ignition VOLVO XC90 2014 Owner´s Manual

02 Instruments and controls
Right-side steering wheel lever
02
* Option/accessory, for more information, see Introduction.73
Tailgate wiper/washer
G027127
Intermittent wiping: Press the upper
section of the switch
Neutral position: The wiper is
switched off
Normal (continuous) wiping: Press the
lower section of the switch
Move the lever forward to start the tailgate washer. After washing the rear window, thewiper will make several additional sweeps.
Tailgate wiper and reverse gearIf the front wipers are on and the transmissionis put into reverse gear, the tailgate wiper will go into intermittent wiping function 1
.
If the tailgate wiper is already in normal wip- ing function, the normal wiping function willcontinue.
Rain sensor*
The rain sensor automatically regulates wiper speed according to the amount of water onthe windshield. The sensitivity of the sensor can be adjusted
by twisting ring (1) up (the wipers will sweep the windshield more frequently) or down (thewipers will sweep the windshield less fre-quently).
Activating the rain sensor:1. Turn the ignition key to at least position I
and put the windshield wiper lever inposition 0.
2. Press button (2), see page 72. > A light in the button will light up to indi-cate that the rain sensor is active.
Deactivating the rain sensor:
• Press button (2), see page 72. or •
Move the windshield wiper lever
down to
another position. Moving the lever up will not deactivate the rain sensor. Doing sowill cause the wipers to sweep the wind-shield until the lever is released, at whichtime the wipers return to rain sensormode.
The rain sensor is also deactivated when the key is removed from the ignition.
CAUTION
The rain sensor should be deactivated when washing the vehicle in an automaticcar wash, etc. If the rain sensor function isleft on, the wipers will start inadvertently inthe car wash and could be damaged.
1 Consult your Volvo retailer if you would like to have this function deactivated.

02 Instruments and controls
12-volt sockets
02
80* Option/accessory, for more information, see Introduction.
These 12 volt sockets can be used to plug in certain accessories such as cellular tele-phones, etc. The ignition key must be in at least position I
for the sockets in the front seat and the optional socket at the rear of the center con-sole to function. The maximum current consumption is 10A (120W) if only one of the 12-volt sockets inthe passenger compartment is in use. If boththe front and rear sockets are used at thesame time, the maximum current consump-tion per socket is 7.5A (90W). 12-volt socket in the cargo compartment Fold down the lid to use the socket. This socket can be used even if the ignition isswitched off.NOTE
• If the 12-volt sockets are used while the engine is not running, there is arisk that the vehicle's battery will bedischarged.
• If the ignition is switched off and adevice drawing more than 0.1 A isconnected to a socket, a battery warn-ing will be displayed in the text win-dow.
• The covers should be kept on whenthe auxiliary sockets are not in use.
G028425
12-volt socket at the rear of the center console*
Ashtrays/cigarette lighterThe auxiliary socket can also be used to power a cigarette lighter. Accessory cigarettelighters and ashtrays can be purchased fromyour Volvo retailer.
12-volt socket in the cargo compartment

02 Instruments and controls
Power windows
02
82
Power windows
The power windows are controlled by buttons in the arm rests. The ignition switch must be ON1
(ignition key in position I, II or the engine
running) for the electrically operated windows to function. To lower: Press down the front edge of the button to the first detent ("stop"). To raise: Lightly pull up the front edge of the button to the first detent ("stop").
Auto up/down function (front doors
only):
Either front door window can be opened orclosed automatically. Auto down: Press the front part of the button
as far down as possible and release it imme- diately. To stop the window at any time, pullthe button up. Auto up: Pull the front part of the button up
as far as possible and release it immediately. To stop the window at any time, press thebutton down.
G029571
Power window controls
Front windows
Rear windows
NOTE
If a window is obstructed during auto-up, it will automatically reverse direction andreturn to its starting position. If a window isrepeatedly obstructed during auto-upoperation, an overload protection circuitbreaker will temporarily halt window func-tion. The window will return to normalfunction after a brief cool-down period.
WARNING
Always remove the ignition key when the vehicle is unattended. Make sure that the windows are com- pletely unobstructed before they are oper-ated. Never leave children unattended in the vehicle.
NOTE
To reduce buffeting wind noise if the rear windows are opened, also open the frontwindows slightly.
G029572
1 The power windows will also function after the ignition has been switched off as long as neither of the front doors has been opened.

02 Instruments and controls
Mirrors
02
84* Option/accessory, for more information, see Introduction.
Rearview mirror
G026660
To reduce glare from the headlights of follow- ing vehicles, use the control to switchbetween the normal and night-driving posi-tions.
Normal position
Night position, reduces glare from follow- ing headlights
Autodim function*The autodim function reacts to headlightsfrom following traffic and automaticallyreduces glare.
NOTE
This function is automatically switched off when the gear selector is placed in theReverse position.
Rearview mirror with compass*
G026965
The upper left-hand corner of the rearview mirror has an integrated display that showsthe compass direction toward which the caris pointing. Eight different directions can be displayed:
N, NE, E, SE, S, SW, W and NW.
The display shows your car's orientation with respect to true north. If the compass is activated, it will be dis-played automatically when the ignition is inpostilion II or when the engine is running. Thecompass can be switched off or on by press-ing the inset button on the rear side of themirror (see the inset illustration). This can bedone with straightened paperclip or similarobject. The button is recessed approximately1 in. (2.5 cm) in the mirror.
G026409
Magnetic zonesThe earth is divided into 15 magnetic zones. The compass is initially set for the zone towhich the car was delivered, and shouldalways be adjusted if the car is driven to anew magnetic zone. To do so:

02 Instruments and controls
Mirrors
02
85
1. Switch the ignition to position
II.
2. Press the button on the rear side of the mirror with straightened paperclip or simi- lar object for approximately 3 seconds until
ZONE is displayed. The number of
the current magnetic zone will also be displayed.
3. Press the button repeatedly until the number for the desired zone (1 – 15) isdisplayed.
CALZ
O NE
C A
LZ
O
N
E
G026950
Calibrating the compass
After several seconds, the compass heading will again be displayed, and the change ofmagnetic zones is complete.
Calibrating the compass1. Stop the car in a large, open area, away from traffic.
2. Turn off as many electrical devices in the car as possible to avoid interference withthe compass (e.g. audio system, etc).
3. Using a pen or similar object, hold the button (on the rear side of the mirror) depressed for at least 6 seconds. "
CAL"
will be displayed.
4. Drive slowly in a circle at a maximum speed of 5 m.p.h. (8 km/h) until
CAL is no
longer displayed.
NOTE
This step can also be done by driving nor- mally until CAL is no longer displayed.
Calibration is complete.
Power door mirrors
G029575
The mirror control switches are located on the driver's door armrest. Driver's side: Press the L button (a light in
the switch will light up) to activate the adjust- ment control and then use this control toadjust the driver's door mirror. Passenger's door: Press the R button (a
light in the switch will light up) and then use the adjustment control to adjust the passeng-er's door mirror. After you have adjusted the mirror(s), press the L or R switch again (the light will go out)
to deactivate the adjustment control.

02 Instruments and controls
Power moonroof
02
87
Power moonroof
G007503
To operate the moonroof, turn the ignition key to position I or II, or start the engine. The
moonroof can be operated in two ways:
Tilt position
Sliding moonroof
G027010
Tilt positionOpen: With the moonroof closed, push up the
rear edge of the switch (position 5 in the illus- tration in the center column). Close: Pull down and hold the rear edge of
the switch (position 6 in the illustration in the center column) until the moonroof has closedcompletely.
Sliding moonroofManual open: Pull the switch rearward to
position 3 and hold it until the moonroof hasopened to the position of your choice. Auto open:
Pull the switch as far back as
possible (position 4) and release it to auto-matically slide open the moonroof to the "comfort" 1
position. Pull the switch rearward
again to open the moonroof completely. Manual close: Push the switch to position 2
and hold it until the moonroof has closed completely or to the position of your choice. Auto close: Push the switch forward as far as
possible (position 1) and release it to auto- matically close the moonroof.
CAUTION
• Remove ice and snow before opening the moonroof.
• Do not operate the moonroof if it isfrozen closed.
• Never place heavy objects on themoonroof.
1
A position where the moonroof is not quite fully open, which helps alleviate "rumbling" wind noise.

02 Instruments and controls
Power moonroof
02
88
WARNING
•Never open/close the moonroof if it is obstructed in any way when in opera-tion.
• Never allow a child to operate themoonroof.
• Never extend any object or body partthrough the open moonroof, even ifthe vehicle's ignition is completelyswitched off.
• Never leave a child alone in a vehicle.
If the moonroof is obstructed during auto- close operation, it will automatically reversedirection and return to its starting position. Ifthe moonroof is repeatedly obstructed duringauto-close operation, an overload circuitbreaker will temporarily halt moonroof func-tion. The moonroof will return to normal func-tion after a brief cool-down period.G020157
Sun visorThe optional moonroof also features a sliding sun visor. The visor slides open automaticallywhen the moonroof is opened. The visor mustbe closed manually.
WARNING
The moonroof must never be obstructed in any way when in operation.

02 Instruments and controls
HomeLink®
Wireless Control System*
02
* Option/accessory, for more information, see Introduction.89
Introduction
G030070
The HomeLink 1
Wireless Control System pro-
vides a convenient way to replace up to three hand-held radio-frequency (RF) transmittersused to activate devices such as gate opera-tors, garage door openers, entry door locks,security systems, even home lighting. Addi-tional HomeLink information can be found onthe Internet at www.homelink.com or byphoning the hotline at 1–800–355–3515.
WARNING
• If you use HomeLink to open a garage door or gate, be sure no one is nearthe gate or door while it is in motion.
• When programming a garage dooropener, it is advised to park outside ofthe garage.
• Do not use HomeLink with any garagedoor opener that lacks safety stop andreverse features as required by U.S.federal safety standards (this includesany garage door opener model manu-factured before April 1, 1982). Agarage door that cannot detect anobject - signaling the door to stop andreverse - does not meet current U.S.federal safety standards. For moreinformation, contact HomeLink at:www.homelink.com.
Retain the original transmitter of the RF device you are programming for use in othervehicles as well as for future HomeLink pro-gramming. It is also suggested that upon thesale of the vehicle, the programmed Home-Link buttons be erased for security purposes.Refer to “Resetting HomeLink Buttons” onpage 91.
Programming HomeLink
NOTE
Some vehicles may require the ignition to be switched on or be in the “accessories”position for programming and/or operationof HomeLink. It is also recommended thata new battery be placed in the hand-heldtransmitter of the device being pro-grammed to HomeLink for quicker trainingand accurate transmission of the radio-fre-quency signal. The HomeLink buttonsmust be reset first. When this has beencompleted, Homelink is in learning modeso that you can perform programming.
1. Position the end of your hand-held trans-
mitter 1–3 inches (5–14 cm) away from the HomeLink button you wish to pro-gram while keeping the indicator light inview.
2. Simultaneously press and hold both the chosen HomeLink and hand-held trans-mitter buttons until the HomeLink indica-tor light changes from a slow to a rapidlyblinking light. Now you may release boththe HomeLink and hand-held transmitterbuttons.
1HomeLink and the HomeLink house are registered trademarks of Johnson Controls, Inc.

02 Instruments and controls
HomeLink®
Wireless Control System*
02
* Option/accessory, for more information, see Introduction.91
NOTE
If the ignition is switched off, HomeLink will function for 30 minutes after the driv-er's door has been opened.
Resetting HomeLink Buttons
Use the following procedure to reset (erase programming) from the three HomeLink but-tons (individual buttons cannot be reset butcan be “reprogrammed” as outlined in the fol-lowing section):
1. Press and hold the two outer HomeLink
buttons until the indicator light begins to flash.
2. Release both buttons. > HomeLink is now in the training (orlearning) mode and can be pro-grammed at any time beginning with“Programming” - step 1.
Reprogramming a Single HomeLink Button
To program a device to HomeLink using a HomeLink button previously trained, followthese steps:
1. Press and hold the desired HomeLink button. DO NOT release the button.
2. The indicator light will begin to flash after 20 seconds. Without releasing the Home- Link button, proceed with “Programming”- step 1.
For questions or comments, contact Home-Link at: www.homelink.com or phone 1–800–355–3515. This device complies with FCC rules part 15 and Industry Canada (IC) RSS-210. Operationis subject to the following two conditions: (1)This device may not cause harmful interfer-ence, and (2) This device must accept anyinterference that may be received includinginterference that may cause undesired opera-tion.
NOTE
The transmitter has been tested and com- plies with FCC and IC rules. Changes ormodifications not expressly approved bythe party responsible for compliance couldvoid the user’s authority to operate the device. 2
2
The term “IC:” before the certification/registration number only signifies that Industry Canada technical specifications were met.

03 Climate
Climate control system – general information
03
95
Climate system blower
The climate system blower will be automati- cally switched off when the engine is not run-ning (even if the ignition key is in position I or
II ) to avoid unnecessary battery drain. To
activate the blower, turn the control to thedesired setting. The climate system blower may start auto- matically during a period of up to approxi-mately 50 minutes after the ignition has beenturned off to remove condensation in the A/Cevaporator. It will run for 15 minutes andswitch off automatically.
Passenger compartment blower
Approximately 50 minutes after the ignition is turned off, the blower may come on automati-cally, and run for seven minutes, to removecondensation in the A/C evaporator.
Blower function to reduce battery drain
The climate system's blower functions nor- mally while the engine is running. However, when the engine is switched off (even if the ignition is switched to positions I
or II), the blower control will be automatically
switched off to avoid unnecessary batterydrain. The following points pertain if the ignition ison but the engine in not running:
• To restart the blower, turn the control knob to the setting of your choice.
• After approximately 2 minutes, the blowerspeed will be reduced to avoid batterydrain.
You can reset the blower speed at any time. Please be aware that the system has beendesigned to reduce the blower's speed againafter 2 minutes, until the engine is started. If the battery becomes drained: • LOW BATTERY, FAN IS REDUCED
will
be displayed in the text window in the instrument panel.
• The yellow warning light in the instrumentpanel (see page 58) will also light up.