ABS YAMAHA MT-03 2020 User Guide

Periodic maintenance and adjustment
6-31
6
EAU62776
Replacing the fuses
The main fuse is located under the
passenger seat. The fuse box, which
contains the fuses for the individual cir-
cuits, is located behind the center pan-
el.
To access the main fuse, proceed as
follows.
1. Remove the passenger seat. (See
page 3-17.)
2. Remove the tray by removing the
quick fasteners.
3. Pull back the starter relay cover.
4. Disconnect the starter relay cou-
pler by pressing from both sides.5. Connect the starter relay coupler,
and then slide the cover to its orig-
inal position.
6. Place the tray in its original posi-
tion, and then install the quick fas-
teners.
7. Install the passenger seat.
TIP
To access the fuse box, remove the
center cover. (See page 3-17.)
1. Quick fastener
2. Tray
1. Starter relay cover
2. Starter relay coupler
3. Main fuse
4. Spare main fuse
2
1
1
2
3
4
1. Fuse box
1. Ignition fuse
2. Signaling system fuse
3. ABS control unit fuse
4. Headlight fuse
5. Backup fuse (for clock)
6. Radiator fan motor fuse
7. Spare fuse
1
71
2
3
5
6
4
UB6WE0E0.book Page 31 Friday, March 27, 2020 11:37 AM

Periodic maintenance and adjustment
6-32
6
If a fuse is blown, replace it as follows.
1. Turn the main switch off and turn
off the electrical circuit in ques-
tion.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage. WARNING! Do not
use a fuse of a higher amperage
rating than recommended to
avoid causing extensive dam-
age to the electrical system and
possibly a fire.
[EWA15132]
3. Turn the main switch on and turn
on the electrical circuit in question
to check if the device operates.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
1. Fuse box 2
1. Spare fuse
2. ABS solenoid fuse
3. ABS motor fuse
1
123
Specified fuses:
Main fuse:
30.0 A
Headlight fuse:
7.5 A
Signaling system fuse:
15.0 A
Ignition fuse:
15.0 A
Radiator fan motor fuse:
7.5 A
ABS motor fuse:
30.0 A
ABS solenoid fuse:
15.0 A
ABS control unit fuse:
7.5 A
Backup fuse:
7.5 A
UB6WE0E0.book Page 32 Friday, March 27, 2020 11:37 AM

Motorcycle care and storage
7-2
7 harsh chemicals, including
strong acidic wheel cleaners,
especially on spoke or magne-
sium wheels.
harsh chemicals, abrasive
cleaning compounds, or wax on
matte-finished parts. Brushes
can scratch and damage the
matte-finish, use soft sponge or
towel only.
towels, sponges, or brushes
contaminated with abrasive
cleaning products or strong
chemicals such as, solvents,
gasoline, rust removers, brake
fluid, or antifreeze, etc.
Before washing
1. Park the vehicle out of direct sun-
light and allow it to cool. This will
help avoid water spots.
2. Make sure all caps, covers, elec-
trical couplers and connectors are
tightly installed.
3. Cover the muffler end with a plas-
tic bag and a strong rubber band.
4. Pre-soak stubborn stains like in-
sects or bird droppings with a wet
towel for a few minutes.
5. Remove road grime and oil stains
with a quality degreasing agent
and a plastic-bristle brush or
sponge. NOTICE: Do not use
degreasing agent on areas re-
quiring lubrication such as
seals, gaskets, and wheel axles.
Follow product instructions.
[ECA26290]
Washing
1. Rinse off any degreaser and spray
down the vehicle with a garden
hose. Use only enough pressure
to do the job. Avoid spraying wa-
ter directly into the muffler, instru-
ment panel, air inlet, or other inner
areas such as underseat storage
compartments.
2. Wash the vehicle with a quality au-
tomotive-type detergent mixed
with cool water and a soft, clean
towel or sponge. Use an old tooth-
brush or plastic-bristle brush for
hard-to-reach places. NOTICE:
Use cold water if the vehicle has
been exposed to salt. Warm wa-
ter will increase salt’s corrosive
properties.
[ECA26301]
3. For windshield-equipped vehicles:
Clean the windshield with a soft
towel or sponge dampened with
water and a pH neutral detergent.
If necessary, use a high-quality
windshield cleaner or polish for
motorcycles. NOTICE: Never use
any strong chemicals to clean
the windshield. Additionally,
some cleaning compounds for
plastic may scratch the wind-
shield, so be sure to test all
cleaning products before gen-
eral application.
[ECA26310]
4. Rinse off thoroughly with clean
water. Be sure to remove all deter-
gent residues, as they can be
harmful to plastic parts.
After washing
1. Dry the vehicle with a chamois or
absorbent towel, preferably mi-
crofiber terrycloth.
UB6WE0E0.book Page 2 Friday, March 27, 2020 11:37 AM

10-1
10
Index
A
ABS ...................................................... 3-13
ABS warning light ................................... 3-3
Air filter element and check hose,
replacing and cleaning ....................... 6-13
B
Battery .................................................. 6-29
Brake and clutch levers,
checking and lubricating .................... 6-26
Brake and shift pedals,
checking and lubricating .................... 6-26
Brake fluid, changing ........................... 6-22
Brake fluid level, checking ................... 6-21
Brake lever ........................................... 3-12
Brake lever free play, checking ............ 6-19
Brake light switches ............................. 6-20
Brake pedal .......................................... 3-13
C
Cables, checking and lubricating ......... 6-25
Canister .................................................. 6-8
Care ........................................................ 7-1
Catalytic converter ............................... 3-17
Clock ...................................................... 3-5
Clutch lever .......................................... 3-11
Clutch lever free play, adjusting ........... 6-18
Coolant ................................................. 6-12
Coolant temperature meter .................... 3-5
D
Data recording, vehicle .......................... 9-2
Diagnostic connector ............................. 9-2
Dimmer switch ..................................... 3-10
Display units, switching.......................... 3-4
Drive chain, cleaning and lubricating ... 6-24
Drive chain slack .................................. 6-23
E
Engine break-in ...................................... 5-1
Engine oil and oil filter cartridge ............. 6-8
Engine overheating............................... 6-37
Engine serial number.............................. 9-1
Engine trouble warning light................... 3-3
F
Front and rear brake pads, checking ... 6-20
Front fork, checking ............................. 6-28
Fuel....................................................... 3-15
Fuel consumption, tips for reducing ...... 5-4
Fuel meter .............................................. 3-4
Fuel tank cap........................................ 3-14
Fuel tank overflow hose ....................... 3-16
Fuses, replacing ................................... 6-31
H
Handlebar switches .............................. 3-10
Hazard switch ....................................... 3-10
Helmet holders...................................... 3-19
High beam indicator light........................ 3-2
Horn switch........................................... 3-10
I
Identification numbers ............................ 9-1
Ignition circuit cut-off system ............... 3-22
Indicator lights and warning lights .......... 3-2
L
License plate light bulb, replacing ........ 6-33
Luggage strap holders .......................... 3-21
M
Main switch/steering lock ....................... 3-1
Maintenance and lubrication, periodic ... 6-4
Maintenance, emission control
system .................................................. 6-3
Matte color, caution ................................ 7-1
Model label ............................................. 9-1
Multi-function display ............................. 3-6
Multi-function meter unit ........................ 3-4
N
Neutral indicator light.............................. 3-2
O
Oil pressure warning light ....................... 3-2
P
Parking .................................................... 5-5
Part locations .......................................... 2-1
Pass switch........................................... 3-10
S
Safety information................................... 1-1
Seats ..................................................... 3-17
Shift indicator light .................................. 3-3
Shift indicator light control mode ........... 3-8
Shifting .................................................... 5-3
Shift pedal............................................. 3-12
Shock absorber assembly, adjusting ... 3-20
Sidestand .............................................. 3-22
Sidestand, checking and lubricating .... 6-27
Spark plugs, checking ............................ 6-7
Specifications ......................................... 8-1
Speedometer .......................................... 3-4
Start/Engine stop switch ...................... 3-10
Starting the engine.................................. 5-2
Steering, checking ................................ 6-28
Storage ................................................... 7-4
Storage compartment ........................... 3-20
Supporting the motorcycle ................... 6-34
Swingarm pivots, lubricating ................ 6-27
UB6WE0E0.book Page 1 Friday, March 27, 2020 11:37 AM