O2 sensor TOYOTA SEQUOIA 2001 Service Repair Manual

H01017H43107H23603
Airbag
Sensor
Assembly P/T Squib LH
C D
PL± PL+
Service Wire
P10
DI±1478
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1672 Author: Date:
2005 SEQUOIA (RM1146U)
11 Check airbag sensor assembly.
PREPARATION:
(a) From the step 6:
Turn the ignition switch to the LOCK position.
(b) From the step 6:
Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) Connect the connectors to the airbag sensor assembly.
(d) Using a service wire, connect P10±1 (PL+) and P10±2
(PL±) of connector ºCº.
NOTICE:

Twist the end of the service wire in order to insert it
into the connector.

Do not forcibly insert the twisted service wire into the
terminals of the connector when connecting.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1906, B1907 or B1908 is not output.
HINT:
Codes other than DTC B1906, B1907 and B1908 may be out-
put at this time, but they are not related to this check.
NG Replace airbag sensor assembly
(see page RS±82).
OK

H01018H23474
Airbag
Sensor
Assembly DC P/T Squib LH
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1479
1673 Author: Date:
2005 SEQUOIA (RM1146U)
12 Check front seat outer belt LH (P/T squib LH).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) From the step 10:
Disconnect the service wire from connector ºCº.
(d) Connect the connector to the front seat outer belt LH.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1905, B1906, B1907 or B1908 is not output.
HINT:
Codes other than DTC B1905, B1906, B1907 and B1908 may
be output at this time, but they are not related to this check.
NG Replace front seat outer belt LH
(see page BO±163).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
HINT:

Perform the simulation method by selecting the check mode with the hand±held tester (see page
DI±1151).

After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page DI±1151).

DI±1480
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1674 Author: Date:
2005 SEQUOIA (RM1146U)
DTC Normal Source Voltage Drop
CIRCUIT DESCRIPTION
The SRS is equipped with a voltage±increase circuit (DC±DC converter) in the airbag sensor assembly in
case the source voltage drops.
When the battery voltage drops, the voltage±increase circuit (DC±DC converter) functions to increase the
voltage of the SRS to normal voltage.
A malfunction in this circuit is displayed differently from other codes. The source voltage drop is indicated
when the SRS warning light comes on without showing any DTCs.
A malfunction in this circuit is not recorded in the airbag sensor assembly. The SRS warning light automati-
cally goes off when the source voltage returns to normal.
DTC No.Detection Item
(Normal)Source voltage drop
DIDHS±01

H24000
Airbag Sensor
Assembly
IG2 A20 B
Engine Room J/B Instrument Panel J/B
Instrument Panel J/B I18
Ignition SW
21
1A3
1J7 1C2
1C3 AM2 IG2B±R
6 5IGN1
AM2
2C1
2D1 W±R W±R
B
4
5
BF10
Fusible Link
BlockE1
E2 A2025
A2026 W±B
W±B 1A6
1F9
1F 10
1A8 W±B
W±B A
A J8
J/C
IE Battery
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1481
1675 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

H23040
IG2
A20
DI±1482
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1676 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
CAUTION:
Be sure to perform the following procedures before troubleshooting to avoid unexpected airbag de-
ployment.
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the connectors from the airbag sensor assembly.
(d) Disconnect the connectors from the steering wheel pad.
(e) Disconnect the connectors from the front passenger airbag assembly.
(f) w/ Side and curtain shield airbag:
Disconnect the connectors from the side airbag assembly LH and RH.
(g) w/ Side and curtain shield airbag:
Disconnect the connectors from the curtain shield airbag assembly LH and RH.
(h) Disconnect the connectors from the front seat outer belt LH and RH.
1 Check battery.
CHECK:
Measure the voltage of the battery.
OK:
Voltage: 11 to 14 V
NG Replace battery.
OK
2 Check source voltage (power source).
PREPARATION:
Connect the negative (±) terminal cable to the battery, and wait
for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position.
(b) Measure the voltage according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
A20±21 (IG2) ±
Body groundIgnition switch ON10 to 14 V
NG Repair or replace wire harness (battery ± airbag
sensor assembly).
OK

H23040E2E1
A20
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1483
1677 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check wire harness (airbag sensor assembly ± body ground).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
A20±25 (E1) ±
Body groundAlwaysBelow 1 W
A20±26 (E2) ±
Body groundAlwaysBelow 1 W
NG Repair or replace wire harness.
OK

DI±1484
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1678 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check SRS warning light.
PREPARATION:
(a) Connect the connectors to the airbag sensor assembly.
(b) Connect the connectors to the steering wheel pad.
(c) Connect the connectors to the front passenger airbag assembly.
(d) w/ Side and curtain shield airbag:
Connect the connectors to the side airbag assembly LH and RH.
(e) w/ Side and curtain shield airbag:
Connect the connectors to the curtain shield airbag assembly LH and RH.
(f) Connect the connectors to the front seat outer belt LH and RH.
(g) Connect the negative (±) terminal cable to the battery, and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at least 6 seconds.
(b) Operate all components of the electrical system (defogger, wiper, headlight, heater blower, etc.) and
check the SRS warning light operation.
OK:
The SRS warning light does not come on.
NG Replace airbag sensor assembly
(see page RS±82).
OK
END

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1489
1683 Author: Date:
2005 SEQUOIA (RM1146U)
8 Check connectors.
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
CHECK:
Check the connectors are properly connected to the occupant classification ECU and the 4 occupant classifi-
cation sensors.
OK:
The connectors are connected.
PREPARATION:
Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.
CHECK:
Check the connectors are not damaged or deformed.
OK:
The connectors are normal.
NG Repair or replace connector, then go to step 1.
OK
9 Check DTC.
PREPARATION:
(a) Connect the connectors to the occupant classification ECU and the 4 occupant classification sensors.
(b) Connect the negative (±) terminal cable to the battery.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC is not output.
NG Replace airbag sensor assembly
(see page RS±82).
OK

H23996
LA
A2014
ABR I18
Ignition SW
Combination Meter
BatteryIG2 A2021
E1 A2025
E2 A2026 B
W±B
W±B B±R
IG2 AM26 5 W±R
SRS B±Y
C5 29
C612 C6241D4
1A5 1A3
IGN1
1D6
1F9
101A6
1A8 Instrument Panel J/B
Engine Room J/B1H11
1J7
2C1
2D1AM2BR
W±B
W±B
J8
J/C A
A 4
5 B
BB±O
IEAirbag Sensor
Assembly
1C2
Instrument Panel J/B
F10
Fusible Link Block 1C3 D6
DLC3
114B10
4A20
4A10B±Y
B±Y
1F W±R Sub J/B No. 4 DI±1492
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1686 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1493
1687 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check battery.
CHECK:
Measure the voltage of the battery.
OK:
Voltage: 11 to 14 V
NG Replace battery.
OK
2 Check connection of connectors.
PREPARATION:
Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
CHECK:
Check that the connectors are properly connected to the airbag sensor assembly and combination meter.
OK:
The connectors are connected securely.
NG Connect connectors.
OK
3 Prepare for inspection.
CAUTION:
Be sure to perform the following procedures before troubleshooting to avoid unexpected airbag de-
ployment.
(a) Disconnect the connectors from the airbag sensor assembly.
(b) Disconnect the connectors from the steering wheel pad.
(c) Disconnect the connectors from the front passenger airbag assembly.
(d) w/ Side and curtain shield airbag:
Disconnect the connectors from the side airbag assembly LH and RH.
(e) w/ Side and curtain shield airbag:
Disconnect the connectors from the curtain shield airbag assembly LH and RH.
(f) Disconnect the connectors from the front seat outer belt LH and RH.
NEXT