician.
QThe charging environment
For safe charging, the following
charging equipment and settings are
recommended.
ORain-tight socket
When charging outdoors, connect the
plug to a rain-tight socket, and ensure
that the plug remains waterproof while
the plug is connected.
ODedicated circuit
• To reduce the risk of fire, connect only
to an at least 13A branch circuit with
an over-current protection.
• To reduce the risk of electric shock
when working with the plug, connect
to a socket that has a Residual Cur-
rent Circuit-Breaker (RCCB) installed.
ORemote switch
Allows the electricity from the socket to
be interrupted by operating a switch,
thus allowing safe removal and insertion
of the plug on rainy days.
QWhen your circuit breaker trips
during charging
The upper limit of the charging current
can be changed in “Vehicle Settings” on
the multi-information display.
1Press or of the meter control
switches to select .
2Press or of the meter control
switches to select “Vehicle Settings”,
and then press and hold .
3Press or of the meter control
switches to select “Charging Set-
tings”, and then press .
The “Charging Settings” screen will
be displayed.
4Press or of the meter control
switches to select “Charging Cur-
rent”, and then press .
The “Charging Current” screen will
be displayed.
5Press or of the meter control
switches to select “16A”
*1 or “8A”,
and then press .
During charging, the maximum
charging current will be restricted to
the set current or lower.
*2
If the breaker still trips while charging,
even after changing the upper limit of
the charging current, check if the con-
nected power source meets the speci-
fied charging conditions. (P.123)
*1: Vehicles with 6.6 kW onboard trac-
tion battery charger only
*2: Restricting the charging current will
lengthen the charging time.

127
2 2-2. Charging
Plug-in hybrid system
such as the remaining charge of the
hybrid battery (traction battery), the
outside temperature and specifica-
tions of an AC charger.
*4: When using “My Room Mode”
(P.152), the time required for
charging to complete may be longer
or the charging may not be com-
pleted.
*5: If equipped
QCharging time may increase
In the following situations, charging time
may become longer than normal:
OIn very hot or very cold temperatures.
OWhen the hybrid battery (traction bat-
tery) becomes hot, such as immedi-
ately after high-load driving.
OThe vehicle is consuming a lot of elec-
tricity, for example, when the head-
lights are on etc.
OWhen using “My Room Mode”.
(P.152)
OThere is a power outage during
charging.
OThere is an interruption in the electri-
cal supply.
OThere is a drop in the voltage of exter-
nal power source.
OThe charge in the 12-volt battery is
low, for example due to the vehicle
being left unused for a long period of
time.
OThe maximum charging current is set
to 8A or 16A* through “Vehicle Set-
tings”. (P.124)
OWhen the “Battery Heater” operates.
(P.127)
OWhen the “Battery Cooler” is operated
before charging. (P.128)
OWhen the plug generates heat due to
a loose socket connection etc.
*: Vehicles with 6.6 kW onboard traction
battery charger only
QUsing a DC Charger
DC Chargers cannot be used with this
vehicle.
QCharging electricity
This vehicle can be charged up to
approximately 3.3 kW or 6.6 kW
*.
However, depending on the used char-
ger or AC charging cable, charging elec-
tricity may be limited.
*: Vehicles with 6.6 kW onboard traction
battery charger only
This vehicle is equipped with sev-
eral functions that are linked with
charging.
Q“My Room Mode” (P.152)
When the AC charging cable is
connected to the vehicle, electrical
components such as the air condi-
tioning system or audio system can
be used using the external power
source
*.
*: The power of the hybrid battery (trac-
tion battery) may be used depending
on the situation.
Q“Battery Heater”
When the outside temperature is
low and the AC charging cable is
connected to the vehicle, this func-
tion automatically warms the hybrid
battery (traction battery) until it
reaches or exceeds a certain tem-
perature.
“Battery Heater” will operate when
the “Battery Heater” of the
“Charging Settings” on the multi-
information display is on. (P.185)
Charging-linked functions

1282-2. Charging
QHybrid battery (traction bat-
tery) warming control (Green-
land only)
This control operates after the AC
charging cable remains connected
to the vehicle for 3 days and “Bat-
tery Heater” automatically stops. It
automatically insulates the hybrid
battery (traction battery) in
extremely low temperatures.
This control stops 31 days after
the AC charging cable is con-
nected, even if it is still con-
nected to the vehicle.
When this control operates,
charging schedule settings are
ignored and charging starts.
Q“Battery Cooler”
When the hybrid battery (traction
battery) is hot and the AC charging
cable is connected to the vehicle,
this function cools the hybrid bat-
tery (traction battery) before
charging is carried out.
“Battery Cooler” will operate when
the “Battery Cooler” of the
“Charging Settings” on the multi-
information display is on. (P.185)
QTraction battery heating and cool-
ing system (“Battery Heater” and
“Battery Cooler”)
OThe system operates when the hybrid
battery (traction battery) is below or
above a certain temperature.
OThe system may operate when
charging is not being performed.
OWhen the charging schedule is used
(P.143), this function will operate according to the charging schedule.
Q“Battery Heater”
OWhen “Battery Heater” is operating,
the charging indicator illuminates.
OWhen the AC charging cable is
removed from the vehicle or remains
connected to the vehicle for approxi-
mately 3 days, the system automati-
cally stops.
OWhen “Battery Heater” is operating
during charging, the charging time
may be longer than normal.
OIf the outside temperature becomes
high while “Battery Heater” is operat-
ing, charging may complete earlier
than the “Departure” time set.
(P.143)
OWhen the traction battery is almost
completely charged, “Battery Cooler”
may not be implemented.
OWhen the following operations are
performed while “Battery Heater” is
operating, the hybrid battery (traction
battery) heating operation stops.
• The shift lever is changed to any posi-
tion other than P
• The Remote Air Conditioning System
is operated (P.414)
O“Battery Heater” may operate even
when the hybrid battery (traction bat-
tery) is fully charged depending on the
temperature of the hybrid battery
(traction battery).
• The remaining charge of the hybrid
battery (traction battery) decreases
when “Battery Heater” operates. The
charging operation may start again to
charge the hybrid battery (traction bat-
tery).
• “Charging Stopped Due to Pulled
Charging Connector” may be shown
when the charging connector is
removed while recharging. (P.159)
Q“Battery Cooler”
OThe charging indicator is illuminated
while “Battery Cooler” is on standby or
operating.
O“Battery Cooler” is implemented for a

1302-2. Charging
battery).
If there are no charging facilities at
your destination, the hybrid battery
(traction battery) can be charged
using the hybrid battery (traction
battery) charge mode. (P.87)
*
*: When using the hybrid battery (trac-
tion battery) charge mode while
parked, make sure that no flammable
objects are near the vehicle and the
vehicle is parked in a well-ventilated
area. (P.88)
QAfter returning home
In order to drive the next time,
charge the hybrid battery (traction
battery).
Settings the charging schedule allows
you to charge the hybrid battery (trac-
tion battery) at the desired time such as
late at night or early in the morning.
Furthermore, the charging schedule
can be set to automatically charge the
hybrid battery (traction battery) every
day or at the same time on certain
days. (P.143)
Information related to charging is
displayed and can be checked on
the multi-information display.
QWhile charging
When any door is opened during
charging, the current charging con-
dition and approximate time
remaining until charging is com-
plete are displayed for a certain
period of time.
QAfter charging is complete
When any door is opened with the
power switch off after charging is
complete, a message detailing the
results of the charging is displayed
for a while. Also, a message is dis-
played if an operation that stops
charging is performed or a situation
Checking information
related to charging

131
2
2-2. Charging
Plug-in hybrid system
where charging cannot be per-
formed occurs.
When a message is displayed, follow
the instructions displayed on the
screen. ( P.159)
QMulti-information display during charging
If approximately 100 seconds elapse
after the power switch is turned to ON during charging, the power switch will automatically turn off and the display will
disappear.
QSafety functions
OThe hybrid system will not start while the AC charging cable is attached to the vehicle, even if the power switch is
operated.
OIf the AC charging cable is connected
while the “READY” indicator is illumi- nated, the hybrid system will stop automatically and driving will not be
possible.
Things to know before
charging
Make sure to read the follow-
ing precautions before con-
necting the AC charging cable
to the vehicle and charging the
hybrid battery (traction bat-
tery).
WARNING
QCaution when charging
People with implantable cardiac pace-
makers or cardiac resynchronization therapy-pacemakers should not carry out the charging procedure. Ask
someone else to do it.
ODo not approach the charger and
AC charging cable while charging. Charging procedure may affect the operation of such devices.
ODo not remain in the vehicle during charging.
Charging procedure may affect the operation of such devices.
ODo not enter the vehicle even to take something out of the luggage compartment.
Charging procedure may affect the operation of such devices.

133
2 2-2. Charging
Plug-in hybrid system
each part of the AC charging cable
is in good condition. (P.116)
QDuring charging
OThe charging starting time may differ
depending on the state of the vehicle,
but this does not indicate a malfunc-
tion.
OCooling fan sounds may be heard
from near the rear seat. (P.98)
ODuring charging, sounds may be
heard from near the hybrid battery
(traction battery) in accordance with
the operation of the air conditioning
system or “Battery Cooler” (P.128).
ODuring and after charging, the rear
seat and its surrounding area in which
the onboard traction battery charger is
installed may get warm.
OThe surface of the CCID (Charging
Circuit Interrupting Device) may
become hot, but this does not indicate
a malfunction. (When using Mode 2
AC charging cable.)
ODepending on radio wave conditions,
interference may be heard on the
radio.
OThe current charging condition and
the estimated time until charging will
complete can be checked on the
multi-information display.
QCapacity reduction of the hybrid
battery (traction battery)
The capacity of the hybrid battery (trac-
tion battery) will decline gradually when
the hybrid battery (traction battery) is in
use. The rate at which it declines will dif-
fer in accordance with environmental
conditions and the way in which the
vehicle is used. Observing the following
can help suppress battery capacity
decline.
OAvoid parking the vehicle in areas with
a high temperature under direct sun-
light when the hybrid battery (traction
battery) is fully charged.
OAvoid accelerating and decelerating frequently and suddenly when EV
driving.
OAvoid frequent driving near the top
speed for EV driving. (P.90)
OLeave a low level of charge in the
hybrid battery (traction battery) when
leaving the vehicle undriven for a long
period of time.
After confirming that EV mode or
AUTO EV/HV mode has switched to
HV mode, turn the power switch off.
OUse the charging schedule function as
much as possible in order to fully
charge the hybrid battery (traction bat-
tery) immediately before starting off.
(P.143)
Also, if the hybrid battery (traction bat-
tery) capacity reduces, the distance that
can be driven in EV mode or AUTO
EV/HV mode decreases. However, vehi-
cle performance does not significantly
become worse.
QWhen the remaining charge of the
hybrid battery (traction battery) is
low after charging
In the following situations, the remaining
charge of the hybrid battery (traction
battery) after charging completes may
be less than normal in order to protect
the system (the EV driving range after
the battery is fully charged may be
shorter).
*
OCharging is carried out when the out-
side temperature is low or high.
OCharging is carried out immediately
after high-load driving or in extreme
heat.
When none of the above situations
apply and there is a drastic drop in the
remaining charge of the hybrid battery
(traction battery) after charging com-
pletes, have the vehicle inspected by
any authorized Toyota retailer or Toyota
authorized repairer, or any reliable
repairer.
*: When this occurs, even if the remain-
ing charge display of the hybrid bat-
tery (traction battery) shows that it is

137
2 2-2. Charging
Plug-in hybrid system
the charging connector is not locked.*
*
: If the charging connector is not firmly
inserted, locking operation will be
performed several times.
7If the charging indicator of the
charging port flashes after
inserting the charging connec-
tor:
The charging schedule is regis-
tered (P.143).
After temporarily removing the charging
connector, reinsert it within approxi-
mately 5 seconds. (P.137)
If the error warning indicator on the
CCID (Charging Circuit Interrupting
Device) flashes during charging, check
P.113 and follow the correction proce-
dure.
The charging indicator will turn off when
charging is completed.
The charging indicator will also turn off
when charging is stopped for some rea-
son before completion. In this case, refer to P.155.
QIf the charging indicator of the
charging port flashes after con-
necting the AC charging cable
The charging schedule (P.143) is reg-
istered and charging cannot be per-
formed. To cancel charging using the
charging schedule and start charging,
perform any of the following procedures.
OTurn “Charge Now” on (P.149)
OWhile the charging indicator is flash-
ing, remove and reconnect the
charging connector within 5 seconds
QWhen the charging connector can-
not be inserted into the AC
charging inlet
P.121
QCharging time
P.126
QSafety function
Charging will not start when the
charging connector is not locked. If the
charging indicator does not illuminate
even when the charging connector is
inserted, remove and reinsert the con-
nector, and then check that the charging
indicator of the charging port illuminates.
QCharging time may increase
P.127
QWhile charging
When the power switch is turned to ON
and the energy monitor is displayed on
the audio system screen, the charging
connector is displayed on the energy
monitor and the flow of electricity during

1382-2. Charging
charging is displayed ( P.193).
QCharging at a public charging sta-
tion with authentication function
When a door is unlocked during charging, the charging connector is
unlocked and charging will be stopped. In this case, the charging station authentication is canceled and charging
may not be able to restart. Reconnect the charging connector and perform authentication for the charging station.
QProtection function of AC charging
inlet overheating (vehicles with 6.6 kW onboard traction battery char-ger)
By installing a temperature sensor to the AC charging inlet, prevents parts from melting when the temperature rises due
to foreign matter entering the charging connector. When a certain temperature increase is detected, charging is
stopped immediately and a message is displayed on the multi-information dis-play. After the temperature has
decreased, charging resumes by per- forming the operation to start charging again.
WARNING
QWhen charging
Observe the following precautions.
Failure to do so may cause an unex-
pected accident, resulting in death or serious injury.
OConnect to a power source suitable
for charging. ( P.123)
OCheck that the AC charging cable,
plug and socket are free of foreign matter.
OBefore charging, check that the AC charging inlet is not deformed, damaged or corroded, and check
that the inlet is free of foreign mat- ter such as dirt, snow and ice. If there is dirt or dust in these areas,
remove completely before inserting the charging connector.
OBefore inserting the charging plug into the charger, make sure there is no dirt or dust on the terminal
areas. If there is dirt or dust in these areas, remove completely before inserting the charging plug.
ODo not get the terminals of the AC charging inlet wet.
OOnly use sockets where the plug can be securely inserted.
ODo not bundle or wind the AC charging cable while charging, as
doing so may result in overheating.
ODo not touch the terminals of the
charging connector and AC charging inlet with a sharp metal objects (needles etc.) or hands, or
short them with foreign objects.
OWhen charging outdoors, make
sure to connect to a rain-tight socket for outdoor use. Ensure the rain-tight cover closes completely. If
the rain-tight cover cannot be closed, install a rain-tight cover that will close.
OIn order to stop charging at the charging station, follow the instruc-
tions of the charger.
OIf any heat, smoke, odors, noise or
other abnormalities are noticed during charging, stop charging immediately.
ODo not insert the plug if the socket is submerged in water or snow.
OWhen charging while it is raining or snowing, do not connect or discon-
nect the plug if your hands are wet. Also, do not get the plug or outlet wet.
ODo not charge the vehicle during a lightning storm.
OPrevent the AC charging cable from being caught in the door or back
door.

143
2 2-2. Charging
Plug-in hybrid system
QCalendar settings
Current date and time information is
automatically set using GPS. However,
if GPS calibration of clock is turned off in
the multimedia system settings, the date
needs to be set on the multi-information
display.
If the calendar settings check screen is
displayed when an attempt was made to
register a charge schedule, check that
the correct date is set. If it is incorrect,
be sure to correct it.
If the calendar information is wrong, the
charging schedule function will not oper-
ate normally.
When registering the charging
schedule, the following settings can
be changed.
QSelect the charging mode
One of the two following charging
modes can be selected.
“Start”
Starts charging at the set time*1 and fin-ishes charging when fully charged.
*2
“Departure”
Starts charging to finish at the set
time.
*3, 4
When this setting is selected, the air
conditioning-linked function can be
used.
*1: Charging schedule function is per-
formed in accordance with the clock
in the multi-information display.
Before registering the charging
schedule, check the clock settings to
the proper time.
*2: There might be a slight error in the
timing when charging starts due to
the state of the hybrid battery (trac-
tion battery).
*3: When the system determines that
there is no time to finish charging by
the set scheduled departure time, it
starts charging. Check the charging
schedules.
*4: If sudden changes in temperature or
changes in the condition of the
power source occur while charging,
charging may not end exactly at the
time estimated by the system.
QRepeated setting
The periodic charging schedule can
be set by selecting your desired
day of the week. (If no days are
selected, charging is only carried
out once.)
QAir conditioning-linked set-
ting (“Climate Prep”)
When the charging mode is set to
“Departure”, the vehicle air condi-
tioning system (P.406) can be set
to automatically operate
* according
Using the charging
schedule function
Charging can be carried out at
the desired time by registering
the charging schedule. Also, it
is possible to set the charging
schedule to one’s prefer-
ences, such as having
charging complete by a certain
departure time or be carried
out at the same time on certain
days.
Settings of the charging
schedule function