TOYOTA SEQUOIA 2001 Service Repair Manual

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±589
783 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
TFT (transmission fluid temperature)Less than 20°C (68°F)
(varies with TFT (transmission fluid temperature) at engine start)
WIRING DIAGRAM
See page DI±582.
INSPECTION PROCEDURE
HINT:
According to the DATA LIST displayed by the OBD II scan tool or hand±held tester, you can read the value
of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of
troubleshooting is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the OBD II scan tool or hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the ºONº button of the OBD II scan tool or the hand±held tester.
(f) When you use the hand±held tester:
Select the item ºDIAGNOSIS / ENHANCED OBD II / DATA LISTº.
(g) According to the display on the tester, read the ºDATA LISTº.
ItemMeasurement Item/
Range (display)Normal Condition
AT FLUID TEMP 1
ATF Temp. Sensor Value/
min.: ±40C (±40F)
max.: 215C (419F)
After Stall Test;
Approx. 80C (176F)

Equal to ambient temperature when cold soak
HINT:
When DTC P0712 is output and hand±held tester output is 150C (302F) or more, there is a short circuit.
When DTC P0713 is output and hand±held tester output is ±40C (±40F), there is an open circuit.
Measure the resistance between terminal THO1 (OT) and body ground.
Temperature DisplayedMalfunction
±40°C (±40°F)Open circuit
150°C (302°F) or moreShort circuit
HINT:
If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 second).
When P0713 is set, P0711 cannot be detected.
It is not necessary to inspect the circuit when P0711 is set.

DI±590
± DIAGNOSTICSAUTOMATIC TRANSMISSION
784 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check other DTCs output (in addition to DTC P0711).
PREPARATION:
(a) Turn the ignition switch off.
(b) Connect the OBD II scan tool or hand±held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Turn on the tester.
(e) Select the item ºDIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODESº.
CHECK:
Read the DTCs using the OBD II scan tool or the hand±held tester.
RESULT:
Display (DTC output)Proceed to
Only ºP0711º is outputA
ºP0711º and other DTCsB
HINT:
If any other codes besides ºP0711º are output, perform troubleshooting for those DTCs first.
B Go to DTC chart (See page DI±573).
A
2 Check transmission fluid level (See page DI±524).
OK:
Automatic transmission fluid level is correct.
NG Add fluid
(See page DI±524).
OK
Replace the transmission wire (ATF tempera-
ture sensor) (See page AT±7).

D14162
Clutch Drum
(Timing Rotor)
Input Speed Sensor NT
(Transmission Revolution Sensor NT)Output Speed Sensor SP2
(Transmission Revolution Sensor SP2)
Parking Gear
(Timing Rotor)
D14148
GND
1 V/DIV
2 ms/DIV
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±591
785 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0717 Input Speed Sensor Circuit No Signal
CIRCUIT DESCRIPTION
This sensor detects the rotation speed of the turbine which shows the input revolution of transmission. By
comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (SP2), the ECM
detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure ac-
cording to various conditions, thus, providing smooth gear shift.
DTC No.DTC Detection ConditionTrouble Area
P0717
All conditions below are detected for 5 secs. or more
(1±trip detection logic)
(a) Gear change is not performed
(b) Gear position: 4th or 5th
(c) T/M input shaft rpm: 300 rpm or less
(d) T/M output shaft rpm: 1,000 rpm or more
(e) Park/neutral position switch:

NSW input signal is OFF

R input signal is OFF

L input signal is OFF
(f) Shift solenoid valves, park/neutral position switch and ve-
hicle speed sensor are in normal operation

Open or short in speed sensor (NT) circuit

Speed sensor (NT)

ECM

Automatic transmission (clutch, brake or gear, etc.)
Reference (Using an oscilloscope):
Check the waveform between terminals NT+ and NT± of
the ECM connector.
Standard: Refer to the illustration.
TerminalNT+ ± NT±
Tool setting1V/DIV, 2ms/DIV
Vehicle conditionEngine idle speed (P or N position)
DIDJ8±01

DI±592
± DIAGNOSTICSAUTOMATIC TRANSMISSION
786 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR DESCRIPTION
This DTC indicates that pulse is not output from the speed sensor NT (Turbine (input) speed sensor ) or is
output only little. The NT terminal of the ECM detects the revolving signal from the speed sensor (NT) (input
RPM). The ECM outputs a gearshift signal comparing the
input speed sensor (NT) with the output speed
sensor (SP2).
While the vehicle is operating in the 4th or 5th gear position in the shift position of D, if the input shaft revolu-
tion is less than 300 rpm
*1 although the output shaft revolution is more than 1000 rpm or more*2, the ECM
detects the trouble, illuminates the MIL and stores the DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is approx. 50 km/h (31 mph) or more.
MONITOR STRATEGY
Related DTCsP0717Speed sensor (NT)/Verify pulse input
Rid /C tMainSpeed sensor (NT)Required sensors/ComponentsSubSpeed sensor (NO)
Frequency of operationContinuous
Duration5 sec.
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not present.See page DI±545
Shift changeShift change is completed and before starting next shift change operation
ECM selected gear4th or 5th
Output shaft rpm1,000 rpm or more±
NSW switchOFF
R switchOFF
L switchOFF
EngineRunning
Ignition switchON
StarterOFF
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
Sensor signal rpmLess than 300 rpm
COMPONENT OPERATING RANGE
ParameterStandard value
Speed sensor (NT)Input speed is equal to engine speed when lock±up ON.

D14163
ECM
NT+
NT± 35
WB
1 2E7
E7 O1
O/D Direct Clutch Speed Sensor
(Input Speed Sensor NT)
E1 27
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±593
787 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
According to the DATA LIST displayed by the OBD II scan tool or hand±held tester, you can read the value
of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of
troubleshooting is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the OBD II scan tool or hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the ºONº button of the OBD II scan tool or the hand±held tester.
(f) When you use the hand±held tester:
Select the item ºDIAGNOSIS / ENHANCED OBD II / DATA LISTº.
(g) According to the display on the tester, read the ºDATA LISTº.
ItemMeasurement Item/
Range (display)Normal Condition
SPD (NT)Input Turbine Speed/
display: 50 r/min
[HINT]

Lock±up ON (After warming up the engine);
Input Turbine speed (NT) equal to the engine
speed.

Lock±up OFF (Idling at N position);
Input Turbine speed (NT) nearly equal to the en-
gine speed.
HINT:

SPD (NT) is always 0 while driving:
Open or short in the sensor or circuit.

SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph)
or more:
Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

D14164OK NG
5.4 N´m
(55 kgf´cm, 48 in.´lbf)
No Clearance
D14165
Sensor Side:
(Connector Front View):
21 O1
DI±594
± DIAGNOSTICSAUTOMATIC TRANSMISSION
788 Author: Date:
2005 SEQUOIA (RM1146U)
1 Inspect speed sensor installation.
PREPARATION:
Jack up the vehicle.
CHECK:
Check the speed sensor (NT) installation.
OK:
The installation bolt is tightened properly and there is
no clearance between the sensor and transmission
case.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
NG Replace speed sensor NT (See page AT±5).
OK
2 Inspect speed sensor NT.
PREPARATION:
Disconnect the speed sensor connector from the transmission.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
20 C (68 F)
1 ± 2560 to 680 W
NG Replace speed sensor NT (See page AT±5).
OK

D14166
ECM:
NT+NT±E8E7E6E5E4
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±595
789 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check harness and connector (ECM ± speed sensor NT).
PREPARATION:
(a) Connect the speed sensor connector.
(b) Disconnect the ECM connector.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
20C (68F)
E7 ± 35 (NT+) ± E7 ± 27 (NT±)560 to 680 W
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
E7 ± 35 (NT+) ± Body ground10 kW or higher
E7 ± 27 (NT±) ± Body ground=
NG Repair or replace the harness or connector
(See page IN±35).
OK
Replace the ECM (See page SF±80).

D14162
Clutch Drum
(Timing Rotor)
Input Speed Sensor NT
(Transmission Revolution Sensor NT)Output Speed Sensor SP2
(Transmission Revolution Sensor SP2)
Parking Gear
(Timing Rotor)
C13480D14149
GND
2 V/DIV
20 ms/DIV
DI±596
± DIAGNOSTICSAUTOMATIC TRANSMISSION
790 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0722 Output Speed Sensor Circuit No Signal
CIRCUIT DESCRIPTION
The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the
ECM. The ECM determines the vehicle speed based on these signals. An AC voltage is generated in the
speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assy rotates, and this voltage
is sent to the ECM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.
The gear shift point and lock±up timing are controlled by the ECM based on the signals from this vehicle
speed sensor and the throttle position sensor signal.
DTC No.DTC Detection ConditionTrouble Area
P0722
All conditions below are detected 500 times or more continu-
ously (1±trip detection logic)
(a) No signal from speed sensor (SP2) is input to ECM while 4
pulses of No. 1 vehicle speed sensor signal are sent
(b) Vehicle speed is 9 km/h (6 mph) or more for at least 4 sec.
(c) Park/neutral position switch is OFF.
(d) Transfer position is except neutral (4WD).

Open or short in speed sensor (SP2) circuit

Speed sensor (SP2)

ECM

Automatic transmission (clutch, brake or gear, etc.)
Reference (Using an oscilloscope):
Check the waveform between terminals SP2+ and SP2±
of the ECM connector.
Standard: Refer to the illustration.
TerminalSP2+ ± SP2±
Tool setting2V/DIV, 20ms/DIV
Vehicle conditionVehicle speed 20 km/h (12 mph)
DIDJ9±01

D14163
ECM
SP2+
SP2± 34
26
Y±R W±R
1 2E7
E7
E1 V2
Vehicle Speed Sensor (SP2)
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±597
791 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR DESCRIPTION
The output speed sensor SP2 monitors the output shaft speed. The ECM controls the gearshift point and
the lock up timing based on the signals from the output speed sensor SP2 and throttle position sensor.
If the ECM detects no signal from the output shaft speed sensor SP2 even while the vehicle is moving, it
will conclude that is a malfunction of the output speed sensor SP2. The ECM will illuminate the MIL and set
a DTC.
MONITOR STRATEGY
Related DTCsP0722Speed sensor SP2/Verify pulse input
Required sensors/ComponentsSpeed sensor SP2
Frequency of operationContinuous
Duration500 output shaft revolution
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not present.See page DI±545
Vehicle speed sensor pulse input4
Vehicle speed range (4 sec. or more)9 km/h (5.59 mph) or more±
NSW switchOFF
Battery voltage8 V or more±
Ignition switchON
StarterOFF
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
Output speed sensor pulse inputNo input
WIRING DIAGRAM

D14164OK NG
5.4 N´m
(55 kgf´cm, 48 in.´lbf)
No Clearance
DI±598
± DIAGNOSTICSAUTOMATIC TRANSMISSION
792 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
According to the DATA LIST displayed by the OBD II scan tool or hand±held tester, you can read the value
of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of
troubleshooting is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the OBD II scan tool or hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the ºONº button of the OBD II scan tool or the hand±held tester.
(f) When you use the hand±held tester:
Select the item ºDIAGNOSIS / ENHANCED OBD II / DATA LISTº.
(g) According to the display on the tester, read the ºDATA LISTº.
ItemMeasurement Item/
Range (display)Normal Condition
SPD (SP2)
Output shaft Speed/
min.: 0 km/h (0 mph)
max.: 255 km/h (158 mph)Vehicle stopped: 0 km/h (0 mph)
[HINT]
Equal to vehicle speed
HINT:

SPD (SP2) is always 0 while driving:
Open or short in the sensor or circuit.

SPD (SP2) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph)
or more:
Sensor trouble, improper installation, or intermittent connection trouble of the circuit.
1 Inspect speed sensor installation.
PREPARATION:
Jack up the vehicle.
CHECK:
Check the speed sensor (SP2) installation.
OK:
The installation bolt is tightened properly and there is
no clearance between the sensor and transmission
case.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
NG Replace speed sensor SP2 (See page AT±5).
OK