light YAMAHA MAJESTY 125 2007 Owner's Manual

EAUS1130
Replacing the tail/brake light
bulb or a rear turn signal
light bulb
Tail/brake light bulb
1. Screw
2. Tail/brake light lens
3. Bulb
1. Remove the tail/brake light lens
by removing the screw.
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw.Rear turn signal light bulb
1. Turn signal light lens
2. Screw
3. Turn signal light bulb lens
4. Bulb
1. Remove the tail/brake light bulb
lens by removing the screw.
2. Remove the left or right turn sig-
nal light bulb lens by pulling it
backwards.
3. Remove the bulb cap by remo-
ving the screw.
4. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
5. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
6. Install the bulb cap by installing
the screw7. Install the turn signal light bulb
lens.
8. Install the tail/brake light bulb
lens by installing the screw.
ECA10680
CAUTION:
Do not overtighten the screws,
otherwise the lens may break.
1 2
3 4
1 2 3
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-30
5D8-F8199-E0.qxd 1/6/07 16:20 Página 65

EAUM1460
Replacing the license plate
light bulb
1. Screw
2. License plate light cover
3. Socket
1. Remove the license plate light
cover by removing the screw.
2. Remove the socket (together
with the bulb) by pulling it out.
3. Remove the defective bulb by
pulling it out.
4. Insert a new bulb into the socket.
5. Install the socket (together with
the bulb) by pushing it in.
6. Install the license plate light
cover by installing the screw.
EAUS1260
Replacing the auxiliary light
bulb
1. Auxiliary light bulb socket
If the auxiliary light bulb burns out,
replace it as follows.
1. Remove panel A . (See page 6-
6.).
2. Remove the socket (together
with the bulb) by pulling it out.
3. Remove the defective bulb by
pulling it out.
4. Insert a new bulb into the socket.
5. Install the socket (together with
the bulb) by pushing it in.
6. Install the panel A.
EAU25880
Troubleshooting
Although Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition sys-
tems, for example, can cause poor
starting and loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your scooter
require any repair, take it to a Yamaha
dealer, whose skilled technicians
have the necessary tools, experience,
and know-how to service the scooter
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
12 3
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-31
5D8-F8199-E0.qxd 1/6/07 16:20 Página 66

thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
Do not use high-pressure was-
hers or steam-jet cleaners sin-
ce they cause water seepage
and deterioration in the follo-
wing areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or scrat-
ching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not lea-
ve any marks. If the windshield
is scratched, use a quality
plastic polishing compound
after washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas. Stub-
born dirt and insects will come off
more easily if the area is covered with
a wet cloth for a few minutes before
cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.
NOTE:
Salt sprayed on roads in the winter
may remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the
engine has cooled down.
ECA10790
CAUTION:
Do not use warm water since it
increases the corrosive action of
the salt.
2. Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, surfa-
ces to prevent corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally indu-
ced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, inclu-
ding chrome- and nickel-plated,
surfaces.
4. Use spray oil as a universal clea-
ner to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
7
SCOOTER CARE AND STORAGE
7-2
5D8-F8199-E0.qxd 1/6/07 16:20 Página 70

Operation
Centrifugal automatic type
ChassisFrame type
Steel tube underbone
Caster angle
28 º
Trail
104.0 mm (4.09 in)
Front tireType
Tubeless
Size
120/70 - 12 51L
Manufacturer/model
CONTINENTAL / ZIPPY 1
PIRELLI / SL26
MICHELIN / BOPPER
Rear tireType
Tubeless
Size
130/70 - 12 56L
Manufacturer/model
CONTINENTAL / ZIPPY 1
PIRELLI / SL26
MICHELIN / BOPPER
LoadingMaximum load
177 kg (390.29 lb)
Load is total weight of the equipement, dri-
ver, passenger and accessories
Tire air pressure (measured on cold
tires)
Loading condition
0–90 kg (0–198 lb)
Front
190 kPa (27 psi) (1.9 kgf/cm
2)
Rear
220 kPa (31 psi) (2.2 kgf/cm
2)
Loading condition
90 kg (198 lb)–Maximum load
Front
190 kPa (27 psi) (1.9 kgf/cm
2)
Rear
240 kPa (34 psi) (2.4 kgf/cm
2)
Front wheelWheel type
Aluminium wheel
Rim size
12 x MT3.50
Rear wheelWheel type
Aluminium wheel
Rim size
12 x MT3.50
Front brakeType
Single disc brake
Operation
Right hand operation
Recommended fluid
DOT 4
Rear brakeType
Single disc brakeOperation
Left hand operation
Recommended fluid
DOT 4
Front suspensionType
Telescopic fork
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
90 mm (3.54 in)
Rear suspensionType
Unit swing
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
90 mm (3.54 in)
Electrical systemIgnition system
CDI
Charging system
AC magneto
BatteryManufacturer/model
GS / CB7L-B2
Voltage, capacity
12 V, 8.0 Ah
Bulb voltage, wattage x quantityHeadlight
12 V, 55.0 W x 2
Auxiliary light
12 V, 5.0 W x 2
Tail/brake light
8
SPECIFICATIONS
8-2
5D8-F8199-E0.qxd 1/6/07 16:20 Página 74

12 V, 21.0 W / 5.0 W x 2
Front turn signal light
12 V, 21.0 W x 2
Rear turn signal light
12 V, 10.0 W x 2
License plate light
12 V, 5.0 W x 1
Meter lighting
12 V, 1.2 W x 2
High beam Indicator light
12 V, 1.2 W x 1
Turn signal indicator light
12 V, 1.2 W x 2
Coolant temperature warning light
12 V, 1.2 W x 1
FusesMain fuse
20 A
Radiator fan fuse
4 A
Reserve fuse
20 A
Reserve fuse
4 A
8
SPECIFICATIONS
8-3
5D8-F8199-E0.qxd 1/6/07 16:20 Página 75

AAcceleration and deceleration ...................5-2
Air filter and V-belt case air filter
elements ................................................6-14
Anti-theft alarm (optional) ..........................3-5
Auxiliary light bulb, replacing ...................6-31
BBattery......................................................6-24
Brake fluid level, checking .......................6-20
Brake fluid, changing ...............................6-21
Brake lever, front ........................................3-6
Brake lever, rear .........................................3-6
Brake levers, lubricating ..........................6-22
Braking .......................................................5-2
CCables, checking and lubricating ............6-21
Carburetor,adjusting.................................6-15
Care............................................................7-1
Catalytic converter .....................................3-9
Caution, matte color ..................................7-1
Centerstand and sidestand, checking
and lubricating .......................................6-22
Clock ..........................................................3-4
Coolant.....................................................6-12
Coolant temperature warning light ............3-2
DDimmer switch ...........................................3-5
EEngine break-in ..........................................5-3
Engine oil ...................................................6-9
FFinal transmission oil ...............................6-11
Front and rear brake lever free play.........6-19
Front and rear brake pads, checking ......6-19Front fork, checking .................................6-23
Front Storage compartment ....................3-10
Fuel ............................................................3-8
Fuel consumption, tips for reducing ..........5-3
Fuel tank breather/overflow hose ..............3-9
Fuel tank cap .............................................3-7
Fuses, replacing .......................................6-26
HHandlebar switches ...................................3-5
Hazard switch ............................................3-6
Headlight bulb, replacing .........................6-27
High beam indicator light...........................3-2
Horn switch ................................................3-5
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ..................3-13
Indicator lights ...........................................3-2
KKey identification number ..........................9-1
LLicense plate light bulb, replacing ...........6-31
MMain switch/steering lock ..........................3-1
Model label ................................................9-2
OOil change indicator ...................................3-2
PPanels, removing and installing .................6-6
Parking .......................................................5-4
Part locations .............................................2-1
Periodic maintenance and lubrication
chart .........................................................6-3
Pre-operation check list .............................4-2
SSafe-riding points.......................................1-4
Safety information ......................................1-1
Seat ............................................................3-9
Shock absorber assemblies, adjusting....3-12
Sidestand .................................................3-12
Spark plug, checking .................................6-7
Specifications.............................................8-1
Speedometer unit ......................................3-2
Start switch ................................................3-5
Starting a cold engine ................................5-1
Starting off .................................................5-2
Steering, checking ...................................6-23
Storage.......................................................7-3
Storage compartment ..............................3-11
TTail/brake light bulb or rear turn signal
light bulb, replacing ...............................6-30
Throttle cable free play, adjusting ............6-15
Tires .........................................................6-16
Tool kit ........................................................6-1
Troubleshooting .......................................6-31
Troubleshooting charts ............................6-32
Turn signal indicator lights .........................3-2
Turn signal light bulb (front), replacing ....6-29
Turn signal switch ......................................3-5
VValve clearance ........................................6-16
Vehicle identification number .....................9-1
WWheel bearings, checking........................6-24
Wheels .....................................................6-18
INDEX
5D8-F8199-E0.qxd 1/6/07 16:20 Página 78