light YAMAHA GRIZZLY 350 2010 Owners Manual

EBU17420
TABLE OF CONTENTS
LOCATION OF THE WARNING AND
SPECIFICATION LABELS ............................ 1-1
SAFETY INFORMATION .............................. 2-1
DESCRIPTION .............................................. 3-1
Left view ...................................................... 3-1
Right view.................................................... 3-1
Controls and instruments ............................ 3-2
INSTRUMENT AND CONTROL
FUNCTIONS .................................................. 4-1
Main switch ................................................ 4-1
Indicator lights and warning light ................ 4-2
Speedometer .............................................. 4-3
Handlebar switches .................................... 4-4
Throttle lever .............................................. 4-5
Speed limiter .............................................. 4-6
Front brake lever ........................................ 4-7
Brake pedal and rear brake lever ............... 4-7
Parking brake ............................................. 4-8
Drive select lever ........................................ 4-9
Recoil starter .............................................. 4-9
Fuel tank cap ............................................ 4-10Fuel ...........................................................4-10
Fuel cock ..................................................4-12
Starter (choke) ..........................................4-13
Seat ..........................................................4-14
Storage compartment ...............................4-15
Front carrier ..............................................4-16
Rear carrier ...............................................4-16
Adjusting the front shock absorber
assemblies ..............................................4-16
Adjusting the rear shock absorber
assembly .................................................4-17
PRE-OPERATION CHECKS ..........................5-1
Fuel .............................................................5-3
Engine oil ....................................................5-3
Final gear oil ...............................................5-3
Differential gear oil ......................................5-3
Front and rear brakes .................................5-3
Throttle lever ...............................................5-4
Tires ............................................................5-4
Chassis fasteners .......................................5-6
Instruments, lights and switches .................5-6U1AB60E0.book Page 1 Wednesday, April 29, 2009 10:19 AM

Checking the front brake lever free
play ......................................................... 8-30
Adjusting the brake pedal and rear brake
lever free play and checking the brake
pedal position ......................................... 8-31
Axle boots ................................................ 8-34
Brake light switches ................................. 8-34
Checking and lubricating the cables ........ 8-35
Checking and lubricating the front and
rear brake levers .................................... 8-36
Checking and lubricating the brake
pedal ...................................................... 8-36
Checking the wheel hub bearings ............ 8-37
Lubricating the steering shaft ................... 8-37
Battery ...................................................... 8-38
Replacing a fuse ...................................... 8-40
Replacing a headlight bulb ....................... 8-42
Adjusting a headlight beam ...................... 8-43
Replacing the tail/brake light bulb ............ 8-44
Removing a wheel .................................... 8-44
Installing a wheel ...................................... 8-44
Troubleshooting ....................................... 8-46
Troubleshooting chart .............................. 8-47
CLEANING AND STORAGE .......................... 9-1
Cleaning ..................................................... 9-1
Storage ....................................................... 9-2SPECIFICATIONS .......................................10-1
CONSUMER INFORMATION.......................11-1
Identification numbers ...............................11-1
U1AB60E0.book Page 3 Wednesday, April 29, 2009 10:19 AM

3-1
3
EBU17680
DESCRIPTION
EBU17690Left view
EBU17700Right view
1. Fuel cock
2. Throttle stop screw
3. Air filter case
4. Fuses
5. Battery
6. Tail/brake light
7. Recoil starter
8. Engine oil filler cap
9. Oil filter cartridge
10.V-belt cooling duct check hose
3
4,5 1
26
10978
1. Rear shock absorber assembly spring preload adjusting
ring
2. Spark arrester
3. Storage compartment and tool kit
4. Spark plug
5. Front shock absorber assembly spring preload adjusting
ring
6. Rear brake light switch
7. Brake pedal
8. V-belt case drain plug12 3 4 5
6 7 8
U1AB60E0.book Page 1 Wednesday, April 29, 2009 10:19 AM

3-2
3
EBU17712Controls and instruments
TIPThe ATV you have purchased may differ slightly
from the figures shown in this manual.
1. Rear brake lever
2. Handlebar switches
3. Starter (choke)
4. Parking brake lock plate
5. Horn switch
6. Drive select lever
7. Speedometer
8. Main switch
9. Fuel tank cap
10.On-Command four-wheel-drive switch
11.Throttle lever
12.Front brake leverU1AB60E0.book Page 2 Wednesday, April 29, 2009 10:19 AM

4-1
4
EBU17733
INSTRUMENT AND CONTROL FUNCTIONS
EBU17770Main switch The positions of the main switch are as follows:
ON
All electrical systems are supplied with power. The
headlights, meter lighting and taillight come on
when the light switch is on, and the engine can be
started. The key cannot be removed.
OFF
All electrical systems are off. The key can be re-
moved.
1. Main switch
U1AB60E0.book Page 1 Wednesday, April 29, 2009 10:19 AM

4-2
4
EBU17814Indicator lights and warning light EBU17850Reverse indicator light “REVERSE”
This indicator light comes on when the transmis-
sion is in the reverse position.EBU17870Neutral indicator light “NEUTRAL”
This indicator light comes on when the transmis-
sion is in the neutral position.
EBU26931Oil temperature warning light“”
This warning light comes on when the engine over-
heats. When this occurs, stop the engine as soon
as it is safe to do so, and allow it to cool.
The electrical circuit of the warning light can be
checked by turning the key to “ON”, with the engine
stop switch set to“”, and then pushing the start
switch.
If the warning light does not come on while the start
switch is being pushed, then go off after the start
switch is released, have a Yamaha dealer check
the electrical circuit.
If the warning light stays on, allow the engine to
cool. If the warning light stays on when the engine
is cool, have a Yamaha dealer check the electrical
circuit.NOTICEECB00010
The engine may overheat if the ATV is over-
loaded. In this case, reduce the load to spec-
ification.
Start the engine after making sure that the
warning light is out. Continuous use while
the warning light is on may cause damage to
the engine.
1. Reverse indicator light “REVERSE”
2. Neutral indicator light “NEUTRAL”
3. On-Command four-wheel-drive indicator light“”
4. Oil temperature warning light“”U1AB60E0.book Page 2 Wednesday, April 29, 2009 10:19 AM

4-3
4
EBU17952On-Command four-wheel-drive indicator
light“”
This indicator light comes on when the On-Com-
mand four-wheel-drive switch is set to the “4WD”
position.TIPDue to the synchronizing mechanism in the differ-
ential gear case, the light may not come on until
the ATV starts moving.EBU18021Speedometer The speedometer shows the riding speed. This
speedometer is equipped with an odometer and a
tripmeter. The tripmeter can be reset to zero with
the reset knob. Use the tripmeter to estimate how
far you can ride on a tank of fuel before going to re-
serve. This information will enable you to plan fuel
stops in the future.
1. Reset knob
2. Speedometer
3. Odometer
4. Tripmeter
U1AB60E0.book Page 3 Wednesday, April 29, 2009 10:19 AM

4-4
4
EBU18061Handlebar switches EBU18080Engine stop switch“/”
Set this switch to“” before starting the engine.
The engine stop switch controls the ignition and
stops the engine when it is running. Use this switch
to stop the engine in an emergency situation. The
engine will not start or run when this switch is set
to“”.
EBU18101Start switch“”
Push this switch to crank the engine with the start-
er. See the starting instructions on page 6-1 prior
to starting the engine.EBU18161Light switch“//OFF”
Set this switch to“” to turn on the low beams,
the taillight and the meter lighting. Set the switch
to“” to turn on the high beams, the taillight and
the meter lighting. Set the switch to “OFF” to turn
off all the lights.NOTICEECB00041Do not use the headlights with the engine
turned off for an extended period of time, oth-
erwise the battery may discharge to the point
that the starter motor will not operate properly.
If this should happen, remove the battery and
recharge it. See page 8-38 for battery charging
information.EBU18170Horn switch“”
Press the switch to sound the horn.
1. Light switch“//OFF”
2. Engine stop switch“/”
3. Start switch“”
4. Horn switch“”U1AB60E0.book Page 4 Wednesday, April 29, 2009 10:19 AM

4-5
4
EBU28432On-Command four-wheel-drive switch
“2WD”/“4WD”
WARNING
EWB00163Always stop the ATV before changing from
two-wheel drive to four-wheel drive and vice
versa. The ATV handles differently in two-
wheel drive than in four-wheel drive in some
circumstances. Changing from two-wheel
drive to four-wheel drive or vice versa while
moving may cause the ATV to unexpectedly
handle differently. This could distract the oper-
ator and increase the risk of losing control and
of causing an accident.This ATV is equipped with a switch to change from
two-wheel drive to four-wheel drive and vice versa.
Select the appropriate drive according to the ter-
rain and the conditions.
“2WD” (two-wheel drive): Power is supplied to
the rear wheels.
“4WD” (four-wheel drive): Power is supplied to
the rear and front wheels.To change from two-wheel drive to four-wheel
drive, stop the ATV and push the switch in to the
“4WD” position. The four-wheel-drive indicator
light“” comes on.
To change from four-wheel drive to two-wheel
drive, stop the ATV and push the switch in to the
“2WD” position.
EBU18282Throttle lever Once the engine is running, pushing the throttle le-
ver will increase the engine speed.1. On-Command four-wheel-drive switch “2WD”/“4WD”
U1AB60E0.book Page 5 Wednesday, April 29, 2009 10:19 AM

4-9
4

Always be sure you have released the park-
ing brake before you begin to ride. The brake
could overheat if you ride the ATV without re-
leasing the parking brake. You could lose
braking performance which could cause an
accident. You could also wear out the brakes
prematurely.EBU18581Drive select lever The drive select lever is used to shift your ATV into
the forward, neutral and reverse positions. See the
“Operating the drive select lever and driving in re-
verse” section on page 6-3 for the drive select lever
operation.
EBU18670Recoil starter Firmly grasp the handle and pull slightly until en-
gagement can be felt. Then pull forcefully, being
careful not to pull the rope all the way out.1. Drive select lever
U1AB60E0.book Page 9 Wednesday, April 29, 2009 10:19 AM