sensor VOLKSWAGEN CC 2012 Owner's Manual

The Tire Pressure Monitoring System uses a pressure sensor in each
wheel. Signals from the sensors are transmitted to the TPMS.
The TPMS checks the tire pressure of all 4 tires while you are driving
and warns if there is a loss of pressure while the vehicle is moving.
Pressure loss that is 25% or more of the benchmark value pro-
grammed into the system is signaled by the indicator light (telltale)
described above, by acoustic warnings, and by text messages in the
instrument cluster display.
If you mount tires of a different size than the factory installed tires, an
authorized Volkswagen dealer or an authorized Volkswagen Service
Facility can adjust the benchmark TPMS tire pressure to match the
new tires. Without this adjustment, TPMS may not work correctly or at
all.
The tire pressure recommended for the tires originally installed on the
vehicle is on a sticker on the driver door jamb ⇒  Tire inflation pres-
sure.
Display in the instrument cluster
The display in the instrument cluster shows the vehicle with the actual
and benchmark tire pressures of all 4 road wheels ⇒ fig. 117

Tire pressure display screen
⇒ fig. 117 Meaning
(1) Tire pressure warning, left rear
tire.
(2) Current tire pressure, front left
tire.
(3) Benchmark pressure, front tires
(4) Current tire pressure, front right
tire.
(5) No data received, right rear tire.
(6) Benchmark pressure, rear tires

Spare wheel or compact spare wheel
The spare wheel or compact spare wheel has no tire pressure sen-
sor. When the spare or compact spare wheel is mounted on the vehi-
cle, the Tire Pressure Monitoring System (TPMS) indicator light will
flash in the instrument cluster display. The TPMS continues to moni-
tor the other 3 wheels.
Tire storage
If the tires do not move for an extended period of time, the sensors
will not transmit tire pressures to the system. This saves sensor bat-
tery life. When the ignition is switched on, the sensors transmit sig-
nals to the Tire Pressure Monitoring System.
WARNING
Incorrect tire pressure can cause sudden tire failure, loss of
vehicle control and serious personal injury.
Always check and correct air pressure in all 4 tires, particu-
larly after changing, exchanging, or repairing tires.
After that, always make sure that all 4 tires are inflated to the
correct tire pressure for the tires installed on the vehicle.
See the tire pressure label ⇒  Tire inflation pressure and the
Owner's Literature for recommended cold tire inflation pressure
and other important information.
When replacing tires or wheel rims on vehicles equipped with
TPMS, always read and heed all of the information and WARN-
INGS ⇒  Tires and wheels.
NOTICE
The wheel electronics are attached to special aluminum valves
on the wheels. These valves are screwed on rigidly. Never bend
the valves “into position” when checking and adjusting tire
pressure.
Missing tire air valve caps could result in damage to the
valves, as well as to the sensors on the Tire Pressure Monitoring
System. Therefore, make sure your valve caps conform to the
specifications of those originally installed on the vehicle and
that they are always tightly and properly screwed on to the
valves. Do not use metallic valve caps.

Do not use “comfort valve caps”, as these do not seal proper-
ly and could therefore cause damage to the sensors.
When changing or rotating the tires, be careful not to damage
the valves or sensors.
The aluminum valves that are installed should be replaced
after about 6 years of use because of aging in the rubber seals.
The valves can be replaced when a tire is changed. Do not reuse
aluminum valves after they are removed. They must be replaced.
The tire pressure sensor can be reused.

When a turn signal is set, unnecessary lines and areas are hidden.
Orientation lines overview
Meaning of the orientation lines and areas projected on screen
⇒ fig. 155. All distances of the orientation lines refer to a vehicle on a
level surface.
(1) Red: Safety distance. Area up to about 16 inches (40 cm) behind
the vehicle on the road.
(2) Vehicle's width limits.
(3) Point to change steering angle.
When the yellow line touches the curb or any other parking
space boundary, the steering wheel must be turned in the oppo-
site direction (close-up view).
(4) The area parallel to the vehicle that is needed for parking. The
area shown must fit completely into the parking space.
(5) Parked vehicle at the curb.
Parking
Position the vehicle about 3 feet (1 meter) away from and parallel
to the parking space and shift into Reverse.
On the screen of the navigation system, activate Mode 2 for paral-
lel parking.
Back up slowly and steer the vehicle so that the yellow surface on
the screen is flush with the side boundary of the parking space (such
as the curb) and stops short of any obstacle (5), such as another ve-
hicle.
Turn the steering wheel as far as it will go into the direction of the
parking space and slowly back up.
Once the yellow line (3) touches the side of the parking space, for
example, a marking or the curb (close-up view), turn the steering
wheel as far as it will go in the opposite direction.
Continue backing up until the vehicles is positioned in the parking
space parallel to the road. If necessary, correct the parking position.
It may take up to 5 seconds for the area detected by the sensors
to be displayed on the factory-installed radio or navigation system
screen.

WARNING
Park Distance Control is no substitute for careful and attentive
driving. Never rely completely on these systems for information
about people and objects that might be in the way of the vehicle
and could be struck resulting in serious personal injuries.
The sensors have blind spots in which they cannot detect
people, animals, and objects.
Always be careful and look around you when parking. The
sensors cannot always detect people, animals, and objects.
Watch out for small children and animals in particular.
Certain types of clothing and the surfaces of certain objects
do not reflect the ultrasonic waves that the sensors send and
receive. Such objects and persons wearing such clothing will
not be detected by PDC or will not be detected accurately.
Noise in the area can interfere with the signals of the Park
Distance Control sensors. Under certain circumstances, the
system will not detect people and objects for this reason.
NOTICE
Things like trailer draw bars, thin rods, fences, trees, narrow
painted vertical poles, posts, or a luggage compartment lid that
is opening may not be detected by the Park Distance Control
sensors and could damage the vehicle.
If you continue driving closer to an object that the Park Dis-
tance Control has already detected and reported, the object may
disappear from the sensor range and may no longer be detected.
This is especially true for low or high objects. The system will no
longer sound warnings about these objects. Ignoring signals
from the Park Distance Control system could result in serious
damage to the vehicle.
The sensors in the bumpers can be damaged or become misa-
ligned in low speed impacts and parking maneuvers. Damaged
or misaligned sensors cannot accurately detect or report objects
that might be within range of the PDC system.
To help make sure that the system works properly, always
keep the sensors in the bumpers clean and free of snow and ice;
do not cover the sensors with stickers or other objects.

When cleaning the sensors with power washers or steam
cleaners, only spray the sensors directly for a very short time,
and always keep the washer nozzle at least 4 inches (10 cm)
from the sensors.
Noise from rough roads, cobblestones, other vehicles and the
surrounding area, for example, can prevent the Park Distance
Control system from accurately detecting and reporting people
and objects that may be within range of the sensors.
Aftermarket components such as bicycle racks can impair the
function of the Park Distance Control system.
Volkswagen recommends practicing with the Park Distance Con-
trol system in a location or parking space with no traffic in order to
become familiar with the system and how it works.
Park Distance Control (PDC)

Fig. 156 In the front bumpers: Park Distance Control system sensors.

In order to Operation
view camera dis-
play (if equipped): OR: Tap the function key Z or 26# on the dis-
play.

The indicator light in the button  ⇒ fig. 157 comes on and stays on
as long as the feature is active.
A chime sounds to tell you that the system is on. If the chime does
not sound, PDC is not working. Have the system inspected by an
authorized Volkswagen dealer or an authorized Volkswagen Service
Facility.
Special considerations when using Park Distance Control
In some cases, the Park Distance Control interprets water and ice
on the sensors as an obstacle.
If the distance remains the same, the warning tone volume de-
creases after a few seconds. If a continuous tone sounds, its volume
remains the same.
If the vehicle moves away from the obstacle, the beeping sound
stops automatically. The beep turns on again automatically if the ve-
hicle approaches the obstacle again.
For vehicles with automatic transmissions, there is no beeping
when the transmission is in Park (P) and the electronic parking brake
is engaged.
The volume of the audible signals can be adjusted by an author-
ized Volkswagen dealer or an authorized Volkswagen Service Facili-
ty.
Muting the Park Distance Control volume
You can mute the PDC beeping signals by tapping the  function
key on the Radio or Navigation system screen (if applicable). Tap the
function key again to reactivate the acoustic signals.
Switching Park Distance Control back on after it was switched off re-
activates the volume. System malfunction warning signals cannot be
switched off.
If you manually deactivate the display, PDC remains on and the
sound is reactivated.

WARNING
Never rely completely on the PDC for information about people
and objects that might be in the way of the vehicle and could be
struck by the vehicle causing serious personal injury.
The PDC sensors have blind spots where they cannot detect
people or objects.
Always watch for people, especially small children and ani-
mals, because the sensors may not always be able to detect
them.
If you hear a long beep lasting about 3 seconds when you first
turn PDC on or the indicator light in the button starts blinking, this
means there is a malfunction in the Park Distance Control system.
Switch off the Park Distance Control system with the button and have
it immediately checked by an authorized Volkswagen dealer or an
authorized Volkswagen Service Facility.

NOTICE
To help prevent vehicle damage in a car wash:
Compare the vehicle track width with the dimensions of the
guide rails in the car wash to help prevent damage to wheel rims
and tires!
Switch off the rain sensor before driving the vehicle through a
car wash ⇒  Rain sensor.
Make sure there is enough clearance for the height and width
of the vehicle.
To help prevent paint damage to the engine hood, place wiper
blades against the windshield after they have dried. Do not let
them snap back into place.
Fold the outside mirrors toward the vehicle body. Do not fold
power folding mirrors manually!
Lock the luggage compartment lid to help prevent uninten-
tional opening in the car wash.
Washing with a power washer

WARNING
Improper use of power washers can cause serious invisible
permanent damage leading to tire failure and loss of vehicle
control. This can cause accidents and severe personal injury.
Keep sufficient distance between water jet and tires. Never
wash tires with a nozzle that sprays the water out in a direct
stream regardless of the distance to the tire and even for a very
short time.
Never use “dirt blasters” to clean tires. Even spraying from a
relatively long distance for a very short time can do visible or
invisible damage to tires.
WARNING
After the vehicle has been washed, the wet brakes or, in winter,
brake discs or pads coated with ice, react slower and need
longer stopping distances.
Always dry the brakes and clean off any ice coatings with a
few careful applications of the brake. Make sure not to endan-
ger other motorists or cyclists or disobey legal requirements.
NOTICE
Water temperature should not be more than +140 °F (+60 °C).
To help prevent damage to the paint, do not wash the vehicle
in direct sunlight.
In order for Park Distance Control to work correctly, the sen-
sors in the rear bumper must be kept clean and clear of snow
and ice.
When using a power washer or steam cleaner, only spray the
sensors directly for a short period of time and always keep the
nozzle at least 4 inches (10 cm) from the sensor.
Do not clean icy or snow-covered windows with a power
washer.
When washing or rinsing the vehicle in cold weather, do not
let water get into the lock cylinders or point the hose at gaps
around the doors, hood, or luggage compartment lid. The water