ECO mode TOYOTA tC 2012 Accessories, Audio & Navigation (in English)

Page 7 SCION SECURITY SYSTEM
OPERATION
PASSIVE (AUTOMATIC) ARMING & DISARMING
When the Scion Security is programmed to PASSIVELY ARM, the system will ARM after
the ignition key is removed and all doors and the trunk are closed; you \
do not need to
lock the doors. When you come back to your vehicle and open a door, you must insert
the key into the ignition switch and turn it to “ON” during the EN\
TRY DELAY (0, 15 or 30
seconds), or an ALARM will be TRIGGERED. If you lock the doors, regular ARMING will
override PASSIVE ARMING; there will be no ENTRY DELAY. See the PROGRAMMING
information on page 12 to activate the PASSIVE ARMING mode, as well as to select
the ENTRY DELAY time. (Not applicable to vehicles with Smart Key system. Please
consult your Scion Dealer for programming information.)

To PASSIVELY ARM the system:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors. (The system will not
ARM while any of the doors are open.)
Close the trunk or hatch, if necessary. (The system will not ARM
while the trunk or hatch is open.)
After the last door, trunk or hatch is closed:
The STATUS MONITOR’S LED turns on for 30 seconds,
then starts flashing.**
The system is now ARMED.
To DISARM the PASSIVELY ARMED system:
Enter the vehicle through a front door.
The ENTRY DELAY begins: The STATUS MONITOR’S LED turns on (no flashing).
Insert the key into the ignition switch and turn it to “ON” before\

the ENTRY DELAY ends.* The LED turns off. The system is now DISARMED.
You may also DISARM the system following any of the methods
described on page 6.
NOTE: If your vehicle’s tail and marker lights turn on for 2 seconds when the ignition key is turned to “ON”, the TRIGGER MEMORY was activated; something
TRIGGERED an ALARM while you were away from the vehicle.
* If the ENTRY DELAY time elapses be-
fore the ignition switch is turned to “ON”,
an ALARM will be TRIGGERED. To
DISARM the system during an ALARM,
insert the ignition key and turn it to “ON”,
or press and release the remote control’s
unlock button.
** For some vehicles the LED will turn off
instead of flashing after the 30 seconds.
123
The system arms 30
seconds after the last
entry point (door, trunk or hatch) is closed
The system disarms when you insert the
key and turn it to “on”
SCION
SECURITY
Turns
on (no
flashing) during the
Entry
Delay123
SCION
SECURITY
Lights for 30 sec-
onds (Pre- arming
then starts flashing** (System armed)123
123

Page 11 SCION SECURITY SYSTEM
GLASS BREAKAGE SENSOR INFORMATION
The Scion Security provides protection for your vehicle above and beyond\
entry point
monitoring–it “listens” for the noise made by tapping on, or br\
eaking of glass. Using a
microphone designed specifically for this task, the GLASS BREAKAGE SENSOR is
capable of ignoring other noises, which helps to prevent “false alarm\
s” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the Scion Security was installed in your vehicle, care was taken to\
adjust the
sensitivity level of the GLASS BREAKAGE SENSOR. You may observe how it works
following the procedure listed below.
ARM the system.
1.
Press the lock button on the remote control or lock the doors
with the key.
(Remember, the system will not ARM if any door, the trunk or
hatch is open.)


Wait until the STATUS MONITOR’S LED starts flashing. The
2.
LED will flash 30 seconds after the last door, the trunk or
hatch is closed.
* for some vehicles the LED will turn off instead of flashing after the 30 seconds.

With the tip of a key, tap the center of the driver’s door
3.
window. Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in cold weather, or you may crack or break it.
A WARN AWAY ALARM should be TRIGGERED. If the
ALARM is not TRIGGERED, make sure you performed the
procedure correctly and try again. If you find that the system
did not perform as expected, contact your Scion dealer for
more information.
DISARM the system to stop the WARN AWAY ALARM. Press
4.
the unlock button
SCION
SECURITY

SCION SECURITY SYSTEM Page 12
PROGRAMMING
The Scion Security is factory-set to not PASSIVELY ARM. To change the system’s
operation for PASSIVE ARMING operation, as well as adjust the ENTRY DELAY time,
follow the procedure below. For more information on this feature, please refer to page 7.
(Not applicable to vehicles with Smart Key system. Please consult your \
Scion
Dealer for programming information.)
PA S SIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
DISARM the Security system before proceeding below by using the remote c\
ontrol or
key as described on page 6.
Before you begin:
1.
Open the driver’s door. Close the remaining
doors and the trunk or hatch. Unlock all doors
with the inside lock switch. Remove the key
from the
ignition
switch.
Lock
d. , then unlock
the driver’s door
inside lock button
3 times .
The system locks the door
f.
in 2 seconds; if this does not
happen, start over.
Start the Programming Procedure. (Complete these steps within 40 seconds.)
Lock
b. then unlock the
driver’s door inside lock
button 1 time.The system locks the door
c.
in 2 seconds; if this does
not happen, start over.
Programming is now
complete.
Select the Operating Mode and Complete the Programming Procedure.
3.
Close, then Open the driver’s
a.
door:
2 times = PASSIVE ARMING OFF
3 times = PASSIVE ARMING ON,
0 Sec. ENTRY DELAY
4 times = PASSIVE ARMING ON,
15 Sec. ENTRY DELAY
5 times = PASSIVE ARMING ON,
30 Sec. ENTRY DELAY
Close the
a.
driver’s door. Lock
b. and unlock all doors
3 times by key or remote
control.Open and close
c.
the driver’s
door.
Open the
e.
driver’s door.
Unlock the driver’s
g.
door.
Insert and remove the key from the igni -
2.
tion key cylinder 3 times; this must be
completed within 5 seconds.