light YAMAHA CYGNUS 125 2011 Owner's Manual

1
2
3
4
5
6
7
8
9
7-1
EAU25991
SCOOTER CARE AND STORAGE
EAU25991
SCOOTER CARE AND STORAGE
EAU37833
Matte color caution
ECA15192
NOTICESome models are equipped with
matte colored nished parts. Be
sure to consult a Yamaha dealer for
advice on what products to use be-
fore cleaning the vehicle.
Using a brush, harsh chemical
products or cleaning compounds
when cleaning these parts will
scratch or damage their surface.
Wax also should not be applied to
any matte colored nished parts.
EAU26094
CareWhile the open design of a scooter
reveals the attractiveness of the tech-
nology, it also makes it more vulner-
able. Rust and corrosion can develop
even if high-quality components are
used. A rusty exhaust pipe may go
unnoticed on a car, however, it de-
tracts from the overall appearance of
a scooter. Frequent and proper care
does not only comply with the terms of
the warranty, but it will also keep your
scooter looking good, extend its life
and optimize its performance.
Before cleaning
1. Cover the muffl er outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and cov-
ers as well as all electrical cou-
plers and connectors, including
the spark plug cap, are tightly
installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and
a brush, but never apply such
products onto seals, gaskets and
wheel axles. Always rinse the dirt
and degreaser off with water.
Cleaning
ECA10783
NOTICE● Avoid using strong acidic
wheel cleaners, especially
on spoked wheels. If such
products are used on hard-to-
remove dirt, do not leave the
cleaner on the affected area
any longer than instructed.
Also, thoroughly rinse the area
off with water, immediately dry
it, and then apply a corrosion
protection spray.● Improper cleaning can dam-
age plastic parts (such as
cowlings, panels, windshields,
headlight lenses, meter lenses,
etc.) and the muf ers. Use only
a soft, clean cloth or sponge
with water to clean plastic.
However, if the plastic parts
cannot be thoroughly cleaned
2('KPFF
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"

1
2
3
4
5
6
7
8
9
7-2
EAU25991
SCOOTER CARE AND STORAGE
with water, diluted mild deter-
gent with water may be used.
Be sure to rinse off any deter-
gent residue using plenty of
water, as it is harmful to plastic
parts.
● Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
uid, antifreeze or electrolyte.● Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the
following areas: seals (of wheel
and swingarm bearings, fork
and brakes), electric compo-
nents (couplers, connectors,
instruments, switches and
lights), breather hoses and
vents.● For vehicles equipped with a
windshield: Do not use strong
cleaners or hard sponges
as they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the
windshield is scratched, use a
quality plastic polishing com-
pound after washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily
if the area is covered with a wet cloth
for a few minutes before cleaning.
After riding in the rain, near the sea or on salt-sprayed roadsSince sea salt or salt sprayed on the
roads during winter are extremely cor-
rosive in combination with water, carry
out the following steps after each ride
in the rain, near the sea or on salt-
sprayed roads.TIPSalt sprayed on roads in the winter
may remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the en-
gine has cooled down.
NOTICE:
Do not use warm water since it
increases the corrosive action
of the salt.
[ECA10791]
2. Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, sur-
faces to prevent corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
2('KPFF
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"

1
2
3
4
5
6
7
8
9
7-3
EAU25991
SCOOTER CARE AND STORAGE
duced discoloring of stainless-
steel exhaust systems can be
removed through polishing.)
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, includ-
ing chrome- and nickel-plated,
surfaces.
4. Use spray oil as a universal
cleaner to remove any remaining
dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely
before storing or covering it.
EWA10942
WARNING
Contaminants on the brakes or
tires can cause loss of control.● Make sure that there is no oil
or wax on the brakes or tires.
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires
with warm water and a mild de-
tergent.
● Before operating the vehicle,
test its braking performance
and cornering behavior.
ECA10800
NOTICE● Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.● Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.● Avoid using abrasive polishing
compounds as they will wear
away the paint.
TIP● Consult a Yamaha dealer for ad-
vice on what products to use.● Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from
the lens.
2('KPFF
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"

1
2
3
4
5
6
7
8
9
8-2
SPECIFICATIONS
Size
110/70-12 47L
Manufacturer/model
CHENG SHIN / C-992NRear tireType
Tubeless
Size
120/70-12 58L
Manufacturer/model
CHENG SHIN / C-6007LoadingMaximum load
157 kg (346 lb)Tire air pressure (measured on cold
tires)Loading condition
0-90 kg (0-198 lb)
Front
175 kPa (1.75 kgf/cm
2, 25 psi, 1.75 bar)
Rear
200 kPa (2.00 kgf/cm2, 29 psi, 2.00 bar)
Loading condition
90 kg - maximum load
Front
200 kPa (2.00 kgf/cm2, 29 psi, 2.00 bar)
Rear
225 kPa (2.25 kgf/cm2, 33 psi, 2.25 bar)
Front wheelWheel type
Cast wheel
Rim size
J12 X MT2.75
Rear wheelWheel type
Cast wheel
Rim size
J12 X MT3.00Front brakeType
Single disc brake
Operation
Right hand operation
Recommended fl uid
DOT 4Rear brakeType
Drum brake
Operation
Left hand operationFront suspensionType
Telescopic fork
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
78.0 mm (3.07 in)Rear suspensionType
Unit swing
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
95.5 mm (3.76 in)Electrical systemIgnition system
TCICharging system
AC magneto
BatteryModel
MF (YT7B-BS)
Voltage, capacity
12 V, 6.5 AhHeadlightBulb type
Halogen bulbBulb voltage, wattage x quantityHeadlight
12 V, 60 W/55 W x 1
Tail/brake light
12 V, 5.0 W/21.0 W x 1
Front turn signal light
12 V, 10.0 W x 2
Rear turn signal light
12 V, 10.0 W x 2
Auxiliary light
12 V, 5.0 W x 2
Meter lighting
LED x 2
High beam indicator light
LED x 1
Turn signal indicator light
LED x 1FusesMain fuse
20.0 A
Headlight fuse
15.0 A
Taillight fuse
7.5 A
2('KPFF
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"

INDEXAAcceleration and deceleration................... 5-2
Air fi lter and V-belt case air fi lter
elements ............................................... 6-13
Auxiliary light bulb, replacing .................. 6-29BBattery..................................................... 6-24
Brake fl uid, changing .............................. 6-20
Brake fl uid level, checking ...................... 6-19
Brake lever, front....................................... 3-6
Brake lever, rear ....................................... 3-6
Brake levers, lubricating.......................... 6-21
Brake lever free play, checking ............... 6-18
Brake pads and shoes, checking ............ 6-19
Braking ...................................................... 5-2CCables, checking and lubricating ............ 6-21
Care .......................................................... 7-1
Catalytic converters .................................. 3-9
Centerstand and sidestand, checking and
lubricating ............................................. 6-22DDimmer switch .......................................... 3-6EEngine break-in ......................................... 5-3
Engine oil and oil strainer........................ 6-10
Engine trouble warning light...................... 3-2FFinal transmission oil .............................. 6-12
Front fork, checking ................................ 6-23
Fuel ........................................................... 3-7
Fuel consumption, tips for reducing .......... 5-3
Fuel tank cap ............................................ 3-7
Fuses, replacing...................................... 6-26
HHandlebar switches................................... 3-5
Headlight bulb, replacing ........................ 6-27
High beam indicator light .......................... 3-2
Horn switch ............................................... 3-6IIdentifi cation numbers ............................... 9-1
Ignition circuit cut-off system................... 3-12
Indicator and warning lights ...................... 3-2KKeyhole cover ........................................... 3-2
Kickstarter ................................................. 3-9MMaintenance, emission control system ..... 6-3
Maintenance and lubrication, periodic ...... 6-4
Main switch/steering lock .......................... 3-1
Matte color, caution................................... 7-1
Model label................................................ 9-1
Multi-function display ................................ 3-3PPanels, removing and installing ................ 6-7
Parking ...................................................... 5-4
Part locations ............................................ 2-1RRear brake lever free play, adjusting ...... 6-18SSafe-riding points ...................................... 1-5
Safety information ..................................... 1-1
Seat......................................................... 3-10
Sidestand ................................................ 3-11
Spark plug, checking................................. 6-8
Specifi cations ............................................ 8-1
Speedometer ............................................ 3-3
Starting off................................................. 5-2Starting the engine .................................... 5-1
Start switch ............................................... 3-6
Steering, checking .................................. 6-23
Storage ..................................................... 7-4
Storage compartments............................ 3-10
TTail/brake light bulb or rear turn signal light
bulb, replacing ...................................... 6-28
Throttle grip and cable, checking and
lubricating ............................................. 6-21
Throttle grip free play, checking .............. 6-15
Tires ........................................................ 6-16
Tool kit ...................................................... 6-2
Troubleshooting ...................................... 6-29
Troubleshooting chart ............................. 6-31
Turn signal indicator light .......................... 3-2
Turn signal light bulb (front), replacing.... 6-28
Turn signal switch ..................................... 3-6VValve clearance ...................................... 6-15
Vehicle identifi cation number .................... 9-1WWheels .................................................... 6-17
Wheel bearings, checking ....................... 6-24
2('KPFF
J`.,*f J`.,Q/f2J`.,`oJ`.,I\6"