ECU VOLVO S60 2009 Owner´s Manual

Page 41 of 254

01 Safety
ISOFIX lower anchors
01``41 Using the ISOFIX lower child seat
anchors
G015268
ISOFIX lower child restraint anchorsLower anchors for ISOFIX-equipped child
seats are located in the rear, outboard seats,
hidden below the backrest cushions. Symbols
on the seat back upholstery mark the anchor
positions (see the illustration).
To access the anchors:
1. Put the child restraint in position.
2. Kneel on the child restraint to press down
the seat cushion and locate the anchors by
feel.3. Fasten the attachment on the child
restraint's lower straps to the ISOFIX lower
anchors.
4. Firmly tension the lower child seat straps
according to the manufacturer's instruc-
tions.
NOTE

The rear seat's center position is not
equipped with ISOFIX lower anchors.
When installing a child restraint in this
position, attach the restraint's top tether
strap (if it is so equipped) to the top
tether anchorage point (for information
see page 43) and secure the restraint
with the vehicle's center seat belt, see
page 34.

Always follow your child seat manufac-
turer's installation instructions, and use
both ISOFIX lower anchors and top
tethers whenever possible.
G031682
Fasten the attachment correctly to the ISOFIX
lower anchors

Page 42 of 254

01 SafetyISOFIX lower anchors
0142
WARNING

Be sure to fasten the attachment cor-
rectly to the anchor (see the illustration).
If the attachment is not correctly fas-
tened, the child restraint may not be
properly secured in the event of a colli-
sion.

The ISOFIX lower child restraint
anchors are only intended for use with
child seats positioned in the outboard
seating positions. These anchors are
not certified for use with any child
restraint that is positioned in the center
seating position. When securing a child
restraint in the center seating position,
use only the vehicle's center seat belt.

Page 43 of 254

01 Safety
Top tether anchors
0143 Top tether anchors
G031131
Top tether anchorage pointsYour Volvo is equipped with child restraint top
tether anchorages in all rear seat positions.Using the top tether anchorages1. Place the child restraint on the rear seat.
WARNING
Be sure to fasten the child tether attachment
correctly to the anchor. If it is not correctly
fastened, the child seat may not be properly
restrained in the event of a collision.
2. Route the top tether strap under the head
restraint and fasten its attachment to the
anchorage.
G026487
Route the strap under the head restraint3. Firmly tension the top tether strap accord-
ing to the child restraint manufacturer's
instructions. Tension the top tether strap
only after the lower anchor straps or the
seat belt have been firmly tensioned.
See 41 for on securing the child restraint to
ISOFIX lower anchors.
WARNING

Never route a top tether strap over the
top or around the head restraint. It
should always be routed under the head
restraint.

Child restraint anchorages are designed
to withstand only those loads imposed
by correctly fitted child restraints. Under
no circumstances are they to be used
for adult seat belts or harnesses. The
anchorages are not able to withstand
excessive forces on them in the event of
collision if full harness seat belts or adult
seat belts are installed to them. An adult
who uses a belt anchored in a child
restraint anchorage runs a great risk of
suffering severe injuries should a colli-
sion occur.

Do not install rear speakers that require
the removal of the top tether anchors or
interfere with the proper use of the top
tether strap.

Page 80 of 254

02 Instruments and controlsHomeLink® Wireless Control System (option)
0280
Introduction
G030070
The HomeLink Wireless Control System pro-
vides a convenient way to replace up to three
hand-held radio-frequency (RF) transmitters
used to activate devices such as gate opera-
tors, garage door openers, entry door locks,
security systems, even home lighting. Addi-
tional HomeLink information can be found on
the Internet at www.homelink.com.
WARNING

If you use HomeLink to open a garage
door or gate, be sure no one is near the
gate or door while it is in motion.

When programming a garage door
opener, it is advised to park outside of
the garage.

Do not use HomeLink with any garage
door opener that lacks safety stop and
reverse features as required by U.S.
federal safety standards (this includes
any garage door opener model manu-
factured before April 1, 1982). A garage
door that cannot detect an object - sig-
naling the door to stop and reverse -
does not meet current U.S. federal
safety standards. For more information,
contact HomeLink at:
www.homelink.com.
Retain the original transmitter of the RF device
you are programming for use in other vehicles
as well as for future HomeLink programming. It
is also suggested that upon the sale of the
vehicle, the programmed HomeLink buttons be
erased for security purposes. Refer to “Erasing
HomeLink Buttons”.
Programming HomeLink
NOTE
Some vehicles may require the ignition
switch to be turned on or to the second
(“accessories”) position for programming
and/or operation of HomeLink. It is also rec-
ommended that a new battery be placed in
the hand-held transmitter of the device
being programmed to HomeLink for quicker
training and accurate transmission of the
radio-frequency signal.1. Position the end of your hand-held trans-
mitter 1–3 inches (5–14 cm) away from the
HomeLink button you wish to program
while keeping the indicator light in view.
2. Simultaneously press and hold both the
chosen HomeLink and hand-held transmit-
ter buttons until the HomeLink indicator
light changes from a slow to a rapidly blink-
ing light. Now you may release both the
HomeLink and hand-held transmitter but-
tons.

Page 81 of 254

02 Instruments and controls
HomeLink® Wireless Control System (option)
02``81
NOTE
Some devices may require you to replace
this Programming Step 2 with procedures
noted in the “Gate Operator / Canadian Pro-
gramming” section. If the HomeLink indica-
tor light does not change to a rapidly
blinking light after performing these steps,
contact HomeLink at www.homelink.com.3.
Firmlypress, hold for five seconds and
release the programmed HomeLink but-
ton up to two separate times to activate the
door. If the door does not activate, press
and hold the just-trained HomeLink button
and observe the indicator light.
•If the indicator light stays on con-
stantly, programming is complete
and your device should activate when
the HomeLink button is pressed and
released.•If the indicator light blinks rapidly for
two seconds and then turns to a con-
stant light continue with “Program-
ming” steps 4-6 to complete the pro-
gramming of a rolling code equipped
device (most commonly a garage door
opener).
4. At the garage door opener receiver (motor-
head unit) in the garage, locate the “learn”
or “smart” button. This can usually befound where the hanging antenna wire is
attached to the motor-head unit.
5. Firmly press and release the “learn” or
“smart” button. (The name and color of the
button may vary by manufacturer.) There
are 30 seconds to initiate step 6.
6. Return to the vehicle and firmly press, hold
for two seconds and release the pro-
grammed HomeLink button. Repeat the
“press/hold/release” sequence a second
time, and, depending on the brand of the
garage door opener (or other rolling code
equipped device), repeat this sequence a
third time to complete the programming
process.
HomeLink should now activate your rolling
code equipped device.
Gate Operator/Canadian ProgrammingCanadian radio-frequency laws require trans-
mitter signals to “time-out” (or quit) after sev-
eral seconds of transmission – which may not
be long enough for HomeLink to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators are
designed to “time-out” in the same manner.
If you live in Canada or you are having difficul-
ties programming a gate operator or garage
door opener by using the “Programming” pro-cedures,replace “Programming HomeLink”
step 2 with the following:

Continue to press and hold the HomeLink
button while you press and release -
every two seconds (“cycle”) your hand-
held transmitter until the HomeLink indica-
tor light changes from a slow to a rapidly
blinking light. Now you may release both
the HomeLink and hand-held transmitter
buttons.
Proceed with “Programming” step 3 to com-
plete.
Using HomeLinkTo operate, simply press and release the pro-
grammed HomeLink button. Activation will
now occur for the trained device (i.e., garage
door opener, gate operator, security system,
entry door lock, home/office lighting, etc.). For
convenience, the hand-held transmitter of the
device may also be used at any time. In the
event that there are still programming difficul-
ties or questions, contact HomeLink at:
www.homelink.com.

Page 94 of 254

04 InteriorFront seats
0494
Manually adjusted front seats
G027214
1. Front-rear adjustment: lift the bar and
move the seat to the position of your
choice.
2. Raise/lower the front edge of the seat
cushion (option): use the control to pump
the front edge of the cushion up or down.
3. Raise/lower seat height: pump the seat up
or down.
4. Lumbar support: turn the control for firmer
or softer lumbar support.
5. Backrest tilt: turn the control to adjust the
angle of the backrest.6. Control panel for optional power seat (see
page 94 for more information).
WARNING
Do not adjust the seat while driving. The
seat should be adjusted so that the brake
pedal can be depressed fully. In addition,
position the seat as far rearward as comfort
and control allow.
Check that the seat is securely locked into
position after adjusting.Folding the backrests in the front seat
G014805
The front passenger seat backrest can be
folded to a horizontal position to make room for
a long load. Fold the backrest as follows:•
Move the seat as far back as possible.

Adjust the backrest to the upright position.

Lift the catches on the rear of the backrest.

Without releasing the catches, push the
backrest forward.

Move the seat as far forward as possible
so that the head restraint slides under the
glove compartment.WARNING
Cover sharp edges on the load to help pre-
vent injury to occupants. Secure the load to
help prevent shifting during sudden stops.Power seat - (option on certain models)OperationDriver's seat: The seat can be adjusted if the
ignition key is in position I, II or if the engine is
running. It can also be adjusted as follows with
the ignition off:

Page 102 of 254

04 InteriorRear seat and trunk
04102
Folding the rear seat backrest
8503282m
G027327
Backrest release handles in trunkBoth rear seat backrests can be folded down,
together or individually to enable you to trans-
port long objects.
Fold the rear seat backrests as follows:
1. Check first that the head restraint is folded
down.
2. Pull the handle in the cargo compartment
as shown in the illustration.
3. Fold the backrest down.
G028003
WARNING
Keep vehicle doors and the luggage com-
partment locked and keep keys out of a
child's reach. Unsupervised children could
lock themselves in an open trunk and risk
injury. Children should be taught not to play
in vehicles.
On hot days, the temperature in the trunk or
vehicle interior can rise very quickly. Expo-
sure of people to these high temperatures
for even a short period of time can cause
heat-related injury or death. Small children
are particularly at risk.
WARNING

When the backrest is returned to the
upright position, check that it is properly
locked in place. Return the head
restraints to the upright position.

Long loads should always be securely
anchored to help avoid injury in the
event of a sudden stop.

Always turn the engine off and apply the
parking brake when loading/unloading
the vehicle.

Place the transmission in the P position
(automatic transmission) to help pre-
vent inadvertent movement of the gear
selector.

The vehicle features a 60/40 split fold-
down rear seat. This function is per-
formed by handles inside the trunk, and
also provides a means for children and
adults to enter the passenger compart-
ment in the event they become locked
inside the trunk.

Adults are advised to familiarize them-
selves with the operation and location
of the release handles.

To fold down the rear seats from inside
the trunk, pull the release control han-
dles located on either side of the trunk.

Page 103 of 254

04 Interior
Rear seat and trunk
04``103 Carrying long loads (ski hatch)
G028068
The center backrest cushion folds forward,
allowing you to transport long, light cargo such
as skis in the trunk of your vehicle. To lower the
backrest:
1. Pull the right release control handle in the
trunk to release the backrest, see
page 102.
2. From the rear seat, fold down the right sec-
tion of the backrest slightly.
3. Release the flap by pushing the catch
(located on the rear side of the backrest)
upward and pulling the flap forward.
4. Return the backrest to the upright position.The cover on the rear seat armrest does not
have hinges and should be removed before the
ski hatch is used.
To remove:
1. Open the cover approximately 30°.
2. Pull it straight up.
To put in place:
1. Press the cover into the groove behind the
upholstery.
2. Close the cover.
Grocery bag holder (option)
G027223
Open the trunk lid. Hang or secure your grocery
bags§ using the tensioning straps or holders.
Center head restraints
G028074
Adjust the head restraint verticallyThe center head restraint can be adjusted
according to the passenger's height. The
restraint should be carefully adjusted to sup-
port the occupant's head.
The head restraint can be raised by pulling
straight up or lowered by pressing the catch at
the base of the left head restraint support and
pushing down.

Page 105 of 254

04 Interior
Spare wheel, tools and jack
04
*Option/accessory, for more information, see Introduction.
105
G027201
Spare wheel* Securing bracket Tool bag* with towing eyelet Jack*
The spare wheel, jack and tool bag are located
under the floor of the trunk. To access the
spare tire:
1. Pull up the floor mats.
2. Remove the jack and tool bag.
3. Unscrew the spare wheel and lift it out.
WARNING
Make sure that the spare tire, jack and tool
bag are properly secured with the securing
bracket to help keep these components in
place in the event of a sudden stop.If the vehicle is equipped with a grocery bag
holder:
1. Turn the two clips, which are located at the
rear corner of the mat, 90°.
2. Pull the front of the floor mat back towards
the trunk lid opening.
3. Lift the mat slightly and turn 90° to lift it out.
4. Lift the mat out of the trunk.
5. Unscrew the spare tire and lift it out.
6. Return and secure everything in reverse
order.
See page 170 for more information on using
the jack.

Page 140 of 254

06 Starting and drivingTowing
06140
Emergency towing
ABC
G028091
Front towing eyeletThe towing eyelet is located in the tool bag,
under the floor of the trunk, with the spare tire.
This eyelet must be screwed into the positions
provided on the right sides of either the front or
rear bumper (B, see illustrations).
WARNING
Do not use the towing eyelets to pull the
vehicle up onto a flat bed tow truck.
To attach the towing eyelet:A. Use a coin to pry open the lower edge of
the cover (A)
1.
B. Screw the towing eyelet (C) in place, first
by hand and then using the tire iron until it
is securely in place.
After the vehicle has been towed, the eyelet
should be removed and returned to the tool
bag. Press the cover back into position.A
B
C
G028093
Rear towing eyelet
Precautions when the vehicle is in tow•
The steering wheel must be unlocked. Turn
the ignition key to position I or II.

The gear selector must be in position N.

Maximum speed: 50 mph (80 km/h). Do not
exceed the maximum allowable towing
speed.

Maximum distance with front wheels on
ground: 50 miles (80 km).

While the vehicle is being towed, try to
keep the tow rope taut at all times.

The vehicle should only be towed in for-
ward direction.
1The opening in the cover may vary.

Page:   < prev 1-10 11-20 21-30 next >