set clock TOYOTA SOLARA 2008 Owners Manual (in English)

’08 Solara_U (L/O 0802)
180
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
TUNE·FILE (Tuning and File up/down)
Radio
Turn the “TUNE·FILE” knob clockwise to
step up the frequency. Turn the knob
counterclockwise to step down the fre-
quency.
XM Satellite Radio
∗—
Turn the “TUNE·FILE” knob clockwise to
step up the channel. Turn the knob coun-
terclockwise to step down the channel.
∗: Use of satellite radio requires XM 
tuner and service. Contact your Toyota
dealer for details.
MP3/WMA player
Turn the “TUNE·FILE” knob clockwise to
file up. Turn the knob counterclockwise to
file down.
Some parts of the audio system can be
adjusted using the switches on the steer-
ing wheel.
Details of the specific switches, controls,
and features are described below. 1. Volume control switch
2. “ ” switch
3. “MODE” switch 1. Volume control switch
Push “+” side to increase the volume. The
volume continues to increase while the
switch is being pushed.
Push “ −” side to decrease the volume.
The volume continues to decrease while
the switch is being pushed.
2. “   ” switch
Radio
This switch has the following features—
To select a preset station:
Quickly push and release the “ ” or “ ”
side of the switch. Do this again to select
the next preset station.
To seek a station:
Push and hold the “ ” or “” side of the
switch until you hear a beep. Do this
again to find the next station. If you push
the switch on either side during the seek
mode, seeking will be cancelled.
To step up or down the frequency, push
and hold the switch even after you hear
a beep. When you release the switch, the
radio will begin seeking up or down for a
station. Do this again to find the next
station.
Audio remote controls
(steering switches)

’08 Solara_U (L/O 0802)
238
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
The following information is displayed
on the multiinformation displays.1. Cruise information
2. Clock
3. Outside temperature When the engine switch is on, the last
previously used mode displayed just be-
fore the engine switch is off will appear.
If the electrical power source has been
disconnected from the multi
−information
display, the display will automatically be
set to the initial mode.
CAUTION
Do not adjust the display while the
vehicle is moving. Be sure to adjust
the display only when the vehicle is
stopped.
SELECTING UNIT
You can select the unit between En-
glish/U.S. customary system and metric
unit.
To select the unit A (English/U.S. custom-
ary system) or unit B (metric unit), push
and hold the “H” and “M” buttons beside
the clock for about 3 second.
The unit variations are as follows;
Information
Unit AUnit B
Average and
instantaneous
fuel consumption
MPGL/100km
Driving rangemilekm
Average vehicle
speedMPHkm/h
Outside
temperatureFC
This function is also linked with the auto-
matic air conditioning display.
Multiinformation displays—

’08 Solara_U (L/O 0802)
241
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
The center display indicates the time
when the engine switch is in the “ACC”
or “ON” position.
To reset the hour: Push the “H” button.
To reset the minutes: Push the “M” button.The right side display indicates the out-
side air temperatures when the engine
switch is in the “ON” position.
The displayed temperature ranges from
−30 C ( −22 F) up to 50 C (122 F).
If an abnormality exists in the connection
of the outside air temperature sensor, “ −−”
will appear on the display. If “ −−” appears
on the display, contact your Toyota dealer.
There may be a case that “−−” appears
momentarily when the ignition is quickly
turned to “ON”. It is normal if it goes out
soon.The direction is indicated on the inside
rear view mirror.
If the engine switch was turned off with
the system on, the system will automati-
cally turn back on when the engine switch
is turned on.
Push the “AUTO” switch for longer than 3
seconds to turn the compass system on
and off.
—Clock —Outside temperatureCompass

’08 Solara_U (L/O 0802)
366
2008 CAMRY SOLARA from Feb. ’08 Prod. (OM33810U)
2. Turn the bulb base counterclockwiseto the front of the vehicle as shown.
The above illustration shows the left −hand
headlight.3. Unplug the connector while depress- ing the lock release.
If the connector is tight, wiggle it.4. Plug in a new bulb into the connec- tor and install it into the mounting
hole.
Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact your Toyota dealer.