headrest TOYOTA SEQUOIA 2001 Service User Guide

RS11E±01
H24319
H24339
H24338Hog Ring
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY (Manual Adjuster Type)
RS±67
3350 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
HINT:

Use the same procedures for the RH side and LH side.

The procedures listed below are for the LH side.
NOTICE:

If the side airbag assembly has been dropped, or
there are cracks, dents or other defects in the case or
connector, replace the side airbag assembly with a
new one.

When installing the side airbag assembly, take care
it is not pinched between other parts.

Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
1. INSTALL SEATBACK COVER
(a) Install the seatback cover to the seatback pad.
(b) Install the 2 headrest supports.
(c) Turn up the seatback cover and install the hog rings.
2. INSTALL SEATBACK COVER AND PAD
(a) Install the seatback cover and pad to the seat frame as-
sembly.
(b) Install the hog rings to the seat frame assembly.
(c) Install the hog rings to the seat frame assembly.

H24333
H24331ClawsClip
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY (Manual Adjuster Type)
RS±69
3352 Author: Date:
2005 SEQUOIA (RM1146U)
6. INSTALL VERTICAL ADJUSTER HANDLE
(a) Install the vertical adjuster handle with the 2 screws.
(b) Install the vertical adjuster handle cap.
7. INSTALL RECLINING ADJUSTER RELEASE HANDLE
8. INSTALL SEAT CUSHION OUTER SHIELD
Install the seat cushion outer shield with the screw.
9. INSTALL HEADREST
10. INSTALL FRONT SEAT
Mount the front seat to the vehicle.
NOTICE:
Be careful not to damage the body.
(a) w/ Side airbag:
Connect the airbag connector.
(b) Connect the connectors.
(c) Slide the front seat to the rearmost position.
(d) Tighten the bolts on the front side temporarily, starting
from the bolt on the inner side.
(e) Tighten them completely.
Torque: 37 N´m (377 kgf´cm, 27 ft´lbf)
(f) Slide the front seat to the foremost position.
(g) Tighten the bolts on the rear side temporarily, starting
from the bolt on the inner side.
(h) Tighten them completely.
Torque: 37 N´m (377 kgf´cm, 27 ft´lbf)
11. INSTALL SEAT TRACK COVERS
12. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
13. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
14. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)

BO4S6±01
H24329
37 (380, 27)
37 (380, 27)
37 (380, 27)
37 (380, 27)
37 (380, 27)
42 (430, 32) Seatback Cover
Seat Cushion
Cover
Seat Cushion
PadArmrest CapArmrest Spacer
Armrest
Lock Plate
Spacer
Armrest
AssemblyHeadrest
Headrest Support Seatback Pad
Lumbar Support
Adjuster
Seat Frame Assembly Seat Position Sensor
Protector
Seat Position
Sensor
Seat Cushion
Inner Shield
Seat Cushion
Lower ShieldFront Seat Inner BeltRH Reclining
Adjuster Inside
CoverRH Seatback
ShieldVertical Adjuster
Bracket Inner Cover
Vertical Adjuster
Bracket Outer Cover
LH Reclining
Adjuster Inside Cover
Reclining Knob
Slide Knob
Seat Cushion Outer ShieldLumbar Switch Power Seat SwitchLH Seatback Shield

Hog RingSeat Track
Cover
Seat Track
CoverBushing

Hog Ring
Non±reusable part: Specified torque
N´m (kgf´cm, ft´lbf)


w/ Side airbag:
5.5 (56, 49 in.´lbf)
w/ Seat heater:
w/ Seat heater:
Seat Cushion Heater Assembly
Seatback
Heater Assembly
Occupant Classification ECUPassenger's seat:
Driver's seat:
Driver's seat:
BO±110
± BODYFRONT SEAT (Power Adjuster Type)
3663 Author: Date:
2005 SEQUOIA (RM1146U)
FRONT SEAT (Power Adjuster Type)
COMPONENTS
HINT:
The procedures listed below are for the LH side.

BO4S8±01
H24311
H24312
H24313
BO±112
± BODYFRONT SEAT (Power Adjuster Type)
3665 Author: Date:
2005 SEQUOIA (RM1146U)
DISASSEMBLY
CAUTION:
Wear safety gloves, because the sharp edges and surfaces
of the seat frame may cause injury to the hands.
HINT:

The procedures listed below are for the LH side.

Tape the screwdriver tip before using it to remove the
parts.

For easy removal of the lumbar support adjuster, release
the lumbar support through lumbar switch operation.
1. REMOVE HEADREST
2. REMOVE SLIDE KNOB AND RECLINING KNOB
Using a screwdriver, remove the slide knob and reclining knob.
HINT:
Tape the screwdriver tip before use.
3. REMOVE SEAT CUSHION LOWER SHIELD, SEAT
CUSHION OUTER SHIELD AND SEAT CUSHION IN-
NER SHIELD
(a) Remove the screw from the seat cushion outer shield.
(b) Perform the same procedure on the seat cushion inner
shield.
(c) Remove the 2 screws from the seat cushion outer shield.
(d) Remove the screw from the seat cushion inner shield.

H24861
H24321
Hog Ring
H24318Hog Ring
H24319
H24320
BO±114
± BODYFRONT SEAT (Power Adjuster Type)
3667 Author: Date:
2005 SEQUOIA (RM1146U)
(c) w/ Side airbag:
Remove the nut and disconnect the seatback cover
bracket from the seat frame assembly.
(d) Remove the hog rings from the seat frame assembly.
(e) Remove the hog rings from the seat frame assembly.
(f) Remove the seatback cover and pad from the seat frame
assembly.
9. REMOVE SEATBACK COVER
(a) Turn up the seatback cover and remove the hog rings.
(b) Remove the 2 headrest supports.
(c) Remove the seatback cover from the seatback pad.
10. w/ Seat heater:
REMOVE SEATBACK HEATER ASSEMBLY
Cut off the tack pins which fasten the seat heater, and then re-
move the seatback heater assembly from the seatback cover.
11. REMOVE SEAT CUSHION COVER AND PAD
(a) Disconnect the wire harness clamp.
(b) Remove the 2 clips.

H24378
H24320
H24393
Listing Pocket
Seat WireSeat Heater
Tack Pin
Seatback Cover
A: Install the tack pins under the wire.A
Tack pins should not be beyond the seat.Upper
Name Stamp a±a:
Tack Pin
Seat Heater
b±b:
Tack Pin
Seat Heater
Tack Pina
ba
b
Seatback Coveraa
bb
b
bb bb
b
b b
bb
b
bbb
± BODYFRONT SEAT (Power Adjuster Type)
BO±119
3672 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Install the hog rings to the seat cushion cover.
(c) Install the 2 clips.
(d) Connect the wire harness clamp.
9. w/ Seat heater:
INSTALL SEATBACK HEATER ASSEMBLY
(a) Set the seatback heater assembly with the name stamp
side facing the seatback cover.
(b) Install the seatback heater assembly with the 11 tack
pins.
NOTICE:
Do not substitute other metal parts for tack pins.
10. INSTALL SEATBACK COVER
(a) Install the seatback cover to the seatback pad.
(b) Install the 2 headrest supports.

H24312
BO±122
± BODYFRONT SEAT (Power Adjuster Type)
3675 Author: Date:
2005 SEQUOIA (RM1146U)
(g) Install the screw to the seat cushion outer shield.
(h) Perform the same procedure on the seat cushion inner
shield.
17. INSTALL SLIDE KNOB AND RECLINING KNOB
18. INSTALL HEADREST

BO4SB±01
H24345
RH Lower Reclining
Adjuster Inside Cover
Seat Cushion
Outer Shield
Vertical Adjuster Handle Cap Reclining Adjuster Release Handle Seat Cushion
Inner ShieldRH Upper Reclining
Adjuster Inside Cover
RH Seat Cushion
Lower Shield
LH Lower Reclining
Adjuster Inside CoverLH Upper Reclining
Adjuster Inside CoverLH Seat Cushion
Lower Shield
Vertical Adjuster Handle
Non±reusable part: Specified torque
N´m (kgf´cm, ft´lbf)

Driver's seat:
Driver's seat:
37 (380, 27)
37 (380, 27)37 (380, 27)
37 (380, 27)
42 (430, 32) Seatback Cover
Seat Cushion
Cover
Seat Cushion
PadArmrest CapArmrest SpacerArmrest
Lock Plate
Spacer
Armrest AssemblyHeadrest
Headrest Support Seatback Pad
Seat Frame Assembly
Seat Position Sensor
Protector
Seat Position Sensor
Front Seat
Inner Belt
Hog RingSeat Track Cover
Seat Track Cover

Hog Ring
37 (380, 27)
Occupant Classification ECUPassenger's seat:
w/ Side airbag:
5.5 (56, 49 in.´lbf)
BO±124
± BODYFRONT SEAT (Manual Adjuster Type)
3677 Author: Date:
2005 SEQUOIA (RM1146U)
FRONT SEAT (Manual Adjuster Type)
COMPONENTS
HINT:
The procedures listed below are for the LH side.

BO4SD±01
H24331ClawsClip
H24332
H24333
H24334ClawsClip BO±126
± BODYFRONT SEAT (Manual Adjuster Type)
3679 Author: Date:
2005 SEQUOIA (RM1146U)
DISASSEMBLY
CAUTION:
Wear safety gloves, because the sharp edges and surfaces
of the seat frame may cause injury to the hands.
HINT:

The procedures listed below are for the LH side.

Tape the screwdriver tip before using it to remove the
parts.
1. REMOVE HEADREST
2. REMOVE SEAT CUSHION OUTER SHIELD
(a) Remove the screw from the seat cushion outer shield.
(b) Using a screwdriver, remove the seat cushion outer
shield.
HINT:
Tape the screwdriver tip before use.
3. REMOVE RECLINING ADJUSTER RELEASE HANDLE
4. REMOVE VERTICAL ADJUSTER HANDLE
(a) Using a screwdriver, remove the vertical adjuster handle
cap.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 2 screws and the vertical adjuster handle.
5. REMOVE SEAT CUSHION INNER SHIELD
(a) Remove the screw from the seat cushion inner shield.
(b) Using a screwdriver, remove the seat cushion inner
shield.
HINT:
Tape the screwdriver tip before use.
6. REMOVE FRONT SEAT INNER BELT
(a) Disconnect the wire harness clamps and connectors.
(b) Remove the nut and front seat inner belt.

H24319
H24335
H24336
H24395
H24342
BO±128
± BODYFRONT SEAT (Manual Adjuster Type)
3681 Author: Date:
2005 SEQUOIA (RM1146U)
9. REMOVE SEATBACK COVER
(a) Turn up the seatback cover and remove the hog rings.
(b) Remove the 2 headrest supports.
(c) Remove the seatback cover from the seatback pad.
10. REMOVE SEAT CUSHION COVER AND PAD
(a) Remove the clip.
(b) Perform the same procedure on the other side.
(c) Remove the hog rings from the seat cushion cover.
(d) Unlatch the seat cushion cover hooks, then remove the
seat cushion cover with seat cushion pad.
11. REMOVE SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from the seat
cushion pad.
12. REMOVE RH AND LH UPPER RECLINING ADJUSTER
INSIDE COVERS
(a) Remove the screw and LH upper reclining adjuster inside
cover.
(b) Perform the same procedure on the other side.