engine VOLVO XC70 2006 Owner´s Manual
Page 177 of 211
169
Engine specifications
Designation: Volvo B 5254 T4
Output 300 hp at 5500 rpm*
(220 kW/92 rps)*
7
8
*3F
%3F2
F*F2 NN
,/22 $-% 3F 1NN
F
< -
*.I,&-1
) -
0.I,3-
*1
'
*
F
5
&
F#%
*2
N(
#-22
0222
**24
%22
NN(
#*F&
%&F2
0222-F2
-* %22
Designation: Volvo B 5254 T2
Output 208 hp at 5000 rpm
(154 kW/83 rps)
7
8
*-0
%F22 /F22
,-*2 $*F .F 1
F
< -
*.I,&-1
) -
0.I,3-
*1
'
*
F
5
3
2#%
*2
Designation: Volvo B 5244 S
Output 165 hp at 6000 rpm
(123 kW/100 rps)
7
8
%00
/F22
,**F$.F 1
F
< -
*.I,&-1
) -
F/I,321
'
*
/
5
%2
-#%
*2
Charge air cooler
(Intercooler)
(
,
1
Page 178 of 211
170
Oil/fluid specifications and volumes
(
!
2
"
(
#
Engine oil
#H G)(5
B@ -
(9)G(5H((%$<%
6#F
& ,F
F 1
67
7(J #%
-=) ,%
* 1
Manual transmission oil
#7@3.-23
7F0, 1#*
*=)
,*
% 1
700,0 1#*
%=)
,*
2 1
Automatic Transmission Fluid
#E4)--23
(4F#.
0=) ,.
* 1
@ &2)5,6.2"1#.
/=) ,.
2 1
'8
Cooling system
(9
%3/O@,32O51
6
$
A
Power steering fluid
Volvo synthetic power steering fluid (Pentosin CHF 11S) P/N 1161529
or equivalent.
D
2
3F=) ,2
3 1
Brake fluid
'+/MZF-0O@,*&2O519$3/-./--
D
2
0/=) ,2
0 1
Climate control system - refrigerant (R 134a)
+#9(B
D
*
* ,%2221"%-/
Fuel
7
(!&.,"+3%1
) $&
@ %&
F=)
,.2 1
( %&=)
,0& 1
Washer fluid reservoir
D
0
&=) ,0
/ 1/
&=) ,/
F 1
6.2"
Page 179 of 211
171
Fuel system, Electronic ignition system, Suspension
Fuel system
>
Distributor ignition system
@ # % * / F -
H #
>
)
# 5
"5&99&,
1
)
# 2
2*& 2
2-*I ,2
. 2
& 1
# %&
/
,*F1
WARNING!
)
>
(
#
•Replacing ignition components e.g. plugs, coil, etc.
•Do not touch any part of the ignition system while the engine is
running. This may result in a shock and bodily injury.
Front suspension
)
9
)
Rear suspension
(
!
2
"
(
#
Page 201 of 211
193 5
During programming, your hand-held transmitter may automatically stop
transmitting. To successfully train HomeLink®, continue to hold the
HomeLink® button. At the same time, repeatedly press and hold your
hand-held transmitter’s button at two-second intervals until HomeLink®
has learned your transmitter’s code. The HomeLink® indicator light
will flash first slowly, and then rapidly to indicate that the button has
been successfully programmed.
Determining if your garage door uses a rolling code
Determine, in one of the following ways, if your garage door uses a
rolling code system and is manufactured after 1996:
•"
C
•
GY
=
•9
GY
GY
8
*
To train a rolling code garage door opener, follow these instructions
after programming the desired transceiver button according to “Program-
ming the transceiver.” The help of a second person may make training
easier.
%
G
,$
C
% &22 -FF -F%F ,#
G
1
*
9 :
;
:
;
-
9
GY
9
GY
)
$
GY=
The remaining two HomeLink® buttons can be programmed in the
same way. In the event of any problems in programming the
HomeLink® Universal Transceiver, call toll-free 1-800-355-3515
(Internet: www.HomeLink.com).
Operating the HomeLink® Universal Transceiver
Once programmed, the HomeLink® Universal Transceiver can be used
in place of your hand-held transmitters.
To operate, the key must be turned to the “accessory” position (II) or
the engine must be running. Press the programmed HomeLink® button
to activate the garage door, driveway gate, security lighting, home
security system, etc.
Your original hand-held transmitters may, of course, be used at any
time.
Erasing programmed buttons
Individual buttons cannot be erased. To erase all three programmed
buttons:
%
:
; ,1
*
GY=
*2 GYC
-
"
The HomeLink® buttons can be reprogrammed using the procedures
described on the previous page.
,GY
8
1
HomeLink® Universal Transceiver (option)