display VOLVO S60 2009 Owner´s Manual

09 Maintenance and servicing
Replacing bulbs
09``203 Replacing bulbs in the taillight cluster
3501204m
G027277
Location of bulbs
Brake lightParking light (left side)Fog light (one side)Side marker lampTurn signalBack up light
All bulbs in the taillight cluster can be replaced
from inside the trunk.1. Switch off all lights and turn ignition key to
position0.
2. Unlock and fold down the side panel to
access the bulbs.
The bulbs are located in two separate bulb
holders, an upper and a lower. Each bulb
holder has a locking pin.
Replace bulbs in the upper and lower
bulb holders as follows:1. To ease the work: disconnect the cable
from the bulb holder.2. Press the catches together and pull out the
holder.
3. Replace the bulb.
4. Reconnect the cable.
5. Close and secure the side panel.
NOTE
If the message indicating a burned out bulb
remains in the information display after the
bulb has been replaced, consult a trained
and qualified Volvo service technician.

09 Maintenance and servicing
Fuses
09``211 Fuse box on the edge of the dashboard
2224 2321
29272826 25
987
19181716
45632
1314151211
38363733
34353132
20
1
10
30
G032340
Fuses are located inside the access panel on
the edge of the dashboard. There are also a
number of spare fuses.No.
A
1
Power driver's seat (option)
25
2
Power passenger's seat
(option)
25
3
Climate system blower
30
4
Control module - front pas-
senger's door
25
No.
A
5
Control module - driver's door
25
6
Ceiling lighting, upper electri-
cal control module
10
7
Moon roof (option)
15
8
Ignition switch, SRS system,
engine control module, immo-
bilizer)
7,5
No.
A
9
Onboard diagnostics, head-
light switch, steering wheel
angle sensor, steering wheel
control module
5
10
Audio system
20
11
Audio system amplifier (option)
30
12
Navigation system display
(option)
10
13 –
38
–

10 Audio
Audio system HU-650 - overview
10
217
HU-650COMPACT
DIGITAL AUDIO
1
789
101112
2
6
5
3
416
17 18 13 14 15
G025598
RND CD random playAM AM (select AM1 or AM2)CD slotDisplayScan (automatically search for radio sta-
tions)CD ejectFM FM (select FM1, FM2, FM3)CD CD playerAUTO AUTO - automatically search for
radio stations
Navigation buttons (seek/change radio
station or CD track)EXIT Exit (exit the menu)Buttons for selecting stored radio stations/
discs in optional CD changerPOWER On/off - press Volume - turnBASS Bass (press to release control and
turn to adjust)TREBLE Treble (press to release control
and turn to adjust)BALANCE Balance (left/right) - press to
release control and turn to adjustFADER Fader (front/rear) - press to release
control and turn to adjustSOURCE PUSH MENU Source/Menu
Press to open main menu Turn to select
FM, AM, CD, CD changer (option), or AUX
(option)

10 AudioAudio system HU-850 - overview
10218
HU-850COMPACT
DIGITAL AUDIO
91011
121314
8 7
16
17 18
15 20 2119 12 65 34
G025599
RND CD random playAM AM (select AM1 or AM2)CD slotDisplay3-CH 3-channel stereoOFF 2-channel stereoDolby Surround Pro Logic IICD ejectFM FM (select FM1, FM2, FM3)CD CD player
AUTO AUTO - automatically search for
radio stationsNavigation buttons (seek/change radio
station or CD track)EXIT Exit (exit the menu)SCAN Scan function (automatically search
for radio stations)POWER On/off - press Volume - turn1-6 Buttons for selecting stored radio sta-
tions/discs in optional CD changerBASS Bass (press to release control and
turn to adjust)TREBLE Treble (press to release control
and turn to adjust)BALANCE Balance (left/right) - press to
release control and turn to adjustFADER Fader (front/rear) - press to release
control and turn to adjustSOURCE PUSH MENU Source/Menu
Press to open main menu Turn to select
FM, AM, CD, CD changer (option), or AUX
(option)

10 Audio
Radio functions HU-650/HU-850
10``221 Selecting a sound source
The sound source (e.g. AM,
FM, etc.) can be selected in two
ways:
•
Use the sound source buttons (see the
center illustration above).
•
Turn the SOURCE knob (see illustration) to
select a sound source (AM1, AM2, FM1,
FM2, FM3, or CD). Press the knob to select
theAM or FMband of your choice.
The sound source selected will be shown in the
display.
Scan
Press the SCAN button to start
the station scan function. When
a station is found, scanning
stops for approximately 10 sec-
onds, after which scanning will
continue.
Press the SCAN or SOURCE button when a
station has been found if you would like to lis-
ten to that station and to discontinue the scan
function.
Station seek up/downPress
or
to start the seek func-
tion. The radio seeks the next audible station
and tunes it in. Repeat the procedure to con-
tinue the seek function.
Manual station searchPress
or
and hold it down.
MAN will be shown in the display. The radio
scans slowly in the selected direction and will
increase the scanning speed after a few sec-
onds. Release the button when the desired
frequency appears in the display.
The frequency can be fine-tuned by short
presses on the or
keys.
The system will remain in manual search mode
for 5 seconds after the button is released, after
which it will return to seek mode.
Steering wheel key pad (option)
G027901
If the vehicle is equipped with the key pad in
the steering wheel press the right or left arrow
to switch between preset stations.

10 AudioRadio functions HU-650/HU-850
10222
Storing stations
G027191
To store a selected station under one of the
station setting buttons 1-6:
1. Tune to the desired station.
2. Press the button under which the station is
to be stored and keep it depressed. The
audio system sound will be interrupted for
a few seconds and
STORED
will appear in
the display. The station is now stored.
A total of 30 stations can be stored; 6 stations
each in AM1, AM2, FM1, FM2, andFM3.
Storing stations automatically
This function automatically
searches for and stores up to
10 strong AM or FM stations in
a separate memory. If more
than ten stations are found, the
ten strongest ones are stored.
This function is especially useful in areas in
which you are not familiar with radio stations or
their frequencies.
To use the AUTO function:
1.
Select radio mode using the AM or FM
buttons, or by turning the SOURCE knob.
2.
Start the search by pressing AUTO for
more than 2 seconds.
3.
AUTO
appears in the display and a number
of stations with strong signals (max. 10)
from the selected frequency band will be
stored in the auto-store memory. If there
are no stations with sufficient signal
strength,
NO STATION
is displayed.
4.
Press the AUTO button or the arrow keys
on the optional steering wheel controls
briefly to select the stored stations.
When the radio is in auto-store mode,
AUTO
is
shown in the display.
AUTO
disappears when
you return to the normal radio mode.Return to the normal radio mode by pressing
theAM, FM, or EXIT button.
To return to the Auto-store mode, press the
AUTO button briefly.

10 Audio
RBDS functions HU-650/HU-850
10``223 Radio Broadcast Data System - RBDS
This feature, which may not be available in your
area, functions only with FM broadcasts. The
radio in your vehicle is equipped with an
advanced system allowing information from
broadcasters to be transmitted visually, as
text, together with the audio signal. This infor-
mation is then decoded by the radio and made
available for several new and unique features.
The RBDS or Radio Broadcast Data System
operates in the FM band only, and the infor-
mation transmitted is supplied exclusively by
participating broadcasters. Volvo has no con-
trol over the accuracy of the data or informa-
tion.
Coverage by local broadcasters may be limited
at this time, but as the technology and benefits
grow, you will find the radio in your vehicle is
equipped to take advantage of this system.PI (Program Information) Seek:When an FM station has been stored as a pre-
set, the radio also stores RBDS program infor-
mation if it is available. When the preset is
selected at a later time, the radio tries to access
updated program information. In weak signal
areas, there may be a delay before the station
becomes audible. During this delay, "PI seek"
will be displayed and there will be no sound.
PI seek can be interrupted by pressing EXIT.
Radio textCertain RBDS stations broadcast program
information, which can be shown in the display.
The text will be shown twice in the display.To start this function:Press the FM button for several seconds.To deactivate this function:Press FM briefly.
Station information will be shown twice in the
display.AlarmAlarms bulletins are transmitted automatically
by certain RBDS stations. The function cannot
be deactivated.Alarm!
is shown in the radio display when an
alarm message is sent. The function is used to
warn motorists of serious accidents, etc.
Program type/station format -PTYThe PTY function allows you to find stations
whose programs suit your taste. Use the PTY
function to select among the different station
formats shown in the list.
To select a station format:
1.
Select radio mode using the FM button, or
by turning the SOURCE knob.2.
Turn the SOURCE knob, select
PTY
and
pressSOURCE.
3.
Turn the SOURCE knob, select a station
format from the list and press SOURCE to
confirm the selected station format. The
PTY
(station format) of the selected station
is now shown in the display.NOTE
Not all RBDS radio stations have PTY des-
ignations.Station formatsFormat
Display text
Off
PTY OFF
News
NEWS
Current affairs
AFFAIRS
Information
INFO
Sports
SPORT
Education
EDUCATION
Drama
DRAMA
Art and culture
CULTURE
Science
SCIENCE

10 AudioRBDS functions HU-650/HU-850
10224
Format
Display text
Entertainment
VARIED
Pop music
POP M
Rock music
ROCK M
Easy listening
EASY M
Light classics
LIGHT M
Classical music
CLASSICS
Other music
OTHER M
Weather
WEATHER
Finance
FINANCE
Religious programs
RELIGION
Travel
TRAVEL
Leisure
LEISURE
Jazz music
JAZZ
Country music
COUNTRY
National music
NATION M
Oldies
"OLDIES"
Format
Display text
Folk music
FOLK M
Documentary
DOCUMENT
Automatic Frequency update (AF)The AF function tunes to the strongest trans-
mitter for the current station, if that station
supports alternative frequencies. AF is
OFF
by
default.
To deactivate AF:
1.
Select radio mode using the FM button, or
by turning the SOURCE knob.
2.
PressSOURCE.
3.
Turn the SOURCE knob, select
ADVANCED MENU and press SOURCE.
4.
Turn the SOURCE knob, select RADIO
SETTINGS and press SOURCE.
5.
Turn the SOURCE knob, select
AF ON/
OFF
(flashing text) and press SOURCE.
6.
PressEXIT.
To reactivate the function, follow the procedure
above and select AF ON in step 5.
Resetting RBDS functionsRBDS functions can be returned to their factory
settings as follows:1. Select radio mode using the FM button, or
by turning the SOURCE knob.
2.
PressSOURCE.
3.
Turn the SOURCE knob, select
ADVANCED MENU
and press SOURCE.
4.
Turn the SOURCE knob, select
RESET TO
DEFAULT
and press SOURCE.
5.
PressEXIT.
ASC - speed compensated volumeThe audio system's volume is adjusted auto-
matically according to the speed of the vehicle.
There are three settings available: low,
medium, or high.
To activate ASC:
1.
Select radio mode using the FMbutton, or
by turning the SOURCE knob.
2.
PressSOURCE.
3.
Turn the SOURCE knob, select
ADVANCED MENU
and press SOURCE.
4.
Turn the SOURCE knob, select
AUDIO
SETTINGS
and press SOURCE.
5.
Turn the SOURCE knob, select
ASC
LEVEL
(flashing text) and press SOURCE.

10 AudioHU-650 - CD player
10226
Starting the CD playerPlease refer to the illustration on page 217 for
the location of the buttons referred to on this
page.
1. Insert a disc into the player.
2.
Press the CD button or turn the SOURCE
knob to CD.Changing tracksBriefly press the
or
keys (or the
corresponding keys on the steering wheel key-
pad) to skip to the previous or next track. The
track number is shown in the display.
Fast forward/backPress and hold down the
or
keys
to search within a track or the entire disc. The
search continues for as long as the buttons are
held in.
NOTE
The corresponding keys on the steering
wheel keypad cannot be used for fast for-
ward/back.Random playThis function plays the tracks on a CD in ran-
dom order (shuffle).1.
Select CD mode and press the RND but-
ton.
RND
is shown in the display as long
as the function is activated.
2.
PressRND again to stop random play.
ScanThis function plays the first 10 seconds of each
track on the CD.
1.
PressSCAN to start the function.
2.
PressSCAN again or EXIT to stop the scan
function and listen to an entire track.CD ejectPress the button (no. 6 in the illustration on
page 218) to eject the disc.
NOTE
•
For reasons of traffic safety, the ejected
CD must be removed within 12 seconds
or it will be automatically drawn back
into the slot and the CD player will
resume playing the most recently
selected track.
•
See page 216 for information on caring
for compact discs.

10 Audio
HU-850 - internal CD changer
10
227
Starting the CD changerThe HU-850 is equipped with an internal, 6-
disc CD changer.
Please refer to the illustration on page 218 for
the location of the buttons referred to on this
page.To load discs into the changer:1.
Press the CD button or turn the SOURCE
knob to CD.
2. Select an empty position by pressing one
of the preset buttons. The display shows
which positions are empty.
LOAD DISC
must be displayed before a disc is inserted
into the player.
3. Insert a disc.
If there are discs in the player when CD mode
is selected, the changer will resume playing the
disc and track that were most recently played.
Selecting a disc position (number)Use the station setting buttons 1-6 to select the
disc to be played. The number of the disc and
the track being played are shown in the display.Changing tracksBriefly press the
or
keys (or the
corresponding keys on the steering wheel key-
pad) to skip to the previous or next track. The
track number is shown in the display.
Fast forward/backPress and hold down the
or
keys
to search within a track or the entire disc. The
search continues for as long as the buttons are
held in.
The corresponding keys on the steering wheel
keypad cannot be used for fast forward/back.
Random playThis function plays the tracks on a CD in ran-
dom order (shuffle).•
SelectCD mode and press the RND but-
ton.
RND
is shown in the display as long
as the function is activated. Random tracks
from randomly selected discs will be
played.
•
PressRND again to stop random play.
ScanThis function plays the first 10 seconds of each
track on the CD.
1.
PressSCAN to start the function.
2.
PressSCAN again or EXIT to stop the scan
function and listen to an entire track.
Scan only works on the selected disc.CD ejectThis function makes it possible to eject a single
disc, or to eject all of the discs in the changer.
•
Press the eject button briefly to eject the
disc that is currently playing.
•
A longer press (more than 2 seconds)
starts the process of ejecting all of the
discs in the changer.NOTE
The
EJECT ALL
function can only be used
while the vehicle is at a standstill and will be
cancelled if the vehicle begins to move.
For reasons of traffic safety, you have
12 seconds in which to remove the ejected
disc. After that, the disc automatically rein-
serts into the player, and the CD player will
resume playing the most recently selected
track.
See page 216 for information on caring for
compact discs.