key TOYOTA TACOMA 2008 Accessories, Audio & Navigation (in English)

4
Answer KeyDown Key
Device IDBLU Logic XXXX
Pass Key 1234
Up Key
BLU Logic is a hands-free phone system
for your vehicle. BLU Logic connects
to any hand held cell phone device
equipped with
Bluetooth
® Wireless tech-
nology hands free profile and eliminates
the need to hold a handheld cell phone,
wear a headset, earpiece, or an in vehicle
mounted hand-set adapter while making
or receiving calls.

Getting Started
First, your Hands-free equipped cell
phone must be paired or electronically
matched to the BLU Logic unit. Then
simply place your phone anywhere in the
passenger compartment of your vehicle.
Your Hands-free equipped cell phone
will automatically connect or transmit
to the BLU Logic unit every time it is
on, charged, or within range (30ft/10
meters). To Pair your phone, please see
Pairing Guide on page 6
The system can pair up to 7 hand-sets.
For a list of compatible phones please
go to http://www.blulogicupdate.com
Quick-Start Guide

5
Making and Answering Calls
ToKey Do
Answer a Call Short Press
Ending a Call Short Press
Reject a Call Press for 2
seconds and
release when you hear 1 beep
Redial
the Last
Number Press for 2
seconds and
release when you hear 1 beep
Voice
Dialing Short Press
In a Call
To
Key Do
Adjust the Volume Up Short Press
Manual Pairing
To
Key Do
Pairing 
Press for 8 seconds
and release when
you hear 3 beeps. The system will
enter pairing mode for the next 5 minutes.
Memory Erase Press for 15
seconds and
release when you hear 4 beeps
Adjust the Volume Down Short Press
Transfer
a Call to Handset Press for 4
seconds and
release when you hear 2 beeps
Call
Waiting 
or

When a call waiting
tone is heard press
either volume but -
ton for 8 seconds
(approx.) to switch
to the other call.
Quick-Start Guide

6

Pairing your phone is simple, just
follow these steps:
The system can pair up to 7 hand-sets.
For a list of compatible phones please
go to http://www.blulogicupdate.com
1. Place your hand-set near the dash
board no more than 3 feet/1 meter apart.
2. Press and hold
key down for 8
seconds (approximately) until you hear
3 short beeps (this puts the system into
pairing mode for 5 minutes).
3. Activate your mobile hand-set’s
Hands-free accessing function by refer-
ring to your mobile hand-set user guide
for details. The hand-set will search for
accessible Hands-free devices.
Note:
For most phones, the pairing operation
will be as follows:
Search for a new device New
Handfree search. This will vary
depending on the features of your par-
ticular phone.
Pairing Guide

1
2
4. To pair another phone, repeat steps
1 through 3.
Pairing Order:

7
Pairing Order Continued:6. Press “Return” to go back to your hand-
set’s main menu. You should, now be
able to make and receive calls through the
system within a distance of approximately
30 ft./10 meters (obstructions may cause
this distance to be shorter)
Pairing Note:
Some manufacturer’s hand-sets do
not allow automatic connection to
Hands-free devices. If your hand-set
does not connect automatically, please
check to see if the auto-connect feature
has been enabled or set to Without
Confirmation. Other possible settings
may be: Required Authorization NO,
Device AuthorizedYES, Connection
AuthorizedYES, or Trusted
Device YES.
Please refer to your hand-set’s user
manual for further details.
Pairing Guide

3
5. Select “BLU Logic XXXX” from the
list. Enter the pre-programmed passkey
“1234” and press “OK” to pair the kit and
the hand-set. When pairing is completed,
you may hear a long beep. Now the sys-
tem is in standby mode (for most mobile
hand-sets a headset icon will be shown on
the screen).

8

Cannot find the Hands-free menu:
Please refer to your hand-set user manu-
al for assistance on various phones.
Hand-set will not pair:
1. Make sure that the phone and vehicle
ignition is ON. Also make sure that the
phone battery is charged.
2. Ensure your mobile hand-set’s
Hands-free feature is activated and en-
abled. Please refer to your mobile hand-
set user guide for specific instructions.
3. Ensure the BLU Logic system is
within a maximum of 3 feet/1 meter
of your mobile hand-set and there
are no obstructions in between such
as other electronic devices (this may
cause reduced range or interference in
transmission.)
4. Delete all paired devices by momen
-
tarily pressing the  key for 15 seconds.
Reference back to pairing once this is
done.
5. Your phone’s software may need to
be reset. Please remove and reinstall
battery and try again. 6. Delete all paired devices from your
hand-set and try again. There is a pos-
sibility that your hand-set is paired to too
many devices and exceeds the maximum
number of connections.
7. If all the above steps do not resolve
your problem, power off the vehicle for a
while. The BLU Logic is compliant with
and adopts the Hands-free Specification
V2.1. However, interoperability be-
tween the device and other Hands-free
enabled products is not guaranteed
because of various hand-sets features.
Please check with the manufacturer for
more information about compatibility &
use of your Hands-free devices
.
The system can pair up to 7 hand-sets.
For a list of compatible phones please go to http://www.blulogicupdate.com
My hand-set is paired with the kit.
However, when I start the car, it
doesn’t connect automatically:
Please refer to the Pairing Note men-
tioned on the left.
Pairing Troubleshooting

10(B.) If the phone does not automatically
disconnect Select “disconnect” from your
hand-set menu. See your hand-set user
manual for more details.


Using The System

(1) Voice Dial:
If your mobile’s hand-set is voice dial
enabled, when in standby mode, press the
 key. When you hear a beep’ from your
hand-set, say the voice tag.
Note:
BLU Logic does not have voice dial feature
but is compatible with equipped phones.
A) Please make sure there are voice tags
recorded into the mobile hand-set before
using voice dialing function. This function
is only applicable to mobile hand-sets with
Hands-free Profile. Because of variations
among different hand-sets you may not hear
a beep. Please refer to your mobile hand-
set’s user guide for additional information.
(3) Disconnection:
Follow these steps to disconnect the kit
from the current paired hand-set.
(A) Power off the vehicle. Phone should
automatically disconnect.
Using The System
13
3
No Phone 2 in car, Phone 1
connects
Only Phone 3 in car, Phone 3 connects

11
B.) When streaming music,
due to varia-
tions in different hand-set profiles, music
streaming may not resume after the key is
pressed.
(2) Call Answer:
Press the key to accept a call, or answer
via your mobile hand-set in the normal way.
(3) Call End:
Press the key to end a call, or end via your
mobile hand-set in the normal way.
(4) Call Reject:

Press and hold the key for 2 seconds (ap-
proximately) until you hear a short beep,
then release the key.
(5) Last Number Re-Dial:
In standby mode, press key for 2 seconds
(approx.) until you hear a short beep, then
release the key.
Note:
When streaming music, due to variations of different hand-set profiles, music streaming
may not resume after key is pressed.
(6) Mute & Un-mute:
When a conversation is in progress, you can
mute or un-mute the microphone so that the
other party cannot hear you.
To Mute:
Press and hold the keys
simultaneously for 2 seconds (approx.)
until you hear 1 beep from the speaker, then
release.
To Un-Mute: Press and hold the keys
simultaneously for 2 seconds (approx.)
until you hear 1 beep from the speaker, then
release.
(7) Volume Adjustment:

When a conversation is in progress, press
the volume upor downkeys repeatedly
until you reach the desired volume level.
Using The System

12
Using The System
Continued:
(8) Call Interchange:
When a conversation is in progress, you
may transfer the call in between the system
and hand-set.
System to Hand-set: Press key for 4 sec-
onds and release when you hear 2 beep’s.
Hand-set to System: Press key for 4
seconds and release when you hear 2 beep’s
or restart the vehicle.
Note:
This could vary owing to various hand-sets
features.
(9)Call Waiting:
When a call waiting tone is heard from your
hand-set, press either the volume up ▲or
volume down
 button for
8 seconds (approx.) to switch to the other
call. Repeat the same procedure to switch
back to the first call. (10) Music Stream & Pause:
After completion of Hands-free connec-
tion to an A2DP hand-set, you may listen
to music stored on your hand-set through
the vehicle’s speakers. Simply activate the
music streaming application on your hand-
set. Refer to your hand-set’s user manual
for more details.
Note:
Sound output is through the front speakers
only.
(11) Automatic Switch between Music
Stream & Calls:
When streaming hand-set music via the car
speakers, during an incoming call, music
will be paused. You may answer the call via
the system. Music stream will resume after
completion of the call.