TOYOTA SEQUOIA 2001 Service Repair Manual

CO0UZ±05
B04067Air HoleWa t e r
Hole
P21661
P21660
B07456
± COOLINGWATER PUMP
CO±7
2823 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECT WATER PUMP
(a) Visually check the air hole and water hole for coolant leak-
age.
If leakage is found, replace the water pump and timing belt.
(b) Turn the pulley, and check that the water pump bearing
moves smoothly and quietly.
If necessary, replace the water pump.
2. INSPECT FLUID COUPLING
(a) Remove the 4 nuts and fan from the fluid coupling.
(b) Check that the fluid coupling is not damaged and that no
silicon oil leaks.
If necessary, replace the fluid coupling.
(c) Reinstall the fan to the fluid coupling with the 4 nuts.
Torque: 8.5 N´m (85 kgf´cm, 75 in.´lbf)
3. INSPECT FAN PULLEY BRACKET
Check the turning smoothness of the fan pulley.
If necessary, replace the pulley bracket.
4. INSPECT TIMING BELT COMPONENTS
(See page EM±21)

CO0IT±06
B04463
Connect
New O±Ring
B03030
Seal Width
2 ± 3 mm
New O±Ring
CO±8
± COOLINGWATER PUMP
2824 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
1. INSTALL WATER PUMP
(a) Install a new O±ring to the water bypass pipe end.
(b) Apply soapy water to the O±ring.
(c) Connect the water pump to the water bypass pipe end.
(d) Install the water pump and a new gasket with the 5 bolts,
2 stud bolts and nut. Uniformly tighten the bolts, stud bolts
and nut in several passes.
Torque:
Bolt: 21 N´m (215 kgf´cm, 15 ft´lbf)
Stud bolt and nut: 18 N´m (185 kgf´cm, 13 ft´lbf)
2. INSTALL WATER INLET AND INLET HOUSING AS-
SEMBLY
(a) Remove any old packing (FIPG) material and be careful
not to drop any oil on the contact surfaces of the water in-
let housing and water pump.

Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket sur-
faces and sealing groove.

Thoroughly clean all components to remove all the
loose material.

Using a non±residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the sealing groove of water inlet
housing as shown in the illustration.
Seal packing: Part No. 08826±00100 or equivalent

Install a nozzle that has been cut to a 2 ± 3 mm (0.08
± 0.12 in.) opening.

Parts must be assembled within 3 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.

Immediately remove nozzle from the tube and rein-
stall cap.
(c) Install a new O±ring to the water inlet housing.
(d) Apply soapy water on the O±ring.
(e) Attach the water inlet housing end to the front water by-
pass joint hole.

B17478
AB
± COOLINGWATER PUMP
CO±9
2825 Author: Date:
2005 SEQUOIA (RM1146U)
(f) Install the water inlet and housing assembly with the 2
bolts. Alternately tighten the bolts.
Torque: 18 N´m (185 kgf´cm, 13 ft´lbf)
HINT:
Each bolt length is indicated in the illustration.
Bolt length:
76 mm (3.00 in.) for A
22 mm (0.87 in.) for B
(g) Connect the water bypass hose to the water inlet housing.
3. INSTALL NO.2 IDLER PULLEY (See page EM±23)
4. INSTALL TIMING BELT (See page EM±23)
5. FILL WITH ENGINE COOLANT
6. START ENGINE AND CHECK FOR ENGINE COOLANT
LEAKS
7. RECHECK ENGINE COOLANT LEVEL

CO0IU±07
B05865
Water InletThermostat

Gasket
N´m (kgf´cm, ft´lbf) : Specified torque

Non±reusable part
19 (195, 14)
CO±10
± COOLINGTHERMOSTAT
2826 Author: Date:
2005 SEQUOIA (RM1146U)
THERMOSTAT
COMPONENTS

CO0IV±04
B05866
± COOLINGTHERMOSTAT
CO±11
2827 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
HINT:
Removal of the thermostat would have an adverse effect, caus-
ing a lowering of cooling efficiency. Do not remove the thermo-
stat, even if the engine tends to overheat.
1. DRAIN ENGINE COOLANT
2. DISCONNECT WATER INLET FROM WATER INLET
HOUSING
Remove the 3 nuts and disconnect the water inlet from the wa-
ter inlet housing.
3. REMOVE THERMOSTAT
(a) Remove the thermostat.
(b) Remove the gasket from the thermostat.

CO0IW±08
P08849
CO0929
CO0949
Valve Lift CO±12
± COOLINGTHERMOSTAT
2828 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
INSPECT THERMOSTAT
HINT:
The thermostat is numbered with the valve opening tempera-
ture.
(a) Immerse the thermostat in water and gradually heat the
water.
(b) Check the valve opening temperature.
Valve opening temperature: 80 to 84°C (176 to 183°F)
If the valve opening temperature is not as specified, replace the
thermostat.
(c) Check the valve lift.
Valve lift: 10 mm (0.39 in.) or more at 95°C (203°F)
If the valve lift is not as specified, replace the thermostat.
(d) Check that the valve is fully closed when the thermostat
is at low temperatures (below 40°C (104°F)).
If not closed, replace the thermostat.

CO0IX±05
B07218
Jiggle Valve30°30°
± COOLINGTHERMOSTAT
CO±13
2829 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
1. PLACE THERMOSTAT IN WATER INLET HOUSING
(a) Install a new gasket to the thermostat.
(b) Insert the thermostat into the water inlet housing with the
jiggle valve facing straight upward.
HINT:
The jiggle valve may be set within 30° of either side of the pre-
scribed position.
2. INSTALL WATER INLET
Install the water inlet with the 3 nuts.
Torque: 19 N´m (195 kgf´cm, 14 ft´lbf)
3. FILL WITH ENGINE COOLANT
4. START ENGINE AND CHECK FOR COOLANT LEAKS
5. RECHECK ENGINE COOLANT LEVEL

B14807
CO1B9±02
CO±14
± COOLINGRADIATOR
2830 Author: Date:
2005 SEQUOIA (RM1146U)
RADIATOR
ON±VEHICLE CLEANING
INSPECT FINS FOR BLOCKAGE
If fins are clogged, wash them with water or a steam cleaner and
dry with compressed air.
NOTICE:

If the distance between the steam cleaner and the
core is too close, there is a possibility of damaging
the fin, so keep the following injection distance.
Injection PressureInjection Distance
2,942 to 4,903 kpa
(30 to 50 kg/cm2,
427 to 711 psi)300 mm (11.811 in)
4,903 to 7,845 kpa
(50 to 80 kg/cm2,
711 to 1,138 psi)500 mm (19.685 in)

If the fins are bent, straighten them with a screwdriver
or pliers.

Never apply water directly onto the electronic compo-
nents.

CO0IZ±08
CO1242
Radiator Cap Tester
Radiator Cap
30° or More
B07240
Radiator Cap Tester
± COOLINGRADIATOR
CO±15
2831 Author: Date:
2005 SEQUOIA (RM1146U)
ON±VEHICLE INSPECTION
1. REMOVE RADIATOR CAP
CAUTION:
To avoid the danger of being burned, do not remove the ra-
diator cap while the engine and radiator are still hot, as fluid
and steam can be blown out under pressure.
2. INSPECT RADIATOR CAP
NOTICE:

If the radiator cap has contaminations, always rinse
it with water.

Before using a radiator cap tester, wet the relief valve
and pressure valve with engine coolant or water.

When performing steps (a) and (b) below, keep the
tester at an angle of over 30° above the horizontal.
(a) Using a radiator cap tester, slowly pump the tester and
check that air is coming from the vacuum valve.
Pump speed: 1 push/(3 seconds or more)
NOTICE:
Push the pump at a constant speed.
If air is not coming from the vacuum valve, replace the radiator
cap.
(b) Pump the radiator cap tester, and measure the relief valve
opening pressure.
Pump speed: 1 push within 1 second
NOTICE:
This pump speed is for the first pump only (in order to close
the vacuum valve). After this, the pump speed can be re-
duced.
Opening pressure:
Standard74 to 103 kPa (0.75 to 1.05 kgf/cm2,10.7 to 14.9 psi)
Minimum59 kPa (0.6 kgf/cm2, 8.6 psi)
HINT:
Use the tester's maximum reading as the opening pressure.
If the opening pressure is less than minimum, replace the radia-
tor cap.
3. INSPECT COOLING SYSTEM FOR LEAKS
(a) Fill the radiator with coolant and attach a radiator cap tes-
ter.
(b) Warm up the engine.
(c) Pump it to 118 kPa (1.2 kgf/cm
2, 17.1 psi), and check that
the pressure does not drop.
If the pressure drops, check the hoses, radiator or water pump
for leaks. If no external leaks are found, check the heater core,
cylinder block and head.
4. REINSTALL RADIATOR CAP

CO1D2±01
B07246
Radiator Assembly
A/T Oil Cooler Hose
Engine Under Cover (4WD)Upper Radiator Hose
Lower Radiator Hose
x 5
N´m (kgf´cm, ft´lbf) : Specified torque
12 (120, 9)
No.1 Fan Shroud
No.2 Fan Shroud
Engine Under Cover (2WD)
Clip
Clip
CO±16
± COOLINGRADIATOR
2832 Author: Date:
2005 SEQUOIA (RM1146U)
COMPONENTS