lights YAMAHA FJR1300A 2003 User Guide
Page 88 of 112
PERIODIC MAINTENANCE AND MINOR REPAIR
6-35
65. Install the headlight bulb cover,
and then connect the coupler.
6. Install the panel.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU05022
Replacing an auxiliary light
bulb This motorcycle is equipped with two
auxiliary lights. If an auxiliary light bulb
burns out, replace it as follows.
1. Remove panel B (if replacing the
left auxiliary light bulb) or panel C
(if replacing the right auxiliary light
bulb). (See page 6-6 for panel re-
moval and installation proce-
dures.)
2. Remove the auxiliary light socket
(together with the coupler) by turn-
ing the socket counterclockwise.3. Remove the defective bulb by pull-
ing it out.
4. Insert a new bulb into the socket.
5. Install the auxiliary light socket (to-
gether with the coupler) by push-
ing it in and turning it clockwise.1. Auxiliary light socket
2. Auxiliary light coupler
1. Auxiliary light bulb
U5JWE2.book Page 35 Wednesday, November 6, 2002 3:32 PM
Page 95 of 112
MOTORCYCLE CARE AND STORAGE
7-2
7
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.
Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the wind-
shield is scratched, use a quali-
ty plastic polishing compound
after washing.
_After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.After riding in the rain, near the sea or
on salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.NOTE:_ Salt sprayed on roads in the winter may
remain well into spring. _1. Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
CAUTION:_ Do not use warm water since it in-
creases the corrosive action of the
salt. _2. After drying the motorcycle, apply
a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces to prevent cor-
rosion.
U5JWE2.book Page 2 Wednesday, November 6, 2002 3:32 PM
Page 108 of 112
INDEXAABS (For FJR1300A only)...................... 3-13
ABS warning light
(For FJR1300A only) .............................3-5
Accessory box ....................................... 3-19
Air filter element, cleaning ...................... 6-15
Anti-theft alarm ........................................3-9
Auxiliary light bulb, replacing .................. 6-35BBattery ................................................... 6-31
Brake and clutch fluid levels,
checking .............................................. 6-23
Brake and clutch fluids, changing........... 6-25
Brake and clutch levers,
checking and lubricating ...................... 6-27
Brake and shift pedals,
checking and lubricating ...................... 6-26
Brake lever............................................. 3-12
Brake light switch (rear), adjusting ......... 6-22
Brake pads, checking............................. 6-22
Brake pedal............................................ 3-12
Brake pedal position, adjusting .............. 6-21CCables, checking and lubricating............ 6-25
Care.........................................................7-1
Catalytic converter ................................. 3-16
Centerstand and sidestand,
checking and lubricating ...................... 6-27
Clutch lever ........................................... 3-11
Clutch lever free play ............................. 6-21
Conversion table ..................................... 8-5
Coolant level, checking .......................... 6-13DDimmer switch ......................................... 3-9EEngine break-in ....................................... 5-3
Engine idling speed, checking ............... 6-16
Engine oil and oil filter cartridge ............... 6-9
Engine stop switch................................. 3-10
Engine trouble warning light .................... 3-5FFinal gear oil .......................................... 6-12
Front fork, adjusting ............................... 3-19
Front fork, checking ............................... 6-29
Fuel ....................................................... 3-15
Fuel consumption, tips for reducing ......... 5-3
Fuel tank breather hose ......................... 3-16
Fuel tank cap ......................................... 3-14
Fuses, replacing .................................... 6-32HHandlebar switches ................................. 3-9
Hazard switch ........................................ 3-10
Headlight bulb, replacing ....................... 6-33
High beam indicator light ......................... 3-5
Horn switch ............................................. 3-9
IIdentification numbers ..............................9-1
Ignition circuit cut-off system ..................3-24
Immobilizer system..................................3-1
Immobilizer system indicator light.............3-4
Indicator and warning lights......................3-4KKey identification number .........................9-1LLocks for optional side cases and
travel trunk ...........................................3-23MMain switch/steering lock .........................3-2
Model label ..............................................9-2
Multi-function display................................3-7NNeutral indicator light ...............................3-5OOil level warning light ...............................3-5PPanels, removing and installing ................6-5
Parking.....................................................5-4
Part locations ...........................................2-1
Pass switch ..............................................3-9
Periodic maintenance and
lubrication chart .....................................6-2
Pre-operation check list ............................4-1
E_5jwIX.fm Page 1 Monday, November 11, 2002 10:01 AM
Page 109 of 112
INDEX
SSafety information.................................... 1-1
Seats ..................................................... 3-17
Passenger seat ................................ 3-17
Rider seat ........................................ 3-17
Shifting .................................................... 5-2
Shift pedal ............................................. 3-11
Shift points (for Switzerland only)............. 5-3
Shock absorber assembly, adjusting ..... 3-21
Sidestand .............................................. 3-23
Spark plugs, checking ............................. 6-7
Specifications .......................................... 8-1
Speedometer ........................................... 3-6
Starting the engine .................................. 5-1
Start switch ............................................ 3-10
Steering, checking ................................. 6-29
Storage.................................................... 7-4
Storage compartment ............................ 3-18
Swingarm pivots, lubricating .................. 6-28TTachometer ............................................. 3-6
Throttle cable free play, adjusting .......... 6-17
Throttle grip and cable,
checking and lubricating ...................... 6-25
Tires ...................................................... 6-17
Tool kit..................................................... 6-1
Troubleshooting..................................... 6-36
Troubleshooting charts .......................... 6-37
Turn signal indicator lights ....................... 3-4
Turn signal light or tail/brake light bulb,
replacing ............................................. 6-36
Turn signal switch ................................... 3-9VValve clearance, adjusting .................... 6-17
Vehicle identification number................... 9-1WWheel bearings, checking ..................... 6-30
Wheels .................................................. 6-20
Windshield position adjusting switch ....... 3-9
U5JWE2.book Page 2 Wednesday, November 6, 2002 3:32 PM