ECU YAMAHA XENTER 125 2012 Owners Manual

1
2
3
4
5
6
7
8
9
1-3
Q
SAFETY INFORMATION●
Do not run engine in poorly ven-
tilated or partially enclosed areas
such as barns, garages, or car-
ports.
●
Do not run engine outdoors
where engine exhaust can be
drawn into a building through
openings such as windows and
doors.
Loading
Adding accessories or cargo to your
scooter can adversely affect stability
and handling if the weight distribution
of the scooter is changed. To avoid
the possibility of an accident, use ex-
treme caution when adding cargo or
accessories to your scooter. Use extra
care when riding a scooter that has
added cargo or accessories. Here,
along with the information about ac-
cessories below, are some general
guidelines to follow if loading cargo to
your scooter:
The total weight of the operator,
passenger, accessories and cargo
must not exceed the maximum load
limit. Operation of an overloaded
vehicle could cause an accident.
Maximum load:
179 kg (395 lb)When loading within this weight limit,
keep the following in mind:●
Cargo and accessory weight
should be kept as low and close
to the scooter as possible. Se-
curely pack your heaviest items
as close to the center of the ve-
hicle as possible and make sure
to distribute the weight as evenly
as possible on both sides of the
scooter to minimize imbalance or
instability.
●
Shifting weights can create a
sudden imbalance. Make sure
that accessories and cargo are
securely attached to the scooter
before riding. Check accessory
mounts and cargo restraints fre-
quently.
• Properly adjust the suspen-
sion for your load (suspension-
adjustable models only), and
check the condition and pres-
sure of your tires.
• Never attach any large or heavy items to the handlebar,
front fork, or front fender. Such
items can create unstable
handling or a slow steering re-
sponse.
●
This vehicle is not designed to
pull a trailer or to be attached
to a sidecar.
Genuine Yamaha Accessories
Choosing accessories for your vehicle
is an important decision. Genuine
Yamaha accessories, which are avail-
able only from a Yamaha dealer, have
been designed, tested, and approved
by Yamaha for use on your vehicle.
Many companies with no connection
to Yamaha manufacture parts and ac-
cessories or offer other modifications
for Yamaha vehicles. Yamaha is not
in a position to test the products that
these aftermarket companies pro-
duce. Therefore, Yamaha can neither
endorse nor recommend the use of
accessories not sold by Yamaha or
modifications not specifically recom-
mended by Yamaha, even if sold and
installed by a Yamaha dealer.
53B-F8199-E0_CS.indd 1-353B-F8199-E0_CS.indd 1-3
2011/11/01 12:32:082011/11/01 12:32:08
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
1-5
Q
SAFETY INFORMATION
EAU45371
Further safe-riding points●
Make sure to signal clearly when
making turns.
●
Braking can be extremely diffi cult
on a wet road. Avoid hard brak-
ing, because the scooter could
slide. Apply the brakes slowly
when stopping on a wet surface.
●
Slow down as you approach a
corner or turn. Once you have
completed a turn, accelerate
slowly.
●
Be careful when passing parked
cars. A driver might not see you
and open a door in your path.
●
Railroad crossings, streetcar
rails, iron plates on road con-
struction sites, and manhole
covers become extremely slip-
pery when wet. Slow down and
cross them with caution. Keep the
scooter upright, otherwise it could
slide out from under you.
●
The brake pads and linings
could get wet when you wash
the scooter. After washing the
scooter, check the brakes before riding.
●
Always wear a helmet, gloves,
trousers (tapered around the cuff
and ankle so they do not flap),
and a bright colored jacket.
●
Do not carry too much luggage
on the scooter. An overloaded
scooter is unstable. Use a strong
cord to secure any luggage to the
carriers. A loose load will affect
the stability of the scooter and
could divert your attention from
the road. (See page 1-3.) bed, and choke it in a rail to pre-
vent movement.
●
Secure the scooter with tie-downs
or suitable straps that are at-
tached to solid parts of the scoot-
er, such as the frame or upper
front fork triple clamp (and not, for
example, to rubber-mounted han-
dlebars or turn signals, or parts
that could break). Choose the
location for the straps carefully
so the straps will not rub against
painted surfaces during transport.
●
The suspension should be com-
pressed somewhat by the tie-
downs, if possible, so that the
scooter will not bounce exces-
sively during transport.
53B-F8199-E0_CS.indd 1-553B-F8199-E0_CS.indd 1-5
2011/11/01 12:32:082011/11/01 12:32:08
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
3-9
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
is properly closed after lling fuel.
Leaking fuel is a re hazard.
EAU13221
Fuel
1
2
1. Fuel tank fi ller tube
2. Maximum fuel levelMake sure there is suffi cient gasoline
in the tank.
EWA10881
WARNING
Gasoline and gasoline vapors are
extremely ammable. To avoid res
and explosions and to reduce the
risk of injury when refueling, follow
these instructions.
1. Before refueling, turn off the en-
gine and be sure that no one is
sitting on the vehicle. Never re-
fuel while smoking, or while in the
vicinity of sparks, open fl ames, or
other sources of ignition such as
the pilot lights of water heaters
and clothes dryers.
2. Do not overfi ll the fuel tank. When
refueling, be sure to insert the
pump nozzle into the fuel tank fi ll-
er hole. Stop fi lling when the fuel
reaches the bottom of the filler
tube. Because fuel expands when
it heats up, heat from the engine
or the sun can cause fuel to spill
out of the fuel tank.
3. Wipe up any spilled fuel im-
mediately.
NOTICE:
Immedi-
ately wipe off spilled fuel with a
clean, dry, soft cloth, since fuel
may deteriorate painted sur-
faces or plastic parts.[ECA10071]
4. Be sure to securely close the fuel
tank cap.
EWA15151
WARNING
Gasoline is poisonous and can
cause injury or death. Handle
gasoline with care. Never siphon
gasoline by mouth. If you should
swallow some gasoline or inhale a
53B-F8199-E0_CS.indd 3-953B-F8199-E0_CS.indd 3-9
2011/11/01 12:32:082011/11/01 12:32:08
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-23
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23192
Checking and lubricating the
centerstand
1
1. CenterstandThe operation of the centerstand
should be checked before each ride,
and the pivots and metal-to-metal
contact surfaces should be lubricated
if necessary.
EWA11301
WARNING
If the centerstand does not move
up and down smoothly, have a
Yamaha dealer check or repair it.
Otherwise, the centerstand could
contact the ground and distract the
operator, resulting in a possible
loss of control.
EAUT3570
Lubricating the front and rear
brake levers11. Rear brake leverThe pivoting points of the front and
rear brake levers should be lubricated
by a Yamaha dealer at the intervals
specifi ed in the periodic maintenance
and lubrication chart.
EAU23114
Checking and lubricating the
throttle grip and cableThe operation of the throttle grip
should be checked before each ride.
In addition, the cable should be lubri-
cated by a Yamaha dealer at the inter-
vals specified in the periodic mainte-
nance chart.
The throttle cable is equipped with a
rubber cover. Make sure that the cov-
er is securely installed. Even though
the cover is installed correctly, it does
not completely protect the cable from
water entry. Therefore, use care not to
pour water directly onto the cover or
cable when washing the vehicle. If the
cable or cover becomes dirty, wipe
clean with a moist cloth.
53B-F8199-E0_CS.indd 6-2353B-F8199-E0_CS.indd 6-23
2011/11/01 12:32:102011/11/01 12:32:10
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-24
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
ECA10590
NOTICEIf any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.
EAU23272
Checking the front forkThe condition and operation of the
front fork must be checked as follows
at the intervals specifi ed in the period-
ic maintenance and lubrication chart.
To check the condition
Check the inner tubes for scratches,
damage and excessive oil leakage.
To check the operation
1. Place the vehicle on a level sur-
face and hold it in an upright
position. WARNING! To avoid
injury, securely support the ve-
hicle so there is no danger of it
falling over.
[EWA10751]
2. While applying the front brake,
push down hard on the handle-
bars several times to check if the
front fork compresses and re-
bounds smoothly.
Recommended lubricant:
Lithium-soap-based grease
53B-F8199-E0_CS.indd 6-2453B-F8199-E0_CS.indd 6-24
2011/11/01 12:32:102011/11/01 12:32:10
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-25
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAUT3760
Battery
1
1. BatteryThis model is equipped with a VRLA
(Valve Regulated Lead Acid) battery.
There is no need to check the electro-
lyte or to add distilled water. However,
the battery lead connections need to
be checked and, if necessary, tight-
ened.
EWA10760
WARNING
●
Electrolyte is poisonous and
dangerous since it contains
sulfuric acid, which causes se-
vere burns. Avoid any contact
with skin, eyes or clothing and
EAU23291
Checking the wheel bearingsThe front and rear wheel bearings
must be checked at the intervals
specifi ed in the periodic maintenance
and lubrication chart. If there is play in
the wheel hub or if the wheel does not
turn smoothly, have a Yamaha dealer
check the wheel bearings.
EAU45511
Checking the steeringWorn or loose steering bearings may
cause danger. Therefore, the opera-
tion of the steering must be checked
as follows at the intervals specifi ed in
the periodic maintenance and lubrica-
tion chart.
1. Place the vehicle on the cen-
terstand. WARNING! To avoid
injury, securely support the ve-
hicle so there is no danger of it
falling over.
[EWA10751]
2. Hold the lower ends of the front
fork legs and try to move them
forward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steer-
ing.
53B-F8199-E0_CS.indd 6-2553B-F8199-E0_CS.indd 6-25
2011/11/01 12:32:102011/11/01 12:32:10
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-29
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU24181
Tail/brake light
1
1. Tail/brake lightThis model is equipped with an LED-
type tail/brake light.
If the tail/brake light does not come
on, have a Yamaha dealer check it.
EAUT3650
Replacing a front turn signal
light bulbIf a front turn signal light burns out, re-
place it as follows.
1. Remove cowling A. (See page
6-7.)
2. Remove the socket (together with
the bulb) by turning it counter-
clockwise.
1
1. Turn signal light bulb socket
3. Unhook the headlight bulb holder,
and then remove the burnt-out
bulb.
4. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
5. Connect the coupler, and then in-
stall the headlight bulb cover.
6. Install the cowling together with
the headlight unit.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
53B-F8199-E0_CS.indd 6-2953B-F8199-E0_CS.indd 6-29
2011/11/01 12:32:102011/11/01 12:32:10
Process BlackProcess Black