remote control VOLVO V60 2011 Owner's Manual

02 Locks and alarm
Child safety locks
02
66* Option/accessory, for more information, see Introduction.
Manual blocking of the rear doors
The child safety locks prevent children from
opening a rear door from the inside.
The child safety locks are located on the trailing
edge of the rear doors and are only accessible
when the doors are open.
To activate/deactivate the child safety locks:

Use the remote control key's detachable
key blade to turn the knob, see page 52.
The door is blocked against opening from
the inside.
The door can be opened from both the
outside and the inside.
WARNING
Each rear door has two knob controls - do
not mix up the child safety lock with the
mechanical door lock.
NOTE
•A door's knob control only blocks that
particular door - not both rear doors
simultaneously.
•Cars with an electric child safety lock do
not have a manual child lock.
Electrical locking of the rear doors*
and power windows
Control panel driver's door.
When the electric child safety lock is active
then the rear:
•windows can only be opened with the driv-
er's door control panel
•doors cannot be opened from inside.
The child safety locks are activated/deacti-
vated in all key positions (see page 81 and up
to 2 minutes after the remote control key has
been removed from the ignition switch. If a
door is opened within this time, the function is
deactivated.

Press the button in the driver's door control
panel.
> The information display shows the mes-
sage
Rear child locks Activated and
the button's lamp illuminates when the
locks are active.
ProCarManuals.com

02 Locks and alarm
Alarm*
02

* Option/accessory, for more information, see Introduction.67 General
Activated alarm is triggered if:
•a door, the bonnet or the tailgate is opened
•a movement is detected in the passenger
compartment (if fitted with a movement
detector*)
•the car is raised or towed away (if fitted
with a tilt detector*)
•the battery's cable is disconnected
•the siren is disconnected.
If there is a fault in the alarm system, the infor-
mation display shows a message. In which
case, contact a workshop - an authorised
Volvo workshop is recommended.
NOTE
The movement sensors trigger an alarm in
the event of movement in the passenger
compartment - air currents are also regis-
tered. For this reason the alarm is triggered
if the car is left with a window or the sunroof
open or if the passenger compartment
heater is used.
To avoid this: Close the window/sunroof
when leaving the car. If the car's integrated
passenger compartment heater (or a porta-
ble electric heater) shall be used - direct the
airflow from the air vents so that they are not
pointing upwards in the passenger com-
partment.
NOTE
Do not attempt to repair or modify alarm
system components. All such attempts
could affect the terms of insurance.
Alarm indicator
Same LED as lock indicator, see page 49.
A red LED on the instrument panel indicates
the alarm system's status:
•LED not lit – Alarm not armed
•The LED flashes once every other second
– Alarm is armed
•The LED flashes rapidly after disarming the
alarm (and until the remote control key is
inserted in the ignition switch and key posi-
tion I is selected) – Alarm has been trig-
gered.
Arming the alarm
Press the remote control key lock button.
Disarming the alarm
Press the remote control key unlock but-
ton.
Deactivating a triggered alarm
Press the remote control key unlock button
or insert the remote control key in the igni-
tion switch.
Other alarm functions
Automatic re-arming of the alarmThis function prevents the car being left with
alarm disarmed unintentionally.
If the car is unlocked with the remote control
key (and the alarm is disarmed) but none of the
doors or the tailgate is opened within
2 minutes, then the alarm is automatically re-
armed. The car is relocked at the same time.
Alarm signalsWhen the alarm is triggered, the following hap-
pens:
•A siren sounds for 30 seconds or until the
alarm is switched off. The siren has its own
ProCarManuals.com

02 Locks and alarm
Alarm*
02
68* Option/accessory, for more information, see Introduction.
battery which works independently of the
car battery.
•The direction indicators flash for 5 minutes
or until the alarm is switched off.
Remote control key not workingIf the alarm cannot be switched off with the
remote control key, e.g. if the key's battery is
discharged, the car can be disarmed and the
engine started as follows:
1. Open the driver's door with the key blade.
> The alarm is triggered, the alarm indica-
tor flashes rapidly and the siren sounds.
2. Insert the remote control key in the ignition
switch.
> The alarm is deactivated and the alarm
indicator goes out.
3. Start the engine.
Reduced alarm level
To avoid accidental triggering of the alarm -
e.g. if a dog is left in the car or during transport
on a car train or a car ferry - the movement and
tilt sensors can be temporarily deactivated.
The procedure is the same as with the tempo-
rary disengaging of deadlocks, see page 64.
Testing the alarm system
Testing the movement detector in the
passenger compartment
1. Close all windows. Remain in the car.
2. Arm the alarm, see page 67.
3. Wait 15 seconds.
4. Trigger the alarm by moving your arms for-
ward and back at backrest height.
> A siren sounds and all direction indica-
tors flash.
5. Deactivate the alarm by unlocking the car
with the remote control key.
Testing the alarm sensors in the doors1. Arm the alarm, see page 67.
2. Wait 15 seconds.
3. Unlock the driver's door using the key
blade.
4. Open the driver's door.
> A siren sounds and all direction indica-
tors flash.
5. Deactivate the alarm by unlocking the car
with the remote control key.
Testing the alarm sensors for the bonnet1. Sit in the car and deactivate the movement
sensor, see the previous section Reduced
alarm level.
2. Arm the alarm, see page 67. Remain in the
car and lock the doors with the button on
the remote control key.
3. Wait 15 seconds.
4. Open the bonnet with the handle under the
dashboard.
> A siren sounds and all direction indica-
tors flash.
5. Deactivate the alarm by unlocking the car
with the remote control key.
ProCarManuals.com

03 Your driving environment
Key positions
03

* Option/accessory, for more information, see Introduction.81 Insert and remove the remote control
key
Ignition switch with inserted remote control key.
NOTE
For cars with keyless function*, see
page 57.
Insert the keyHold the end of the remote control key with the
detachable key blade and insert the key in the
ignition switch. Then press the key in the lock
up to its end position.
IMPORTANT
Foreign objects in the ignition switch may
jeopardise the function or destroy the lock.
Do not press the remote control key incor-
rectly turned - Hold the end with the detach-
able key blade, see page 52.
Withdraw the keyPush the remote control key, allow it to eject,
then pull it out.
Functions
The remote control key's 3 different key posi-
tions can be reached without the need to start
the engine. The table shows the functions
available in each key position.
NOTE
To reach key position I or II without starting
the engine - do not depress the brake/
clutch pedal when the following operations
are carried out.
Key position 0Insert the remote control key in the ignition
switch and push it in to the end position.
Key position IWith the remote control key fully inserted into
the ignition switch - Briefly press START/
STOP ENGINE.
Key position IIWith the remote control key fully inserted into
the ignition switch - Press START/STOP
ENGINE for about 2 seconds.
Back to key position 0To return to key position 0 from position I or II
- Briefly press on START/STOP ENGINE.
ProCarManuals.com

03 Your driving environment
Key positions
03
82* Option/accessory, for more information, see Introduction.
Posi-
tionFunction
0Odometer, clock and tempera-
ture gauge are illuminated. The
steering lock is deactivated. The
audio system can be used.
ISunroof*, power windows, 12 V
socket in the passenger compart-
ment, RTI*, phone*, ventilation
fan, ECC and windscreen wipers
can be used.
IIThe headlamps come on. Warn-
ing/indicator lamps illuminate for
5 seconds. All equipment oper-
ates apart from heated seats and
rear window defroster, which only
work when the engine is running.
For information on the audio system's func-
tions with remote control key removed, see
page 216.
Starting and stopping the engineFor information about starting/switching off the
engine, see page 113.
TowingFor important information about the remote
control key during towing, see page 284.
ProCarManuals.com

03 Your driving environment
Seats
03
84* Option/accessory, for more information, see Introduction.
Power seat*
Front edge of seat cushion up/down
Seat forward/backward and up/down
Backrest rake
The power front seats have overload protection
which is tripped if a seat is blocked by an
object. If this happens, go to key position I or
0 and wait a short time before adjusting the
seat again.
Only one movement (forward/back/up/down)
can be made at a time.
PreparationsThe seats can be adjusted for a certain time
after unlocking the door with the remote con-trol key without the key in the ignition switch.
Seat adjustment is normally made in key posi-
tion I and can always be made when the engine
is running.
Seat with memory function*
Store settingMemory button
Memory button
Memory button
Button for storing settings
1. Adjust the seat and the door mirrors.2. Hold the button depressed to store set-
tings while depressing one of the memory
buttons.
Using a stored settingHold one of the memory buttons depressed
until the seat and the door mirrors stop. If you
release the button then the movement of the
seat will stop.
Key memory* in remote control key2
The positions of the driver's seat and the door
mirrors3 are stored in the key memory when the
car is locked with the remote control key.
When the car is unlocked with the same remote
control key it was locked with and the driver's
2For key memory for keyless drive, see page 59.3Only if the car is equipped with power seat and retractable power door mirrors.
ProCarManuals.com

03 Your driving environment
Seats
03

85
door is opened, the driver's seat and also the
door mirrors automatically adopt the positions
stored in the key memory.
NOTE
The seat and the door mirrors do not move
if they are already set the relevant position.
It is also possible to use the key memory by
pressing the unlock button on the remote con-
trol key when the driver's door is open.
The key memory can be activated/deactivated
in the menu system MY CAR under Settings
Car settingsCar key memory
Position of door mirrors and driver's seat in
key. For a description of the menu system, see
page 142.
NOTE
The key memory in the two remote control
keys and the seat's three memories are
completely independent of each other.
Emergency stopIf the seat accidentally begins to move, press
one of the buttons to stop the seat.
Restarting to reach the seat position stored in
the key memory is performed by pressing theunlock button on the remote control key. The
driver's door must then be open.
WARNING
Risk of crushing! Make sure that children do
not play with the controls. Check that there
are no objects in front of, behind or under
the seat during adjustment. Ensure that
none of the backseat passengers will be
trapped.
Heated seatsFor heated seats, see page 153.
Rear seats
Head restraint, centre seat, rear
Adjust the head restraint according to passen-
ger height so that the whole of the back of the
head is covered if possible. Slide it up as
required.
To lower the head restraint again, the button
(located in the centre between the backrest
and head restraint, see illustration) must be
pressed in while the head restraint is pressed
down.
Manual lowering of the outer head
restraints, rear seat
Pull the locking handle closest to the head
restraint to fold the head restraint forward.
The head restraint is moved back manually
until a "click" can be heard.
ProCarManuals.com

03 Your driving environment
Seats
03
* Option/accessory, for more information, see Introduction.87
Electrical lowering of the rear seat's
outer head restraints*
1. The remote control key must be in position
I or II.
2. Press the button to lower the rear outer
head restraints to improve rearward visi-
bility.
WARNING
Do not lower the outer head restraints if
there are any passengers using of the outer
seats.
Move the head restraint back manually until a
click is heard.
WARNING
The head restraints must be in locked posi-
tion after being raised.
ProCarManuals.com

03 Your driving environment
Lighting
03

* Option/accessory, for more information, see Introduction.89 Light switches
Overview, light switches.
Thumbwheel for adjusting display and
instrument lighting
Rear fog lamp
Light switches
Thumbwheel1 for headlamp levelling
Instrument lightingDifferent display and instrument lighting is
switched on depending on key position, see
page 81.
The display lighting is automatically subdued
in darkness - the sensitivity is set with the
thumbwheel.The intensity of the instrument lighting is
adjusted with the thumbwheel.
Headlamp levellingThe load in the car changes the vertical align-
ment of the headlamp beam, which could daz-
zle oncoming motorists. Avoid this by adjusting
the height of the beam. Lower the beam if the
car is heavily laden.
1. Allow the engine to run or have the remote
control key in position I.
2. Roll the thumbwheel up/down to raise/
lower beam alignment.
Cars with Xenon headlamps* have automatic
headlamp levelling and therefore do not have
the thumbwheel.
Main/dipped beam
Headlamp control and stalk switch.
Position for main beam flash
Position for main beam
1Not available for cars equipped with Xenon headlamps*.
ProCarManuals.com

03 Your driving environment
Lighting
03
90* Option/accessory, for more information, see Introduction.
Posi-
tionSpecification
AutomaticA/deactivated dipped
beam. Only main beam flash.
Position/parking lamps
Dipped beam. Main beam and
main beam flash work in this
position.
AApplies to certain markets.
NOTE
Main beam can only be activated in position
.
Main beam flashMove the stalk switch gently towards the steer-
ing wheel to the position for main beam flash.
Main beam comes on until the stalk switch is
released.
Dipped beamWhen the engine is started, dipped beam is
activated automatically2 if the headlamp con-
trol is in position
. If necessary, auto-
matic dipped beam for this position can bedeactivated by a workshop. Volvo recom-
mends that you contact an authorised Volvo
workshop.
In position
dipped beam is always acti-
vated automatically when the engine is running
or when the remote control key is in position
II.
Main beamMain beam can only be activated when the
headlamp control is in position
. Acti-
vate/deactivate main beam by moving the stalk
switch towards the steering wheel to the end
position and release. Alternatively, the main
beam can be deactivated by a light press of the
stalk switch toward the steering wheel.
When main beam has been activated the sym-
bol
illuminates in the combined instru-
ment panel.
Active Xenon headlamps - ABL*
Headlamp pattern with function deactivated (left)
and activated (right) respectively.
If the car is equipped with active Xenon head-
lamps (Active Bending Lights - ABL) the light
from the headlamps follows the steering wheel
movement in order to provide maximum light-
ing in bends and junctions and so provide
increased safety.
The function is activated automatically when
the car is started. In the event of a fault in the
function the
symbol illuminates in the
combined instrument panel at the same time
as the information display shows an explana-
tory text and a further illuminated symbol.
2Applies to certain markets.
ProCarManuals.com