change wheel VOLKSWAGEN CC 2015 Owner´s Manual

If the tire is not “flat” and you do not have to change the tire
or wheel immediately, drive at reduced speed to the nearest
service station to check the tire pressure and add air as re-
quired.
When replacing tires or wheel rims on vehicles equipped with
TPMS, always read and heed the information and all WARN-
INGS in the section ⇒  Tires and wheels.
WARNING
Failure to heed warning lights and instrument cluster text mes-
sages can cause the vehicle to break down in traffic and result
in a collision and serious personal injury.
Never ignore warning lights or text WARNINGS.
Always stop the vehicle as soon as it is safe to do so.
NOTICE
Failure to heed warning lights or text WARNINGS can result in
vehicle damage.
Tire Pressure Monitoring System (TPMS)

Fig. 117 Display screen in the instrument cluster: Current tire pres-
sures in psi.

WARNING
The effectiveness of ESC can be significantly reduced if other
components and systems that affect vehicle dynamics, includ-
ing but not limited to brakes, tires, and other systems men-
tioned above, are not properly maintained or functioning.
Always remember that vehicle alterations or modifications
can affect the functioning of the ABS, BAS, ASR, EDL, and ESC
systems.
Changing the vehicle suspension or using an unapproved
tire/wheel combination can change the way the ABS, BAS, ASR,
EDL, and ESC systems work and reduce their effectiveness.
The effectiveness of ESC is also determined by the tires fitted
⇒  Tires and wheels.
All 4 wheels must be equipped with identical tires in order for
ESC and ASR to work properly. Differences in the tread circumfer-
ence of the tires can cause the system to reduce the engine power
when it is not expected.
If ABS is not working, ESC, ASR, and EDL will also not work.
You may hear noises when these systems are active.
Switching Anti-Slip Regulation (ASR) on and off

Fig. 145 In the center console: Button for switching ASR on and off
manually.

When a turn signal is set, unnecessary lines and areas are hidden.
Orientation lines overview
Meaning of the orientation lines and areas projected on screen
⇒ fig. 155. All distances of the orientation lines refer to a vehicle on a
level surface.
(1) Red: Safety distance. Area up to about 16 inches (40 cm) behind
the vehicle on the road.
(2) Vehicle's width limits.
(3) Point to change steering angle.
When the yellow line touches the curb or any other parking
space boundary, the steering wheel must be turned in the oppo-
site direction (close-up view).
(4) The area parallel to the vehicle that is needed for parking. The
area shown must fit completely into the parking space.
(5) Parked vehicle at the curb.
Parking
Position the vehicle about 3 feet (1 meter) away from and parallel
to the parking space and shift into Reverse.
On the screen of the navigation system, activate Mode 2 for paral-
lel parking.
Back up slowly and steer the vehicle so that the yellow surface on
the screen is flush with the side boundary of the parking space (such
as the curb) and stops short of any obstacle (5), such as another ve-
hicle.
Turn the steering wheel as far as it will go into the direction of the
parking space and slowly back up.
Once the yellow line (3) touches the side of the parking space, for
example, a marking or the curb (close-up view), turn the steering
wheel as far as it will go in the opposite direction.
Continue backing up until the vehicles is positioned in the parking
space parallel to the road. If necessary, correct the parking position.
It may take up to 5 seconds for the area detected by the sensors
to be displayed on the factory-installed radio or navigation system
screen.

WARNING
Using solvents or other improper cleaning products on surfac-
es where airbags are located can change the way airbags de-
ploy in a crash.
Products containing solvents will change the properties of
the plastics and may cause plastic parts to break and fly
around when the airbag deploys in a crash, causing injury.
Never use solvents or cleaners on the steering wheel horn
pad or on the instrument panel because they can damage the
airbag cover or change the stiffness or strength of the material
so that the airbag cannot deploy and protect properly.
When cleaning the horn pad and instrument panel, use only a
soft, dry cloth or a cloth moistened with plain water.
Cleaning the safety belts

WARNING
Items stored between the safety belt buckle and the center con-
sole can cause safety belt buckle to send the wrong infor-
mation to the airbag control unit and prevent the Advanced Air-
bag System from working properly.
Always make sure that nothing can interfere with the safety
belt buckles and that they are not obstructed.
WARNING
Improper care and servicing, and improper modification and
repair work, can increase the risk of personal injury and death
by preventing an airbag from deploying when needed or de-
ploying an airbag unexpectedly:
Never repair, adjust, or change any parts of the airbag sys-
tem.
All work on the airbag system, steering wheel, instrument
panel, front seats or electrical system (including the installation
of audio equipment, mobile telephones and CB radios, etc.)
should be performed by authorized Volkswagen dealers or au-
thorized Volkswagen Service Facilities. They have the neces-
sary manuals, training, and special equipment.
The airbag system can be activated only once. After an air-
bag has inflated, it must be replaced.
Use only original equipment airbags approved by
Volkswagen. Have them installed by a trained technician who
has the necessary tools and diagnostic equipment to properly
replace any airbag in your vehicle and assure system effective-
ness in a crash.
Never permit salvaged or recycled airbags to be installed in
your vehicle.
Undeployed airbag modules and safety belt pretensioners are
classified as Perchlorate Material. Special handling may apply – see
http://www.dtsc.ca.gov/hazardouswaste/perchlorate. Obey all appli-
cable legal requirements regarding handling and disposal of the vehi-
cle or parts of its restraint system, including airbag modules and safe-
ty belts with pretensioners. Authorized Volkswagen dealers and au-

Description Possible causes,
among others Possible remedy
DSG® Direct Shift
Gearbox too hot.
Stop vehicle as soon as
you can safely do so.
Driver seat and
outside mirrors
move when vehi-
cle is unlocked.
Convenience
settings are stored.
Correct convenience
settings
Memory-seat set-
tings are stored.
– Reassign seat setting
– Clear memory-seat
memory
Front seats can-
not be adjusted
with power con-
trols.
Vehicle battery dead. Charge vehicle battery
Fuse blown. Check fuse and replace if
necessary
No jack, spare
wheel, or com-
pact spare wheel
in the vehicle.
Equipment differs
depending on the
vehicle.
No direct corrective action
possible; depends on the
vehicle equipment. Con-
tact an authorized
Volkswagen dealer or an
authorized Volkswagen
Service Facility for assis-
tance.
Vehicle has run-flat
tires (mobility tires).
Features do not
work as de-
scribed in this
manual.
Settings were ad-
justed in the
Volkswagen Infor-
mation System.
Check and reset to factory
settings if necessary
Headlights do not
light up the road
as they should.
– Headlights incor-
rectly adjusted.
– Light bulbs burned
out.
– Low beams not
switched on.
– Have the headlight
range adjusted by an au-
thorized Volkswagen
dealer or an authorized
Volkswagen Service Fa-
cility.
– Change light bulbs
– Switch on low beams

WARNING
Changing a wheel, especially on the side of the road, can be
dangerous. To help reduce the risk of serious personal injury:
Always stop the vehicle as soon as it is safe to do so. Move
the vehicle a safe distance off the road where it is safe to
change the wheel.
Always make sure that all passengers, especially children,
are in a safe place outside the vehicle and away from the vehi-
cle and traffic (such as behind a guard rail).
Turn on the emergency flashers and set up another warning
device about 25 yards (25 meters) behind the vehicle to warn
approaching traffic.
Change a wheel by yourself only if you are familiar with the
necessary steps. Otherwise, get expert assistance.
Always switch the engine off, set the electronic parking
brake, and shift the transmission into Park (P) (automatic
transmission) or any gear (manual only) to help prevent the ve-
hicle from moving suddenly and slipping off the jack.
Always make sure that the ground is level and firm. If neces-
sary, place the jack on a large and sturdy board or on a similar
ground support.
Always block the wheel diagonally opposite the wheel being
changed with chocks or other similar things.
If you are towing a trailer, always unhitch it from your vehicle
before starting to change the wheel. Always apply the trailer
brakes firmly and make sure the trailer cannot move uninten-
tionally.
Always use proper and undamaged tools when changing a
wheel.
Once a wheel is lifted off the ground, having the transmission
in Park (P) or in gear will not prevent sudden vehicle move-
ment.
Always use a jack that has been approved by the manufac-
turer for your vehicle. Never use other jacks, even if they have
been approved for use on other Volkswagen models.
To reduce the risk of losing control, crashes, and serious
personal injuries, never loosen the screws on rims with thread-
ed rim rings.

2. Switch off the engine. Automatic transmission: shift the transmis-
sion into Park (P)) ⇒  Automatic transmission: Selector lever. Man-
ual transmission only: shift into a gear ⇒  Manual transmission:
Gearshift lever. Then set the electronic parking brake ⇒ Braking
and parking to help prevent the vehicle from moving.
3. If towing a trailer: Unhitch the trailer from the vehicle and park the
trailer properly.
4. Straighten the steering wheel so that the front wheels point straight
forward.
5. Block the diagonally opposite wheel with chocks or other suitable
things.
6. Loosen the wheel bolts of the wheel to be changed ⇒  Wheel bolts.
7. Find the jack lift point ⇒ fig. 191 on the vehicle frame that is closest
to the wheel to be changed.
8. Crank up the jack so that it still just fits underneath the lift point.
9. Position the jack so that its base is directly underneath the lift point
⇒ fig. 192, making sure that the entire base of the jack rests se-
curely on the ground.
10. Align the jack and wind up the jack claw at the same time, until
the claw cradles the vertical rib underneath the vehicle ⇒ fig. 192.
11. Continue cranking up the jack until the wheel is just a little off
the ground.

The vehicle may only be lifted by a jack positioned at one of the four
jack lift points ⇒ .
Checklist
For your own safety and that of your passengers, carry out the follow-
ing steps in the order listed ⇒ .
1. Find a level spot on firm ground for lifting the vehicle.
2. Switch off the engine. Automatic transmission: shift the transmis-
sion into Park (P)) ⇒  Automatic transmission: Selector lever. Man-
ual transmission: shift into a gear ⇒  Manual transmission: Gear-
shift lever. Then set the electronic parking brake ⇒  Braking and
parking to help prevent the vehicle from moving.
3. If towing a trailer: Unhitch the trailer from the vehicle and park the
trailer properly.
4. Straighten the steering wheel so that the front wheels point straight
forward.
5. Block the diagonally opposite wheel with chocks or other suitable
things.
6. Loosen the wheel bolts of the wheel to be changed ⇒ Wheel bolts.
7. Find the jack lift point on the vehicle frame that is closest to the
wheel to be changed.
8. Remove the cover panel in the side sill. To do so, pull forcefully but
carefully in the direction of the arrow ⇒ fig. 193. Secure the cover
panel with the retaining strap.
9. Crank up the vehicle jack so that it still just fits underneath the lift
point.
10. Position the jack so that its base is directly underneath the lift
point ⇒ fig. 194, making sure that the entire base of the jack rests
securely on the ground.
11. Align the jack and wind up the jack claw at the same time, until
the claw cradles the vertical rib underneath the vehicle ⇒ fig. 194.
12. Continue raising the vehicle jack until the wheel is lifted off the
ground.

WARNING
Never tow a vehicle without any electrical power.
Never remove the remote control vehicle key from the igni-
tion switch or turn off the ignition with the starter button while
the vehicle is moving. The electronic steering column lock
could suddenly engage, and you would not be able to steer or
control the vehicle. You can lose control of the vehicle, crash,
and seriously injure yourself and others.
If the vehicle loses power while it is being towed, stop towing
the vehicle immediately and contact your authorized
Volkswagen dealer or authorized Volkswagen Service Facility
for assistance.
WARNING
Towing a vehicle changes the way it handles and brakes. To
help reduce the risk of an accident and serious personal injury,
note the following:
The driver of the vehicle that is being towed:
– Since the brake booster also does not work when the en-
gine is stopped, you will need to press harder on the brake
pedal to slow down or stop. Always be alert so as not to rear-
end the towing vehicle.
– Will have to use considerably more force to turn the steer-
ing wheel because the power steering is not working.
The driver of the vehicle that is doing the towing:
– Must accelerate gradually and gently and avoid jerking
movements.
– Must not brake hard or steer sharply.
– Must brake earlier and more gently than in normal driving.
NOTICE
Be careful not to damage the paint when installing and remov-
ing the towing eye and the cover for the threaded hole behind
the bumper.