engine oil YAMAHA BEAR TRACKER 250 2004 Owners Manual

EBU00015
1-CONTENTS
LOCATION OF THE WARNING AND
SPECIFICATION LABELS ....................... 1-1
SAFETY INFORMATION ......................... 2-1
DESCRIPTION AND MACHINE
IDENTIFICATION .................................... 3-1
Identification number records ............... 3-3
Key identification number .................... 3-5
Vehicle identification number ............... 3-7
Model label ........................................... 3-9
CONTROL FUNCTIONS ......................... 4-1
Main switch........................................... 4-1
Indicator lights ..................................... 4-3
Handlebar switches ............................. 4-5
Throttle lever ..................................... 4-11
Speed limiter ...................................... 4-13
Front brake lever ............................... 4-15
Brake pedal and rear brake lever ....... 4-15
Parking brake ..................................... 4-17
Shift pedal ......................................... 4-19
Drive select lever ............................... 4-19
Recoil starter ..................................... 4-21
1234
Fuel tank cap .................................... 4-21
Fuel cock ........................................... 4-23
Starter (choke) .................................. 4-25
Seat.................................................... 4-27
Storage box........................................ 4-31
Front carrier ....................................... 4-31
Rear carrier ........................................ 4-31
Rear shock absorber adjustment ....... 4-33
PRE-OPERATION CHECKS ................... 5-1
Front and rear brakes .......................... 5-5
Fuel ...................................................... 5-9
Engine oil ........................................... 5-13
Final gear oil ...................................... 5-15
Throttle lever ...................................... 5-15
Fittings and fasteners......................... 5-17
Lights ................................................. 5-17
Switches............................................. 5-17
Battery ............................................... 5-17
Tires .................................................. 5-19
How to measure tire pressure ........... 5-23
Tire wear limit .................................... 5-25
5
U4XE65.book Page 1 Tuesday, May 6, 2003 1:38 PM

OPERATION ............................................6-1
Starting a cold engine ...........................6-3
Starting a warm engine ........................6-9
Warming up ..........................................6-9
Drive select lever operation and
reverse driving .................................6-11
Shifting ................................................6-15
To start out and accelerate .................6-17
To decelerate ......................................6-19
Engine break-in ...................................6-21
Parking ...............................................6-23
Parking on a slope .............................6-25
Accessories and loading ....................6-27
RIDING YOUR ATV..................................7-1
Getting to know your ATV .....................7-3
Ride with care and good judgement .....7-5
Be careful where you ride ...................7-27
Turning your ATV ................................7-41
Climbing uphill.....................................7-47
Riding downhill ....................................7-57
Crossing a slope .................................7-61
Crossing through shallow water ..........7-65
Riding over rough terrain ....................7-69
Sliding and skidding ............................7-71
What to do if ........................................7-75
What to do...........................................7-75
67
PERIODIC MAINTENANCE AND
ADJUSTMENT ......................................... 8-1
Owner’s manual and tool kit ................. 8-3
Periodic maintenance/lubrication.......... 8-7
Engine oil ............................................ 8-13
Final gear oil ....................................... 8-21
Spark plug inspection ......................... 8-27
Air filter element cleaning ................... 8-31
Carburetor adjustment ....................... 8-37
Idle speed adjustment ........................ 8-39
Valve clearance adjustment .............. 8-41
Throttle lever adjustment ................... 8-41
Front brake pad check ........................ 8-43
Rear brake shoe inspection ............... 8-43
Brake fluid level check ........................ 8-45
Brake fluid replacement ...................... 8-47
Front brake lever free play.................. 8-49
Rear brake adjustment ....................... 8-51
Adjusting the rear brake light switch ... 8-57
Clutch adjustment .............................. 8-59
Cable inspection and lubrication......... 8-61
Brake lever and brake pedal
lubrication ........................................ 8-63
Steering shaft lubrication .................... 8-63
Wheel removal.................................... 8-65
Wheel installation ............................... 8-67
Battery ............................................... 8-69
8
U4XE65.book Page 2 Tuesday, May 6, 2003 1:38 PM

4-21 1. Recoil starter
1. Lanceur à réenroulement
1. Arranque por tracción de cable
1. Fuel tank cap
1. Bouchon de réservoir de carburant
1. Tapón del depósito de combustible
EBU00591
Recoil starter
Firmly grasp the handle and pull slightly until en-
gagement can be felt. Then pull forcefully, being
careful not to pull the rope all the way out.
WARNING
Put the transmission in neutral and set the
parking brake before starting the engine or the
ATV could start to move unexpectedly, which
could cause an accident.
EBU00092
Fuel tank cap
Remove the fuel tank cap by turning it counter-
clockwise.
U4XE65.book Page 21 Tuesday, May 6, 2003 1:38 PM

5-1
EBU00113
1-PRE-OPERATION CHECKS
Before using this machine, check the following points:
ITEM ROUTINE PAGE
Front brakeCheck operation, free play, fluid level and fluid leakage.
Fill with DOT 4 brake fluid if necessary.5-5–5-7,
8-45–8-49
Rear brakeCheck operation, condition and free play.
Adjust if necessary.5-5–5-7,
8-51–8-55
FuelCheck fuel level.
Fill with fuel if necessary.5-9–5-11
Engine oilCheck oil level.
Fill with oil if necessary.5-13, 8-13–8-19
Final gear oilCheck for leakage. 5-15, 8-21–8-25
ThrottleCheck for proper throttle cable operation. 5-15, 8-41
Wheels and tiresCheck tire pressure, wear and damage.5-19–5-25,
8-65–8-67
Fittings and fastenersCheck all fittings and fasteners. 5-17
Lights and switchesCheck for proper operation. 5-17, 8-79–8-85
BatteryCheck fluid level.
Fill with distilled water if necessary.5-17, 8-69–8-75
U4XE65.book Page 1 Tuesday, May 6, 2003 1:38 PM

5-13
EBU10842
Engine oil
Make sure the engine oil is at the specified level.
Add oil as necessary. (See pages 8-13–8-19.)CAUTION:_

In order to prevent clutch slippage (since
the engine oil also lubricates the clutch),
do not mix any chemical additives. Do not
use oils with a diesel specification of “CD”
or oils of a higher quality than specified. In
addition, do not use oils labeled “ENERGY
CONSERVING II” or higher.


Make sure that no foreign material enters
the crankcase.
_
Recommended engine oil type and quantity:
See page 10-2.
U4XE65.book Page 13 Tuesday, May 6, 2003 1:38 PM

6-7
NOTE:

If the engine fails to start, release the start
switch, then push the start switch again.
Pause a few seconds before the next at-
tempt. Each cranking should be as short as
possible to preserve battery energy. Do not
crank the engine more than 10 seconds on
each attempt.


If the battery is discharged, pull the recoil
starter to start the engine.
_7. If the engine is started with the starter (choke)
in position
1, the starter (choke) should be
returned to position
2 to warm up the en-
gine. If the engine is started with the starter
(choke) in position
2, keep the starter
(choke) in this position to warm up the en-
gine.
8. Continue warming up the engine until it idles
smoothly and return the starter (choke) to po-
sition
3 before riding.CAUTION:
See the “Engine break-in” section prior to op-
erating engine for the first time.
U4XE65.book Page 7 Tuesday, May 6, 2003 1:38 PM

8-7
EBU00262
PERIODIC MAINTENANCE/LUBRICATION
ITEM ROUTINEINITIAL EVERY
1
month3
months6
months6
months1
year
Valves*Check valve clearance.
Adjust if necessary.
Spark plugCheck condition.
Adjust gap and clean.
Replace if necessary.Air filter elementClean.
Replace if necessary.Every 20–40 hours
(More often in wet or dusty areas.)
Carburetor*Check starter (choke) operation.
Adjust engine idling speed.Cylinder head breather
system*Check breather hose for cracks or damage.
Replace if necessary.Exhaust system*Check for leakage.
Retighten if necessary.
Replace gasket if necessary.Fuel line*Check fuel hose for cracks or damage.
Replace if necessary.Engine oil
Replace (Warm engine before draining).Engine oil filter element
Clean.Engine oil strainer
Clean.Final gear oilCheck oil level/oil leakage.
Replace.Front brake*Check operation/fluid leakage/see NOTE page 8-8.
Correct if necessary.Rear brake*Check operation.
Adjust if necessary.Clutch*Check operation.
Adjust if necessary.U4XE65.book Page 7 Tuesday, May 6, 2003 1:38 PM

8-13 1. Engine oil filler cap
2. Dipstick
3. Maximum level mark
4. Minimum level mark
1. Bouchon de remplissage d’huile de moteur
2. Jauge
3. Repère de niveau maximum
4. Repère de niveau minimum
1. Tapa del filtro de aceite de motor
2. Varilla de nivel de aceite
3. Marca de nivel máximo
4. Marca de nivel mínimo
EBU11002
Engine oil
Engine oil level measurement
1. Place the machine on a level surface.
2. Warm up the engine for several minutes and
stop it. Wait at least ten minutes for the oil to
drain back into the crankcase before check-
ing the oil level.NOTE:_ Be sure to wait at least ten minutes until the oil lev-
el settles before checking. _3. Remove the engine oil filler cap and wipe the
dipstick off with a clean rag. Insert the dip-
stick in the filler hole without screwing it in.
4. Remove the dipstick and check the oil level.
5. The oil level should be between the maxi-
mum and minimum marks. If the level is low,
add oil to raise it to the proper level.
6. Install the engine oil filler cap.CAUTION:_ Make sure no foreign material enters the
crankcase. _
U4XE65.book Page 13 Tuesday, May 6, 2003 1:38 PM

8-15 1. Engine oil drain bolt 2. O-ring
3. Compression spring 4. Engine oil strainer
1. Boulon de vidange de l’huile moteur
2. Joint torique
3. Ressort de compression
4. Crépine à huile de moteur
1. Perno de drenaje del aceite de motor
2. Junta tórica
3. Muelle de compresión
4. Tamiz de aceite de motor
Engine oil replacement and oil filter element
cleaning
1. Place the machine on a level surface.
2. Warm up the engine for several minutes and
stop it.
3. Place a container under the engine to collect
the used oil.
4. Remove the engine oil filler cap and then the
drain bolt to drain the oil.CAUTION:_ When removing the drain bolt, the compres-
sion spring, oil strainer and O-ring will fall out.
Take care not to lose these parts. _
U4XE65.book Page 15 Tuesday, May 6, 2003 1:38 PM

8-17 1. Oil filter cover
2. Engine oil filter element
3. O-ring
1. Couvercle du filtre à huile
2.Élément du filtre à huile de moteur
3. Joint torique
1. Tapa del filtro de aceite
2. Elemento del filtro de aceite de motor
3. Junta tórica
5. Remove the oil filter cover and oil filter ele-
ment.
6. Clean the oil strainer and oil filter element
with solvent.
7. Inspect the O-ring and replace it if damaged.
8. Install the oil filter element, O-ring and oil filter
cover.
9. Install the oil strainer, compression spring,
O-ring and drain bolt.
10. Tighten the drain bolt and the oil filter cover
bolts to the specified torques.CAUTION:_ Before installing the drain bolt, be sure to in-
stall the O-ring, compression spring and oil
strainer. _11. Fill the engine with oil and install the engine
oil filler cap. Tightening torque:
Drain bolt (engine):
43 Nm (4.3 m·kgf)
Oil filter cover bolt:
10 Nm (1.0 m·kgf)
U4XE65.book Page 17 Tuesday, May 6, 2003 1:38 PM