TOYOTA T100 1997 Owners Manual

187
NOTICE
5VZ-FE engine vehicles for Canada:
When adding washer fluid, be careful not to spill the fluid over thedaytime running light resistor.
The following illustrations show how to
gain access to the bulbs. When replacing a bulb make sure the ignition swithc and
light switch are off. Use bulbs with the wattage ratings given in the table.
Halogen bulbs have pressurized
gas inside and require special han-
dling. They can burst or shatter ifscratched or dropped. Hold a bulb
only by its plastic or metal case. Do
not touch the glass part of a bulb
with bare hands. CAUTION
!
NOTICE
Only use a bulb of the listed type.
Light bulbsBulb
No.WType
Headlights900360/55A
Parking lights1685C
Front turn signal lights115627B
Rear turn signal lights115627B
Stop and tail lights115727/8B
Back-up lights115627B
High mounted stop- light1685C
License plate lights1685C
Interior lightÐ8D
Personal lightsÐ5D
Glovebox lightÐ5C
Step lightsÐ5C
A: HB2 halogen bulbs B: Single end bulbs
C: Wedge base bulbsD: Double end bulbs
Replacing light bulbsÐ

188
1. Open the hood. Unplug the con-nector. Remove the rubber cover.
If the connector is tight, wiggle it.2. Remove the rubber cover.3. Release the bulb retaining spring and remove the bulb. Install a new
bulb and the bulb retaining spring.
To install a bulb, align the tabs of the bulb with the cutouts of the mounting hole.
ÐHeadlights

189
4. Install the rubber cover andsnuggle on the boss.
Make sure the rubber cover fits snugly on
the connector and the headlight body.5, Install the plastic cover with the ONº mark upward and turn it
clockwise. Insert the connector.
Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact your Toyota dealer.Use a Phillips-head screwdriver.
ÐParking lights

190
Use a Phillips-head screwdriver.Use a Phillips-head screwdriver.
ÐRear turn signal, stop and
tail and back-up lights
ÐFront turn signal lights

191
a: Rear turn signal light
b: Stop and tail light
c: Back- up light
ÐLicense plate lights
ÐHigh mounted stoplight

192

Part 8193
SPECIFICATIONS
Dimensions and weight
Engine
Fuel
Service specifications
Tires
Fuses

194
Normal cab modelsXtra-cab models
Two-wheel drive modelsFour-wheel drive
modelsTwo-wheel drive modelsFour-wheel drive
models
Overall length mm(in.)5310 (209.1)5310 (209.1)5310 (209.1)5310 (209.1)
Overall width mm(in.)1910 (75.2)1910 (75.2)1910 (75.2)1910 (75.2)
Overall heightÐmm(in.) Unladen vehicle1710 (67.2) *1
1720 (67.6) *2
1730 (68.2) *31790 (70.6)*5
1820 (71.6) *71730 (68.2)*4
1740 (68.6) *51840 (72.6)*
5
1870 (73.5) *7
Wheelbase mm(in.)3095 (121.9)3095 (121.9)3095 (121.9)3095 (121.9)
Front tread mm(in.)1565 (61.6)*4
1570 (61.8) *51605 (63.2)
*5
1635 (64.4) *71565 (61.6)
*4
1570 (61.8) *51605 (63.2)
*5
1635 (64.4) *7
Rear tread mm(in.)1615 (63.6)*4
1625 (64.0) *51615 (63.6)*5
1650 (65.0) *71615 (63.6)*4
1625 (64.0) *51615 (63.6)*5
1650 (65.0) *7
Cargo weight rating
kg(lb.)498 (1100)*6
907 (2000) *3498 (1100)498 (1100)498 (1100)
*1
: 1/2-ton models with P215/75R15 tires
*2 : 1/2-ton models with P235/75R15 tires
*3 : 1-ton models
*4 : With P215/75R15 tires
*5 : With P235/75R15 tires
*6 : 1/2-ton models
*7 : With P265/70R16 tires
Dimensions and weight

195
Model:
3RZ-FE and 5VZ-FE
Type: 3RZ-FE engine4 cylinder in line, 4 cycle, gasoline
5VZ-FE engine 6 cylinder V type, 4 cycle, gasoline
Bore and stroke, mm (in.):
3RZ-FE engine95.0 x 95.0 (3.74 x 3.74)
5VZ-FE engine
93.5 x 82.0 (3.68 x 3.23)
Displacement, cm 3
(cu. in.):
3RZ-FE engine
2694 (164.3)
5VZ-FE engine 3378 (206.1) Fuel type:
Unleaded gasoline, Research Octane Number 91 (Octane Rating 87) orhigher
Fuel tank capacity, L (gal., Imp. gal.):
91 (24.0, 20.0) ENGINE
Valve clearance (engine cold), mm (in.)
3RZ-FE engines
Intake 0.15 '0.25 (0.006 '0.010)
Exhaust 0.25 '0.35 (0.010 '0.014)
5VZ-FE engine
Intake 0.13 '0.23 (0.006 '0.009)
Exhaust 0.27 '0.37 (0.011 '0.014)
Spark plug type: 3RZ-FE engines
NIPPONDENSO K16R-U
NGK BKR5EYA
5VZ-FE engine
NIPPONDENSO K16TR11
NGK BKR5EKB11
Spark plug gap:
3RZ-FE engine 0.8 (0.031)
5VZ-FE engine 1.1 (0.043)
Drive belt tension measured with
Boroughs drive belt tension gauge No.
BT-33-73F (used belt), Ibf:
3RZ-FE engine 115 + 20
5VZ-FE engine 100 + 20
Fuel
Engine Service specifications

196ENGINE LUBRICATION Oil capacity (drain and refill), L (qt., Imp. qt.):
Two-wheel drive models3RZ-FE engine With filter 5.5 (5.8, 4.8) Without filter 4.8 (5.1, 4.2)
5VZ-FE engine With filter 5.2 (5.5, 4.6) Without filter 4.9 (5.2, 4.3)
Four-wheel drive models With filter 4.7 (5.0, 4.1)Without filter 4.4 (4.7, 3.9)
Oil grade:
API SH, Energy- Conserving IIº multi-
grade engine oil or ILSAC multigrade
engine oil is recommended.
Recommended oil viscosity (SAE):
COOLING SYSTEM
Total capacity, L (qt., Imp. qt.): Two-wheel drive modelsWith manual transmission
3RZ-FE engine8.7 (9.2, 7.7)
5VZ-FE engine 10.0 (10.6, 8.8)
With automatic transmission 3RZ-FE engine
9.0 (9.5, 7.9)
5VZ-FE engine
9.9 (10.5, 8.7)
Four-wheel drive models
With manual transmission10.0 (10.6, 8.8)
With automatic transmission 9.9 (10.5, 8.7)
Coolant type: With ethylene-glycol antifreeze (Do not use alcohol type.)
BATTERY ÐMaintenance type battery
Specific gravity reading at 20 C (68 F):
1.260 Fully charged
1.160 Half charged
1.060 Discharged ÐNon-maintenance battery Open voltage* at 20
C (68 F):
12.7 V Fully charged
12.3 V Half charged
11.9 V Discharged
* Voltage that is checked 20 minutes after the key is removed with all the
lights turned off
Charging rates: Non-maintenance battery 5 A max. Maintenance type batteryQuick charge 15 A max.
Slow charge 5 A max.
CLUTCH
Pedal freeplay, mm (in.): 5' 15 (0.2 '0.6)
Fluid type:
SAE J1703 or FMVSS No. 116 DOT 3
MANUAL TRANSAXLE
Oil capacity, L (qt., Imp. qt.): 3RZ-FE engine
2.6 (2.7, 2.3)
5VZ-FE engine
Two-wheel drive models2.6 (2.7, 2.3)
Four-wheel drive models 2.2 (2.3, 1.9)