stop start YAMAHA GP1300R 2005 Owners Manual

1-13
E

Do not attempt to modify this watercraft!
Modifications to your watercraft may
reduce safety and reliability, and render
the watercraft unsafe or illegal for use.

Attach the engine shut-off cord (lanyard)
to wrist and keep it free from the handle-
bars so that the engine stops if the opera-
tor falls off. After riding, remove the
engine shut-off cord from the watercraft to
avoid accidental starting or unauthorized
use by children or others.

Scan carefully for swimmers and stay
away from swimming areas. Swimmers
are hard to see and you could acciden-
tally hit someone in the water.

Avoid being hit by another boat! You
should always take the responsibility to
watch for traffic; other boaters may not be
watching for you. If they do not see you,
or you maneuver more quickly than other
boaters expect, you risk a collision.

Maintain a safe distance from other boats
or watercraft, and also watch for boats’ ski
ropes or fishing lines. Obey the “Safe
boating rules” and be sure to check
behind you before making a turn. (See
Safe boating rules on page 1-16.)
EJU13820
Recommended equipment
The following items should be carried on
board your watercraft:

Sound-signaling device
You should carry a whistle or other sound-
signaling device that can be used to sig-
nal other boats.

Visual distress signals
It is recommended that an authority-
approved pyrotechnic device be stored in
a waterproof container on your watercraft.
A mirror can also be used as an emer-
gency signal. Contact your Yamaha
dealer for more information.

Watch
A watch is helpful so you will know how
long you have been operating.

Towline
A towline can be used to tow a disabled
watercraft in an emergency.
UF1G72.book Page 13 Thursday, September 30, 2004 2:28 PM

1-14
E
EJU20020
Hazard information

Never start the engine or let it run for any
length of time in an enclosed area.
Exhaust fumes contain carbon monoxide,
a colorless, odorless gas that may cause
loss of consciousness and death within a
short time. Always operate the watercraft
in an open area.

Do not start engine on land until everyone
is away from stern. Hot water and steam
spurting from exhaust outlet can cause
serious burns.

Hot muffler surfaces can cause serious
burns. Do not touch any muffler surface
during or after engine operation. Catalytic
converter gets hotter after engine stops.
EJU20030
Watercraft characteristics

Jet thrust turns the watercraft. Releasing
the throttle lever completely produces
only minimum thrust. If you are traveling
at speeds above trolling, you will have
rapidly decreasing ability to steer without
throttle. This model has the Yamaha
Engine Management System (YEMS)
that includes an Off-Throttle Steering
(OTS) system. It will activate at planing
speeds should you attempt to steer the
watercraft after releasing the throttle lever.
The OTS system assists in turning by
continuing to supply some thrust while the
watercraft is decelerating, but you can
turn more sharply if you apply throttle
while turning the handlebars. The OTS
system does not function below planing
speeds or when the engine is off. Once
the engine slows down, the watercraft will
no longer turn in response to handlebar
input until you apply throttle again or you
reach trolling speed. Practice turning in
an open area without obstructions until
you have a good feel for this maneuver.

This watercraft is water-jet propelled. The
jet pump is directly connected to the
engine. This means that jet thrust will pro-
duce some movement whenever the
engine is running. There is no “neutral”
position.
UF1G72.book Page 14 Thursday, September 30, 2004 2:28 PM

E
2
EJU10070
FEATURES AND
FUNCTIONS
Location of main components .............. 2-1
Operation of controls and other
functions ................................................... 2-5
Seat ........................................................ 2-5
Hood ....................................................... 2-6
Fuel tank filler cap .................................. 2-6
Oil tank filler cap ..................................... 2-6
Engine stop switch ................................. 2-7
Engine shut-off switch ............................ 2-7
Throttle lever .......................................... 2-7
Start switch ............................................. 2-8
Cooling water pilot outlet ....................... 2-8
Steering system ..................................... 2-9
Quick Shift Trim System (QSTS)
selector ................................................. 2-10
Handgrip ............................................... 2-11
Engine overheat warning system ........ 2-12
Exhaust temperature warning
system .................................................. 2-13
Yamaha Engine Management System
(YEMS) ................................................. 2-14
Multifunction information center .......... 2-15
Tachometer .......................................... 2-16
Speedometer ....................................... 2-16
Fuel meter ............................................ 2-16
Hour meter/Voltmeter .......................... 2-17
Fuel warning indicator .......................... 2-17
Oil warning indicator ............................ 2-18
Check engine warning indicator .......... 2-18
Engine overheat warning indicator ...... 2-19
Exhaust temperature warning
indicator ................................................ 2-19
Storage compartments ........................ 2-20
Yamaha Adjustable Sponson (YAS) ... 2-21
UF1G72.book Page 1 Thursday, September 30, 2004 2:28 PM

2-3
E
1Engine shut-off cord (lanyard)
Attach to wrist so that the engine stops if the
operator falls off the watercraft.
2Engine stop switch
Push to stop the engine normally.
3Clip
Insert into the engine shut-off switch to enable
starting of the engine.
Remove to stop the engine or prevent acci-
dental star ting of the engine or unauthorized
use of the watercraft.
4Quick Shift Trim System (QSTS) selector
Use to select the trim angle of the watercraft.
5Engine shut-off switch
Remove the clip to stop the engine and dis-
able it from starting.
6Start switch
Push to start the engine.
7Multifunction information center
Use to check watercraft operation.8Throttle lever
Use to accelerate and decelerate.
9Oil tank filler cap
0Stern drain plugs
Use to drain water in the bilge when the water-
craft is on dry land.
AJet thrust nozzle
Changes the direction of jet thrust according
to handlebar position.
BRide plate
UF1G72.book Page 3 Thursday, September 30, 2004 2:28 PM

2-7
E
EJU10150
Engine stop switch
Push this switch 1 (red button) to stop
the engine normally.
EJU10160
Engine shut-off switch
Insert the clip 1, on the end of the engine
shut-off cord 2, under the engine shut-off
switch 3 (black button). The engine will stop
automatically when the clip is removed from
the switch, such as if the operator falls off
the watercraft.
WARNING@
Always attach the engine shut-off cord
to your wrist and the clip to the engine
shut-off switch BEFORE starting the
engine.

To prevent accidental starting of the
engine or unauthorized use by chil-
dren or others, always remove the clip
from the shut-off switch when the
engine is not running.
@
EJU10180
Throttle lever
Squeeze the throttle lever 1 to increase
engine speed.
Release the throttle lever to decrease
engine speed or to return it to the idle posi-
tion.
UF1G72.book Page 7 Thursday, September 30, 2004 2:28 PM

2-8
E
EJU18610
Start switch
Push the start switch 1 (green button) to
start the engine.
NOTE:@ The engine will not start when the clip is
removed from the engine shut-off switch or if
the throttle lever is squeezed.
@
EJU10201
Cooling water pilot outlet
This watercraft is equipped with cooling
water pilot outlets.
When the engine is running, cooling
water is circulated in the engine, and then it
is discharged from the pilot outlets.
To check for proper operation of the cool-
ing system, check that water is being dis-
charged from the pilot outlets. If water is not
being discharged from the outlets, cooling
water may not be circulating in the engine.
When this occurs, stop the engine and
check for the cause. (See pages 2-12 and
5-4 for further instructions.)
NOTE:@ If the cooling water passages are dry, it will
take about 20 seconds for the water to reach
the outlet after the engine is started.
@
UF1G72.book Page 8 Thursday, September 30, 2004 2:28 PM

2-12
E
EJU20450
Engine overheat warning
system
This model is equipped with an engine
overheat warning system.
If the engine starts to overheat, the warn-
ing light and the engine overheat warning
indicator begin to blink, and the buzzer
sounds intermittently.
When this occurs, reduce the engine
speed and beach the watercraft. Check for
water discharge. If there is no discharge of
water at the cooling water pilot outlet, whole
the engine is running, check the intake grate
and impeller for clogging.
WARNING@ Before attempting to remove weeds or
debris from the intake grate or impeller,
shut the engine off and remove the clip
from the engine shut-off switch. Severe
injury or death could result from coming
in contact with the rotating parts of the
jet pump.
@
CAUTION:@ This watercraft is equipped with a cata-
lytic converter.

Return to shore at low speed if over-
heat warning indicator and buzzer
come on. If you ignore these signals,
engine will stop running and cannot be
restarted until exhaust system cools
down.

Have your watercraft inspected and
serviced by a Yamaha dealer if engine
stops due to overheating.
@
UF1G72.book Page 12 Thursday, September 30, 2004 2:28 PM

2-13
E
If the overheat warning is ignored, engine
and exhaust system heat may increase, par-
ticularly if the watercraft is operated at
higher speeds. When this occurs, the warn-
ing light, the engine overheat warning indi-
cator and the buzzer will change from
intermittently to continuously on, and the
overheat system will stop ignition to the
engine to reduce the risk of severe over-
heating. The engine cannot be started until
it cools down, so it may be necessary to
have the watercraft towed back to the
beach. (See “Towing the watercraft” on page
5-7 for towing procedures.)
NOTE:@ Press the select button on the multifunction
information center to stop the buzzer.
@
EJU20460
Exhaust temperature warning
system
This model is equipped with an exhaust
temperature warning system.
If the exhaust temperature gets too hot,
the warning light and exhaust temperature
warning indicator begin to blink, and the
buzzer sounds intermittently.
When this occurs, reduce engine speed
and beach the watercraft to allow the
exhaust system to cool down.
WARNING@ Hot muffler surfaces can cause serious
burns. Do not touch any muffler surface
during or after engine operation. The cat-
alytic converter gets hotter after the
engine stops.
@
UF1G72.book Page 13 Thursday, September 30, 2004 2:28 PM

2-15
E
EJU20161
Multifunction information
center
This meter contains following functions for
the help and convenience of operation.
1
Tachometer
2
Speedometer
3
Hour meter/Voltmeter
4
Fuel meter
5
Warning light
6
Fuel warning indicator
7
Engine overheat warning indicator
8
Oil warning indicator
9
Exhaust temperature warning indicator
0
Check engine warning indicator
A
Select button
CAUTION:@
Do not run the engine over 4,000 r/min
to check the meter for operation on
land. The engine could overheat or the
catalytic converter could result in seri-
ous damage.

Use the specified resistor-type spark
plug and cap, otherwise the meter may
function erratically.
@
NOTE:@ All display light up and the buzzer sounds
twice after the engine starts. Then, the
meter will operate normally after few sec-
onds. The current display will continue to
operate for 25 seconds after the engine
stops.
@
UF1G72.book Page 15 Thursday, September 30, 2004 2:28 PM

E
3
EJU10400
OPERATION
Fuel and oil ............................................... 3-1
Gasoline ................................................. 3-1
2-stroke engine oil .................................. 3-3
Filling the fuel tank ................................. 3-4
Filling the oil tank ................................... 3-5
Pre-operation checks .............................. 3-6
Pre-operation check list ......................... 3-6
Pre-operation check points .................... 3-7
Operation ................................................ 3-16
Engine break-in .................................... 3-16
Starting the engine ............................... 3-18
Stopping the engine ............................. 3-20
Leaving the watercraft ......................... 3-20
Operating your watercraft .................... 3-21
Getting to know your watercraft ........... 3-21
Learning to operate your watercraft .... 3-21
Riding watercraft with a passenger ..... 3-22
Starting the watercraft .......................... 3-23
Boarding and starting in deep water ... 3-25
Capsized watercraft ............................. 3-27
Turning the watercraft .......................... 3-29
Stopping the watercraft ........................ 3-31
Beaching the watercraft ....................... 3-32
Docking the watercraft ......................... 3-32
Rough water operation ........................ 3-32
Post-operation checks ......................... 3-33
Transporting .......................................... 3-35
UF1G72.book Page 1 Thursday, September 30, 2004 2:28 PM