TOYOTA SUPRA 1995 Service Repair Manual

Check D squib.
(1) Turn ignition switch to LOCK.
(2) Disconnect negative (±) terminal cable from the
battery, and wait at least 90 seconds.
(3) Connect steering wheel pad connector.
(4) Connect negative(±) terminal cable to battery,
and wait at least 2 seconds.
(1) Turn ignition switch to ACC or ON and wait at
least 20 seconds.
(2) Clear malfunction code stored in memory.
(See page RS±47)
(3) Turn ignition switch to LOCK, and wait at least
20 seconds.
(4) Turn ignition switch to ACC or ON, and wait at
least 20 seconds.
(5) Using SST, connect terminals Tc and E
1 of
DLC1 or DLC2.
SST 09843±18020
(6) Check diagnostic trouble code.
Diagnostic trouble code 11 is not output.
Codes other than code 11 may be output at this time,
but they are not relevant to this check.
Check P squib.
Replace steering wheel pad.
Replace front passenger airbag assembly.
(1) Turn ignition switch to LOCK.
(2) Disconnect negative (±) terminal cable from the
battery, and wait at least 90 seconds.
(3) Connect front passenger airbag assembly
connector.
(4) Connect negative(±) terminal cable to battery,
and wait at least 2 seconds.
(1) Turn ignition switch to ACC or ON and wait at
least 20 seconds.
(2) Clear malfunction code stored in memory.
(See page RS±47)
(3) Turn ignition switch to LOCK, and wait at least
20 seconds.
(4) Turn ignition switch to ACC or ON, and wait at
least 20 seconds.
(5) Using SST, connect terminals Tc and E1 of
DLC1 or DLC2.
SST 09843±18020
(6) Check diagnostic trouble code.
Diagnostic trouble code 11 is not output.
Codes other than code 11 may be output at this
time, but they are not relevant to this check. RS±58
± SUPPLEMENTAL RESTRAINT SYSTEMTROUBLESHOOTING

Check front airbag sensor.
Replace front airbag sensor.
Disconnect front airbag sensor connector.
Measure resistance between each terminal of front
airbag sensor.

Do not press ohmmeter probes too strongly
against terminals of front airbag sensor.

Make sure the front airbag sensor connector
is properly connected.
Repair or replace harness or connector between center airbag sensor assembly and front airbag
sensor (See page RS±36).
Disconnect connector between center airbag sen-
sor assembly and spiral cable.
Measure resistance between D+, D± on spiral cable
side of connector between spiral cable and steering
wheel pad and body ground.
Resistance: 1 M or Higher
Check spiral cable.
Repair or replace spiral cable.
Repair or replace harness or connector between
center airbag sensor assembly and spiral cable.
 
 
 
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check. If the malfunctioning part cannot be
detected by the simulation method, replace all SRS components including the wire harness.
± SUPPLEMENTAL RESTRAINT SYSTEMTROUBLESHOOTINGRS±59

DTC 12 Short in Squib Circuit (to B+)
CIRCUIT DESCRIPTION
The squib circuit consists of the center airbag sensor assembly, spiral cable, steering wheel pad and front pas-
senger airbag assembly. It causes the SRS to deploy when the SRS deployment conditions are satisfied.
The front airbag sensor detects the deceleration force in a frontal collision and is located in the front fender on
the left and right sides.
For details of the function of each component, see FUNCTION OF COMPONENTS on page RS±4.
Diagnostic trouble code 12 is recorded when a B+ short is detected in the squib circuit or the front airbag sensor
circuit.
 DTC No. Diagnosis 
 
 
 
 
 
12
 
 
 
 
 
 

Short circuit in squib wire harness (to B +).


Squib malfunction.


Short circuit in front airbag sensor + S wire harness (to B +).


Front airbag sensors malfunction.


Spiral cable malfunction.


Center airbag sensor assembly malfunction.
RS±60± SUPPLEMENTAL RESTRAINT SYSTEMTROUBLESHOOTING

Preparation.
Disconnect center airbag sensor assembly connec-
tor.
Measure resistance between terminals +SR and
±SR, +SL and ±SL of harness side connector of
center airbag sensor assembly.
Resistance: 755
Ð 855

Repair or replace harness or connector between
center airbag sensor assembly and front airbag
sensor (See page RS±36).
Check front airbag sensor circuit. (Measure resistance between terminals
+SR and ±SR, +SL and ±SL of center airbag sensor assembly connector.)
Check front airbag sensor circuit. (Measure resistance between terminals
+SR or +SL of center airbag sensor assembly connector and body ground.)
(1) Disconnect negative (±) terminal cable from the
battery, and wait at least 90 seconds.
(2) Remove steering wheel pad (See page RS±10).
(3) Disconnect connector of front passenger airbag
assembly (See page RS±20).
Store the steering wheel pad with the front surface
facing upward.
Go to code 15.
(1) Connect negative (±) terminal cable to battery.
(2) Turn ignition switch ON.
Measure voltage between terminals +SR or +SL of
harness side connector of center airbag sensor as-
sembly and body ground.
Voltage: 0 Ð 0.1 V
INSPECTION PROCEDURES [P] Preparation [C] Check
± SUPPLEMENTAL RESTRAINT SYSTEMTROUBLESHOOTINGRS±61

Check D squib circuit.
For the connector for the center airbag sensor as-
sembly side) between center airbag sensor assem-
bly and front passenger airbag assembly, measure
the voltage between P
+ and body ground.
Voltage: 0 V
Check P squib circuit.
Disconnect center airbag sensor assembly connec-
tor.
For the connector (on the spiral cable side) between
the spiral cable and steering wheel pad, measure
the voltage between D
+ and body ground.
Voltage: 0 V
Repair or replace harness or connector between
the center airbag sensor assembly and front pas-
senger airbag sensor assembly.
RS±62± SUPPLEMENTAL RESTRAINT SYSTEMTROUBLESHOOTING

Check center airbag sensor assembly.
(1) Turn ignition switch to LOCK.
(2) Disconnect negative (±) terminal cable from the
battery.
(3) Connect connector to center airbag sensor as±
sembly.
(4) Using a service wire, connect P+ and P± on
center airbag sensor assembly side of connec±
tor between center airbag sensor assembly and
from passenger airbag assembly.
(5) Using a service wire, connect P+ and P± on
center airbag sensor assembly side of connec±
tor between center airbag sensor assembly and
front passenger airbag assembly.
(6) Connect negative (±) terminal cable to battery,
and wait at least 2 seconds.
(1) Turn ignition switch to ACC or ON and wait at
least 20 seconds.
(2) Clear malfunction code stored in memory.
(See page RS±47)
(3) Turn ignition switch to LOCK, and wait at least
20 seconds.
(4) Turn ignition switch to ACC or ON, and wait at
least 20 seconds.
(5) Using SST, connect terminals Tc and E
1 of
DLC1 or DLC2.
SST 09843±18020
(6) Check diagnostic trouble code.
Diagnostic trouble code 12 is not output.
Codes other than code 12 may be output at this
time, but they are not relevant to this check.
Replace center airbag sensor assembly.
± SUPPLEMENTAL RESTRAINT SYSTEMTROUBLESHOOTINGRS±63

Check D squib.
(1) Turn ignition switch to LOCK.
(2) Disconnect negative (±) terminal cable from the
battery, and wait at least 90 seconds.
(3) Connect steering wheel pad connector.
(4) Connect negative (±) terminal cable to battery,
and wait at least 2 seconds.
(1) Turn ignition switch to ACC or ON and wait at
least 20 seconds.
(2) Clear malfunction code stored in memory.
(See page RS±47)
(3) Turn ignition switch to LOCK, and wait at least
20 seconds.
(4) Turn ignition switch to ACC or ON, and wait at
least 20 seconds.
(5) Using SST, connect terminals Tc and E
1 of
DLC1 or DLC2.
SST 09843±18020
(6) Check diagnostic trouble code.
Diagnostic trouble code 12 is not output.
Codes other than code 12 may be output at this
time, but they are not relevant to this check.
Check D squib.
(1) Turn ignition switch to LOCK.
(2) Disconnect negative (±) terminal cable from the
battery, and wait at least 90 seconds.
(3) Connect front passenger airbag assembly con±
nectar.
(4) Connect negative (±) terminal cable to battery,
and wait at least 2 seconds.
(1) Turn ignition switch to ACC or ON and wait at
least 20 seconds.
(2) Clear malfunction code stored in memory.
(See page RS±47)
(3) Turn ignition switch to LOCK, and wait at least
20 seconds.
(4) Turn ignition switch to ACC or ON, and wait at
least 20 seconds.
(5) Using SST, connect terminals Tc and E
1 of
DLC1 or DLC2.
SST 09843±18020
(6) Check diagnostic trouble code.
Diagnostic trouble code 12 is not output.
Codes other than code 12 may be output at this
time, but they are not relevant to this check.
Replace steering wheel pad.
Replace front passenger airbag assembly. RS±64
± SUPPLEMENTAL RESTRAINT SYSTEMTROUBLESHOOTING

 
 
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.
Check spiral cable.
Repair or replace spiral cable.
Repair or replace harness or connector between
center airbag sensor assembly and spiral cable.
(1) Turn ignition switch to LOCK.
(2) Disconnect connector between center airbag
sensor assembly and spiral cable.
(3) Turn ignition switch ON.
Measure voltage at D
+ on spiral cable side of connec-
tor between spiral cable and steering wheel pad.
Voltage: 0 V
± SUPPLEMENTAL RESTRAINT SYSTEMTROUBLESHOOTINGRS±65

DTC 13 Short in D Squib Circuit (Between D+
Wire Harness and D±
Wire Harness)
CIRCUIT DESCRIPTION
The D squib circuit consists of the center airbag sensor assembly, spiral cable and steering wheel pad.
It causes the airbag to deploy when the airbag deployment conditions are satisfied.
For details of the function of each component, see FUNCTION OF COMPONENTS on page RS±4.
Diagnostic trouble code 13 is recorded when a short is detected in the D
+ wire harness and D± wire harness
of the squib circuit.
 
 DTC No.
 
 Diagnosis
 
 
 
 
13
 
 
 
 

Short circuit between D+ wire harness and D± wire harness of squib.


D squib malfunction.


Spiral cable malfunction.


Center airbag sensor assembly malfunction.
RS±66± SUPPLEMENTAL RESTRAINT SYSTEMTROUBLESHOOTING

INSPECTION PROCEDURES [P] Preparation [C] Check
Preparation.
(1) Disconnect negative (±) terminal cable from the
battery, and wait at least 90 seconds.
(2) Remove steering wheel pad (See page RS±10).
(3) Disconnect connector of front passenger airbag
assembly (See page RS±20).
Check D squib circuit.
For the connector (on the spiral cable side) be-
tween the spiral cable and steering wheel pad,
measure the resistance between D
+ and D±.
Resistance: 1 k
or higher.
Store the steering wheel pad with the front surface
facing upward.
± SUPPLEMENTAL RESTRAINT SYSTEMTROUBLESHOOTINGRS±67