instrument cluster VOLKSWAGEN CC 2017 Owners Manual

Driver side overview

Fig. 5 Driver side overview.
Key to ⇒ fig. 5:
(1) Instrument cluster:
– Instruments
– Display
– Warning and indicator lights
(2) Headlight switch

Instrument cluster

Upshifting early into the next higher gear saves fuel and reduces
engine noise.
Displays

Fig. 10 In the instrument cluster display: A: Open engine hood, B:
Open luggage compartment lid, C: Open front driver side door, D:
Open rear passenger side door.

Warning and information texts
The status of various vehicle functions and components is monitored
when the ignition is switched on and while driving. Malfunctions are
indicated by red and yellow warning symbols with text messages in
the instrument cluster display (⇒ Warning and indicator lights). In
some cases, they may also be signaled acoustically. The display can
vary depending on the instrument cluster model.

Type of
notification
Symbol
color
Explanation
Priority 1
warning
message
Red Symbol flashing or lit – sometimes with
acoustic warnings.

The trip odometer (trip) shows the distance driven since the last time
the trip odometer was reset. The last digit indicates 1/10 mile
(100 meters).
Outside temperature display
At outside temperatures below about +39 °F (+4 °C), a “snowflake
symbol” (icy road warning) appears in the display. The symbol flashes
at first, then stays on until the outside temperature rises above +43 °F
(+6 °C) ⇒ .
When the vehicle is not moving or when you are driving at very low
speeds, the temperature displayed may be slightly higher than the
actual outside temperature.
The measurement range is from -40 °F (-40 °C) to +122 °F (+50 °C).
Compass display (if applicable)
On vehicles equipped with compass display, the current compass
direction is indicated in the instrument cluster display when the igni-
tion and navigation system are switched on ⇒  Compass.
Selector lever positions
The selector lever position is shown both on the side of the selector
lever and in the instrument cluster display. The respective gear may
also be shown in the instrument cluster display in Drive D and Sport
Drive S, as well as in Tiptronic® mode.
Gear recommendation (manual transmission)
When the vehicle is moving, a fuel economy gear recommendation
may appear in the instrument cluster display ⇒  Shifting.

WARNING
Failure to heed warning lights and instrument cluster text mes-
sages can cause the vehicle to break down in traffic and result
in a collision and serious personal injury.
Never ignore warning lights or text WARNINGS.
Always stop the vehicle as soon as it is safe to do so.
Park the vehicle at a safe distance from moving traffic and
where no part of the hot catalytic converter and exhaust system
can come into contact with flammable materials under the vehi-
cle, such as dry grass, brush, spilled fuel, etc.
A broken down vehicle presents a high accident risk for itself
and others. Switch on emergency flashers and set up a warning
triangle to warn oncoming traffic.
WARNING
Roads and bridges may be dangerously icy even if the outside
air temperature is above freezing.
If you use the outside temperature display to tell you about
frost conditions, remember that roads can even ice over at
temperatures above +39 °F (+4 °C). Always remember: even if
the “snowflake symbol” (icy road warning) is not displayed,
there could still be black ice on the road.
Never rely exclusively on the outside temperature display.
NOTICE
Failure to heed warning lights or text WARNINGS can result in
vehicle damage.
The instrument cluster displays and their arrangement may vary
depending on the vehicle model and engine. For displays without
warning and information messages, malfunctions are only signaled
with indicator lights.
If there are multiple warning messages, the symbols are dis-
played for several seconds in order of importance. The symbols are
displayed until the cause has been corrected.

Calibrating the compass
In order to calibrate the compass, you need a valid compass zone for
the location and enough room to drive in a circle.
Switch on the ignition.
Select the Settings menu followed by the Compass and Calibrate
menu items.
Confirm the Please drive a full circle to calibrate message by
pressing the /+ button on the multi-function steering wheel, and then
drive in a complete circle at about 6 mph (10 km/h).
During calibration, CAL is shown in the instrument cluster display.
The calibration is complete when the compass direction is displayed.
Service reminder display

Radio or Navigation system ⇒ Booklet Radio or
⇒ Booklet Navigation system
Mobile phone package ⇒ Booklet Mobile Phone Package
WARNING
Driving on today's roads demands the full attention of the driv-
er at all times. Driver distraction causes accidents, collisions
and serious personal injury!
Never access menus when the vehicle is moving.
Emergency starting and starting the engine with a very weak ve-
hicle battery or after the vehicle battery has been replaced may
change or delete system settings (including time, date, personal con-
venience settings, and programming). Check the settings and correct
as necessary once the vehicle battery has built up a sufficient charge.
Using the instrument cluster menus

Fig. 13 Right side of the multi-function steering wheel: Controls for
menus in the instrument cluster.

Push the /+ button (⇒ fig. 13) on the right side of the multi-function
steering wheel until a main menu appears in the instrument cluster
display. For a list of main menus, see ⇒  Main menu.
Push buttons # or ∃ to move to another main menu, and push the
arrow up and down buttons * and + to navigate inside the current
main menu. For example, in the Settings main menu, press the ar-
row down button + to navigate to the MFI data submenu.
Displaying a submenu
Press the /+ button ⇒ fig. 13 to display submenu items. For in-
stance, after scrolling to MFI data in the Settings main menu, press
the /+ button to display items available under the MFI data submenu.
Selecting a setting
Some menus are used to select settings for certain features. Push
the /+ button (⇒ fig. 13) to select a setting.
Use the arrow up and down buttons * and + on the multi-function
steering wheel to navigate through the available options.
The selected menu item is located between the 2 horizontal lines.
There may also be a triangle () on the right.
Push the /+ button to select the setting.
Returning to the main menu
Via menu: Use the arrow down button + to select Back and then
press the /+ button ⇒ fig. 13.
For operation with multi-function steering wheel: Press E.
Driver assistance systems button

Fig. 14 In the turn signal and high beam lever: Driver assistance sys-
tems button.

Display Function
Av. consumption
--.- l/100 km
(toggle) is displayed once the vehicle has been
driven about 330 feet (100 m). Until then, dash-
es appear instead of a number. The value dis-
played is updated every 5 seconds.
Range  -- mi Estimated distance in miles (km) that the vehicle
can go with the fuel left in the tank the way you
are currently driving. Takes account of the cur-
rent fuel consumption, among other things. Range  -- km
Route -- mi Distance driven in miles (km) per trip memories
1 and 2 (toggle).
Route -- km
Average speed
-- mph
Average speed on trips per trip memories 1 and
2 (toggle). Displayed once the vehicle has been
driven about 300 feet (100 m). Until then, dash-
es may appear instead of a number. The value
displayed is updated every 5 seconds.
Average speed
-- km/h
-- mph Digital display of the current vehicle speed.
-- km/h
Oil temperature Current engine oil temperature (digital display;
3.6 liter engine only).
Speed warning
--- mph
When the set speed (from 20–155 mph or 30–
250 km/h) is exceeded, an acoustic warning
sounds and a visual message may also appear
in the instrument cluster display. Speed warning
--- km/h

Switching between the displays
Use the arrow up and down buttons (* and +) on the multi-
function steering wheel.