Change VOLKSWAGEN ID.4 2022 Owners Manual

9. Seek expert assistance if necessary.
When the hazard warning lights are switched
on, f
or example if you are being towed, you
can still indicate a change in direction or lane
change by operating the turn signal. The haz-
ard warning lights will be interrupted tempo-
rarily.
Comply with the important information on
towing

Pressing the button again will move the
boot lid back to its starting position.
Signal tones
If the boot lid is opened or closed from the
v
ehicle interior or with the vehicle key,
acoustic signals will sound.
Changing and storing the opening angle
If the area behind or above the vehicle is
smaller than the path of the boot lid, the
opening angle of the boot lid can be changed.

WARNING
The side lights or daytime running lights
are not bright enough to illuminate the
road ahead and to ensure that other road
users are able to see you.
x Always switch the dipped beam head-
lights on if it is dark, raining or visibility
is poor.
x The tail lights will not be switched on
with the daytime running lights. If the
tail lights are not switched on, the v
ehi-
cle may not be visible to other road
users if it is dark, raining, or if visibility is
poor. switches the dipped beam headlights on
and off only when there is a change in the
le

vel of brightness.
x Switch the dipped beam on manually if
required by the weather conditions, e.g.
in the event of fog. When reverse gear is engaged, the
cornering light on both sides of the v

e-
hicle switches on to provide better illumina-
tion of the surrounding area when manoeu-
vring. Switching the rear fog light
on and off
The rear f

og light can only be switched on
when the ignition is switched on

(depending on equipment and not available in
all countries).
Ov
ertaking
If you indicate left (left-hand traffic: indicate
right) to overtake, ACC will accelerate the ve-
hicle and reduce the distance from the vehi-
cle in front. Your set speed will not be excee-
ded.
If ACC does not detect any vehicle in front af-
ter you have changed lane, ACC will acceler-
ate the vehicle up to the set speed.
Overtaking assistance is not available in all
countries.
Stop-and-go traffic
ACC can brake the vehicle to a standstill and
keep it stationary. ACC remains active and
the instrument cluster display shows
ACC ready
to start for a few seconds.
On vehicles with Travel Assist, you can extend
this time by continuing to hold the steering
wheel.
As long as ACC remains active, the vehicle
will move off again automatically as soon as
the vehicle in front moves off (depending on
the vehicle equipment level and not available
in all countries).
Extending or reactivating readiness to drive:

Fig. 107
V ehicle changes lane.
ACC may not react or may react with a delay
or with an unwanted response in the follow-
ing driving situations:

wise cause accidents or injuries. The sys-
tem is not a substitute f
or the full concen-
tration of the driver.
x Adapt your speed and distance from the
vehicles ahead to suit visibility, weather,
road and traffic conditions.
x Your hands should always be on the
steering wheel so that you can steer at
any time.
x Observe the displays in the exterior mir-
ror housings and on the instrument clus-
ter display and act in accordance with
the requests.
x Always pay attention to what is happen-
ing around the vehicle.
x Never use the lane change system if the
radar sensors are dirty, covered or dam-
aged. These circumstances can impair
the proper functioning of the system.
x It may be hard to see the display in the
wing mirror in direct sunlight. The radar sensors calibrate themselves
once in the first f
ew kilometres after
vehicle delivery and if the sensors are re-
paired. The sensor range may be limited dur-
ing the calibration phase. Driving with the lane change
system
Please refer to at the start of the chap-
ter on page 172. Fig. 113
In the e
xterior mirror housing: visual
displays of the lane change system.
Switching on and off
You can switch the lane change system on
and off in the Assist systems menu of the In-
fotainment system. When the lane change
system is switched on, the yellow indicator
lamp in the exterior mirror housing lights
up once briefly.
This most recent system setting is retained
e

ven after the ignition has been switched off
and on.
Function
When switched on, the lane change system is
active from a speed of around 15 km/h
(9 mph). The lane change system is deactiva-
ted at a vehicle speed below 10 km/h
(6 mph).
In the following driving situations, the yellow
indicator lamp lights up in the housing of
the respectiv

e exterior mirror:

The yellow indicator lamp flashes if a pos-
sible critical situation is detected when you
indicate in the direction of the detected v
ehi-
cle.
The faster another vehicle approaches, the
earlier there is a corresponding display in the
exterior mirror.
Lane change system “Side Assist Plus”
If the vehicle is equipped with a lane keeping
system (Lane Assist) and the system is
switched on, the driver is warned by a correc-
tive steering intervention when changing
lanes during a possible critical situation (in-
formation level, warning level). The steering
intervention also occurs when the turn signal
is activated for the corresponding direction. If
the steering intervention is overridden by the
driver, the steering wheel vibrates to give an
additional warning. For this, steering wheel
vibration must be activated in the Assist sys-
tems menu in the Infotainment system.
Automatic deactivation
The lane change system will switch off auto-
matically if the radar sensors are permanent-
ly covered. This can be caused by a layer of
ice or snow in front of the radar sensor, for
example.
A text message will be shown on the instru-
ment cluster display.
If you use the factory-fitted trailer towing
coupling and have set up the necessary elec-
trical connection, the lane change system
switches off automatically. After you have
disconnected the electrical connection, the
lane change system is switched back on au-
tomatically.
If the trailer towing coupling is not factory-
fitted, you must manually switch off the lane
change system and then switch it back on
again.
Brightness
The brightness of the visual display will
change automatically depending on the am-
bient light levels. You can adjust the basic brightness of the
display in the Assist systems menu in the In-
f
otainment system. The lane change system
is not active during the setting procedure. Troubleshooting
Please refer to at the start of the chap-
ter on page 172. Lane change system fault.
The indicator lamp lights up yellow. The yel-
low central warning lamp also lights up.

Data transfer
CybersecurityWhat is cybersecurity?
Cybersecurity comprises measures to reduce
the risk of unauthorised access by malware or
an Internet attack on v
ehicle functions, data
and control units.
What are connectivity components?
Control units for data transmission, interfa-
ces, and media and diagnostic connections
are connectivity components, via which in-
formation and data can be exchanged be-
tween the vehicle and external devices or the
Internet. The connectivity components that
are not included in all vehicles are, in particu-
lar:

the announcement. All other navigation an-
nouncements are giv
en with this volume set-
ting or are muted.
Navigation announcements are not
given if the Infotainment system has
been muted.
Restrictions during navigation
When the Infotainment system cannot re-
ceive any data from GPS satellites, e.g. in
a tunnel or underground car park, navigation
can still continue using the vehicle sensors.
In areas that are not or are not completely in-
cluded in the Infotainment memory, the Info-
tainment system will also try to enable route
guidance.
If navigation data is unavailable or incom-
plete, the navigation system may be unable
to determine the exact vehicle position. As
a result, the navigation may not be as exact
as usual.
Road navigation is subject to continuous
changes, e.g. new roads, road works, road
closures, changes in the road names and
house numbers. In the case of obsolete navi-
gation data, there may be errors or inaccura-
cies during navigation.
Controlling the navigation map
For optimal viewing, you can also operate the
navigation map with advanced finger move-
ments.
Moving the navigation map 239
11A012720AB

Fig. 158
Changing the wiper blade f or the rear
window.
The factory-fitted windscreen wiper blades
are coated with graphite. The graphite coat-
ing ensures that the wiper blade moves qui-
etly over the window. If the graphite coating
is damaged, the wiper will become louder.
Check the condition of the wiper blades on
a regular basis. Rubbing wiper blades should
be changed if damaged or cleaned if dirty