light YAMAHA TZR50 2003 User Guide

EAU18781
Removing and installing
cowlings
1. Cowling A
2. Cowling B
The cowlings shown need to be
removed to perform some of the
maintenance jobs described in this
chapter. Refer to this section each
time a cowling needs to be removed
and installed.
EAU18880
Cowling A
1. Screws (x 7 Right side)
1. Screws (x 6 Left side)
To remove the cowling
1. Remove the cowling screws.
2. Push the cowling in lightly, and
then pull it back as shown.
ECA11200
CAUTION
Take care not to damage the tabs
on the cowling when removing and
or installing it.
To install the cowling
1. Insert the tabs on the cowling
into the slots as shown, and then
push the cowling in until it snaps
into place.
2. Install the cowling screws.
EAU18790
Cowling B
1. Screws (x 5 Rechterkant)
1. Screws (x 7 Linkerkant)
To remove the cowling
Remove the screws, and then take
the cowling off.
T
o install the cowling
Place the cowling in the original posi-
tion, and then install the screws.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-5
12
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 37

EAU19620
Checking the spark plug
1. Spark plug
The spark plug is an important engine
component, which should be chec-
ked periodically, preferably by a
Yamaha dealer. Since heat and depo-
sits will cause any spark plug to
slowly erode, it should be removed
and checked in accordance with the
periodic maintenance and lubrication
chart. In addition, the condition of the
spark plug can reveal the condition of
the engine.
The porcelain insulator around the
center electrode of the spark plug
should be a medium-to-light tan (the
ideal color when the vehicle is riddennormally). If the spark plug shows a
distinctly different color, the engine
could be defective. Do not attempt to
diagnose such problems yourself.
Instead, have a Yamaha dealer check
the vehicle.
If the spark plug shows signs of elec-
trode erosion and excessive carbon
or other deposits, it should be repla-
ced.
Before installing a spark plug, the
spark plug gap should be measured
with a wire thickness gauge and, if
necessary, adjusted to specification.
Clean the surface of the spark plug
gasket and its mating surface, and
then wipe off any grime from the
spark plug threads.
NOTE:
If a torque wrench is not available
when installing a spark plug, a good
estimate of the correct torque is
1/4~1/2 turn past finger tight. Howe-
ver, the spark plug should be tighte-
ned to the specified torque as soon
as possible.
EAUM1270
Transmission oil
1. Oil level check bolt
2. Oil drain bolt
3. Oil filler cap
Tightening torque:
Spark plug:
20 Nm (2,0 m•kgf)
Spark plug gap:
0,6 ~ 0,7 mm (0,023~0,027 in)
Specified spark plug:
BR9ES (NGK)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-6
1
3
1
2
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 38

The transmission oil level should be
checked before each ride. In addition,
the oil must be changed at the inter-
vals specified in the periodic mainte-
nance and lubrication chart.
To check the transmission oil level
1. Place the vehicle on a level surfa-
ce and hold it in an upright posi-
tion.
NOTE:
Make sure that the vehicle is positio-
ned straight up when checking the oil
level. A slight tilt to the side can result
in a false reading.
2. Remove the oil check bolt, and
then check the oil level.
NOTE:
The oil should be at the brim of the
check hole.
3. If the oil is below the brim of the
check hole, remove the oil filler
cap, add sufficient oil of the
recommended type to raise it to
the correct level, and then install
the oil filler cap.
4. Install the oil check bolt, and then
tighten it to the specified torque.
To change the transmission oil
1. Place an oil pan under the trans-
mission oil case to collect the used
oil.
2. Remove the drain bolt and the oil
check bolt to drain the oil.
3. Install the drain bolt and the
check bolt, and then tighten them to
the specified torque.4. Remove the oil filler cap, add the
specified amount of the recom-
mended transmission oil, and
then install and tighten the oil
filler cap.
ECAM1020
CAUTION
Make sure that no foreign material
enters the transmission case.
5. Start the engine and let it idle for
several minutes while checking
the transmission oil case for oil
leakage. If oil is leaking, imme-
diately turn the engine off and
check for the cause.
Recommended transmission oil:
See page 8-1.
Oil change quantity:
0,75 L (0,65 imp.qt)
Tightening torque:
Transmission oil drain bolt:
17 Nm (1,7 m•kgf)
Oil check bolt:
3 Nm (0,3 m•kgf)
Tightening torque:
Oil check bolt:
3 Nm (0,3 m•kgf)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-7
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 39

EAU20170
To check the coolant level
1. Place the vehicle on a level surfa-
ce and hold it in an upright posi-
tion.
NOTE:
The coolant level must be chec-
ked on a cold engine since the
level varies with engine tempera-
ture.
Make sure that the vehicle is
positioned straight up when
checking the coolant level. A
slight tilt to the side can result in
a false reading.
1. Panel
2. Remove panel (1). (See page 6-8.)
3. Check the coolant level in the
coolant reservoir.
NOTE:
The coolant should be between the
minimum and maximum level marks.
4. If the coolant is at or below the
minimum level mark, open the
reservoir cap, add coolant to the
maximum level mark, and then
close the reservoir cap.
ECA10470
CAUTION
If coolant is not available, use
distilled water or soft tap water
instead. Do not use hard water
or salt water since it is harmful
to the engine.
If water has been used instead
of coolant, replace it with coo-
lant as soon as possible, other-
wise the engine may not be
sufficiently cooled and the coo-
ling system will not be protec-
ted against frost and corrosion.
If water has been added to the
coolant, have a Yamaha dealer
check the antifreeze content of
the coolant as soon as possible,
otherwise the effectiveness of
the coolant will be reduced.
EWA10380
s s
WARNING
Never attempt to remove the radia-
tor cap when the engine is hot.
5. Install the panel.
Coolant reservoir capacity:
0,45 L (0.39 Imp.qt)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-8
MIN MAX
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 40

adjusting nut in direction (b).
6. Tighten the locknut at the clutch
lever and the crankcase.
EAU22220
Adjusting the brake pedal
position and free play
1. Position adjusting bolt
2. Brake pedal position
EWA10670
s s
WARNING
It is advisable to have a Yamaha
dealer make these adjustments.
Brake pedal position
The top of the brake pedal should be
aligned with the top of the footrest as
shown. Periodically check the brake
pedal position and, if necessary,
adjust it as follows.1. Loosen the locknut at the brake
pedal.
2. To raise the brake pedal, turn the
adjusting bolt in direction (a). To
lower the brake pedal, turn the
adjusting bolt in direction (b).
3. Tighten the locknut.
EWA11230
s s
WARNING
After adjusting the brake pedal
position, the brake pedal free play
must be adjusted.
Brake pedal free play
1. Free play
The brake pedal free play should
measure 10~15 mm (0,39~59 in) at
the brake pedal end. Periodically
check the brake pedal free play and, if
necessary, adjust it as follows.To increase the brake pedal free play,
turn the adjusting nut at the brake rod
in direction (a). To decrease the brake
pedal free play, turn the adjusting nut
in direction (b).
EWA10660
s s
WARNING
After adjusting the brake pedal free
play, check the operation of the
brake light.
EAU22270
Adjusting the rear brake light
switch
1. Switch
2. Lock nut
The rear brake light switch, which is
activated by the brake pedal, is pro-
perly adjusted when the brake light
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-13
21
1
1
2a
b
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 45

comes on just before braking takes
effect. If necessary, adjust the brake
light switch as follows.
Turn the adjusting nut while holding
the rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction (a).
To make the brake light come on later,
turn the adjusting nut in direction (b).
EAU22420
Front brake pads
Each front brake pad is provided with
a wear indicator groove, which allows
you to check the brake pad wear wit-
hout having to disassemble the brake.
To check the brake pad wear, check
the wear indicator groove. If a brake
pad has worn to the point that thewear indicator groove has almost
disappeared, have a Yamaha dealer
replace the brake pads as a set.
EAU22480
Rear brake pads
Each rear brake pad is provided with
a wear indicator groove, which allows
you to check the brake pad wear wit-
hout having to disassemble the brake.
Check the brake pad wear as follows.
1. Remove the brake caliper bolt,
and then tilt the caliper forward to
inspect the wear indicator groo-
ve. If a brake pad has worn to the
point that the wear indicator gro-
ove has almost disappeared,
have a Yamaha dealer replace
the brake pads as a set.2. Install the brake caliper bolt, and
then tighten it to the specified
torque.
EAU22610
Checking the brake fluid
level
Insufficient brake fluid may allow air
to enter the brake system, possibly
causing it to become ineffective.
Tightening torque:
Brake caliper bolt:
30 Nm (3,0 m•kgf)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-14
FRONT
mín.
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 46

2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
ECA10640
CAUTION
Do not use a fuse of a higher ampe-
rage rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.
3. Turn the key to “ON” and turn on
the electrical circuits to check if the
devices operate.
4. If the fuse immediately blows
again, have a Yamaha dealer check
the electrical system.
EAU23800
Replacing the headlight bulb
This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.
1. Remove the headlight bulb cover,
and then disconnect the head-
light lead connectors.
2. Unhook the headlight bulb hol-der, and then remove the defecti-
ve bulb.
EWA10790
s s
WARNING
Headlight bulbs get very hot. The-
refore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.
3. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
ECA10660
CAUTION
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the
bulb, and the bulb life will be adver-
sely affected. Thoroughly clean off
any dirt and fingerprints on the
headlight bulb using a cloth mois-
tened with alcohol or thinner.
4. Connect the headlight lead con-
nectors, and then install the bulb
cover.
5. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24281
Replacing a turn signal light
bulb or the tail/brake light
bulb
1. Remove the lens by removing the
screws.
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
Specified fuse:
10 A
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-21
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 53

4. Install the lens by installing the
screws.
ECA10680
CAUTION
Do not overtighten the screws,
otherwise the lens may break.
EAUM1460
Replacing the license plate
light bulb
1. Auxiliary light
1. Remove the license plate light
cover by removing the screw.
2. Remove the socket (together
with the bulb) by pulling it out.
3. Remove the defective bulb by
pulling it out.
4. Insert a new bulb into the socket.
5. Install the socket (together with
the bulb) by pushing it in.
6. Install the license plate light
cover by installing the screw.
EAU24350
Supporting the motorcycle
Since this model is not equipped with
a centerstand, follow these precau-
tions when removing the front and
rear wheel or performing other main-
tenance requiring the motorcycle to
stand upright. Check that the
motorcycle is in a stable and level
position before starting any mainte-
nance. A strong wooden box can be
placed under the engine for added
stability.
To service the front wheel
1. Stabilize the rear of the motorcy-
cle by using a motorcycle stand
or, if an additional motorcycle
stand is not available, by placing
a jack under the frame in front of
the rear wheel.
2. Raise the front wheel off the
ground by using a motorcycle
stand.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-22
1
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 54

EAU26000
Care
While the open design of a motorcy-
cle reveals the attractiveness of the
technology, it also makes it more vul-
nerable. Rust and corrosion can
develop even if high-quality compo-
nents are used. A rusty exhaust pipe
may go unnoticed on a car, however,
it detracts from the overall appearan-
ce of a motorcycle. Frequent and pro-
per care does not only comply with
the terms of the warranty, but it will
also keep your motorcycle looking
good, extend its life and optimize its
performance.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and
covers as well as all electrical
couplers and connectors, inclu-
ding the spark plug cap, are
tightly installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such pro-ducts onto seals, gaskets, sproc-
kets, the drive chain and wheel
axles. Always rinse the dirt and
degreaser off with water.
Cleaning
ECA10770
CAUTION
Avoid using strong acidic whe-
el cleaners, especially on spo-
ked wheels. If such products
are used on hard-to-remove
dirt, do not leave the cleaner on
the affected area any longer
than instructed. Also, tho-
roughly rinse the area off with
water, immediately dry it, and
then apply a corrosion protec-
tion spray.
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or spon-
ge with mild detergent and
water to clean plastic.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasivecleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
Do not use high-pressure was-
hers or steam-jet cleaners sin-
ce they cause water seepage
and deterioration in the follo-
wing areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or scrat-
ching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not lea-
ve any marks. If the windshield
is scratched, use a quality
plastic polishing compound
after washing.
7
MOTORCYCLE CARE AND STORAGE
7-1
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 58

Size
130/70-17 62H
Manufacturer/model
PIRELLI
Maximum load
195 kg
Tire air pressure (measured on cold
tires)
Loading condition
0-90 kg
Front
180 kPa
Rear
200 kPa
Loading condition
90-180 kg
Front
190 kPa
Rear
230 kPa
Front wheelWheel type
Cast wheel
Rim size
MT 2.75x17”
Rear wheelWheel type
Cast wheel
Rim size
MT 3.50x17”
Front brakeType
Single disc brakeRecommended fluid
DOT 4
Rear brakeType
Single disc brake
Recommended fluid
DOT 4
Front suspensionType
Telescopic fork
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
130.0 mm
Rear suspension
Type
Swingarm
Spring/shock absorber type
Coil-gas spring/oil damper
Wheel travel
102.0 mm
Electrical systemIgnition system
DC. CDI
Charging system
CDI magneto
Model
YT4L-BS
Voltage, capacity
12 V, 3.0 Ah
Bulb type
Incandescence
Bulb voltage, wattage x quantityHeadlight
12 V, 25 W/25.0 W x 2
Tail/brake light
12 V, 5.0 W/21.0 W x 1
Front turn signal light
12 V, 16.0 W
Rear turn signal light
12 V, 10.0 W x 2
Neutral indicator light
LED
Oil level warning light
LED
Turn signal indicator light
LED
Coolant temperature warning light
LED
Main fuse
10.0 A
8
SPECIFICATIONS
8-2
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 63