Clock VOLKSWAGEN T-ROC 2021 Owner´s Manual

Fig. 200 Removing the centre wheel trim by turning.
The centre wheel trim protects the wheel bolts and must be fitted again after changing the wheel.
Vehicles with centre wheel trims that can be removed by pulling
⇒ Vehicle toolkit  and insert it into a hole
(alloy wheel) or fit it on the edge (steel wheel) of the trim ⇒ Fig. 199 .
cover in the direction of the arrow.

Vehicles with centre wheel trims that can be removed by turning
-clockwise until it is released from the rim
⇒ Fig. 200 .




WARNING
Using unsuitable hubcaps, or fitting them incorrectly, can cause accidents and serious injuries.
road users.

the airflow to cool the brakes is not restricted or reduced. This also applies if
hubcaps are retrofitted. If the airflow is not sufficient, the braking distance could increase
significantly.
Wheel cover

Fig. 203 Changing a wheel: loosening the wheel bolts.

Fig. 204 Changing a wheel: tyre valve ① and locations of the anti-theft wheel bolt ② or ③.
First read and observe the introductoryinformation and safety warnings⇒Introduction 
Use a suitable box spanner to loosen the wheel bolts.
Slacken the wheel bolts only by approximately one turn before raising the vehicle with the vehicle
jack.
If a wheel bolt is very tight, you may be able to loosen it by pushing down the end of the spanner
carefully with your foot. Hold on to the car for support and take care not to slip.
Loosening the wheel bolts
it will go ⇒ Fig. 203 .
-clockwise ⇒ .
Loosening the anti-theft wheel bolt
-theft wheel bolt out of the vehicle toolkit.
anti-theft wheel bolt as far as it will go.

-clockwise ⇒ .
Screwing in the anti-theft wheel bolt (wheel cover)

-theft wheel bolt using the adapter at position ⇒ Fig. 204②  or ③ and tighten it
slightly in a clockwise direction.
l the other wheel bolts in clockwise direction and tighten them slightly.

⇒ . Do not
tighten the bolts in order but always in diagonally opposite sequence.
⇒ Hubcaps .

WARNING
Incorrect tightening torque or incorrect use of wheel bolts can lead to a loss of control of the vehicle,
and cause accidents and serious injuries.
ep all wheel bolts and threads in the wheel hubs clean and free from oil and grease. The
wheel bolts must be easy to turn and be tightened to the specified torque.
not use
for loosening or tightening them.
After changing a wheel
First read and observe the introductoryinformation and safety warnings⇒Introduction 
luggage compartment ⇒ Vehicle toolkit .

⇒ Tightening torque of wheel
bolts .
as possible.

After changing a wheel, the indicator lamp for the tyre monitoring system may indicate a fault in the
system ⇒ Troubleshooting for Tyre Pressure Loss Indicator .
Breakdown set
Introduction
This chapter contains information on the followingsubjects:
⇒ Contents of the breakdown set 
⇒ Preparations 
⇒ Sealing and inflating tyres 

Remove any items of luggage from the luggage compartment.

Take the breakdown set out of the luggage compartment.

Take the sticker ① from the breakdown set and stick it on the dash panel within the driver's field
of vision.

Do not remove foreign objects (e.g. screws or nails) from the tyre.

WARNING
Ignoring any of the items on this important safety checklist can lead to accidents and severe injuries.

Sealing and inflating tyres
First read and observe the introductoryinformation and safety warnings⇒Introduction 
Sealing a tyre

⇒ Fig. 208⑤  to unscrew the valve core from the tyre valve. Place
the core on a clean surface.
⇒ Fig. 208③  vigorously to and fro several times.
⇒ Fig. 208②  tightly onto the tyre filler bottle in a clockwise direction. The
plastic foil on the closure is pierced automatically.
⇒ Fig. 208②  and place the open end fully on the tyre valve.


⇒ Fig. 208⑤  to screw the valve core back into the tyre valve.
Inflating the tyre
⇒ Fig. 209④  of the air compressor tightly onto the tyre valve.
⇒ Fig. 209②  is closed.

-volt plug ⇒ Fig. 209⑤  into one of the vehicle's 12-volt sockets ⇒ Electrical sockets .