tire size YAMAHA XENTER 150 2012 Owners Manual

1
2
3
4
5
6
7
8
9
1-4
Q
SAFETY INFORMATION
Aftermarket Parts, Accessories,
and Modi cations
While you may fi nd aftermarket prod-
ucts similar in design and quality to
genuine Yamaha accessories, recog-
nize that some aftermarket accesso-
ries or modifications are not suitable
because of potential safety hazards
to you or others. Installing aftermarket
products or having other modifi cations
performed to your vehicle that change
any of the vehicle’s design or opera-
tion characteristics can put you and
others at greater risk of serious injury
or death. You are responsible for inju-
ries related to changes in the vehicle.
Keep the following guidelines in mind,
as well as those provided under
“Loading” when mounting accesso-
ries.●
Never install accessories or carry
cargo that would impair the per-
formance of your scooter. Care-
fully inspect the accessory before
using it to make sure that it does
not in any way reduce ground
clearance or cornering clearance,
limit suspension travel, steering travel or control operation, or ob-
scure lights or refl ectors.
• Accessories fitted to the han-
dlebar or the front fork area can
create instability due to improp-
er weight distribution or aerody-
namic changes. If accessories
are added to the handlebar or
front fork area, they must be
as lightweight as possible and
should be kept to a minimum.
• Bulky or large accessories may
seriously affect the stability of
the scooter due to aerodynamic
effects. Wind may attempt to
lift the scooter, or the scooter
may become unstable in cross
winds. These accessories may
also cause instability when
passing or being passed by
large vehicles.
• Certain accessories can dis-
place the operator from his or
her normal riding position. This
improper position limits the
freedom of movement of the
operator and may limit control
ability, therefore, such acces-sories are not recommended.
●
Use caution when adding electri-
cal accessories. If electrical ac-
cessories exceed the capacity of
the scooter’s electrical system, an
electric failure could result, which
could cause a dangerous loss of
lights or engine power.
Aftermarket Tires and Rims
The tires and rims that came with your
scooter were designed to match the
performance capabilities and to pro-
vide the best combination of handling,
braking, and comfort. Other tires,
rims, sizes, and combinations may not
be appropriate. Refer to page 6-17 for
tire specifications and more informa-
tion on replacing your tires.
Transporting the Scooter
Be sure to observe following instruc-
tions before transporting the scooter
in another vehicle.
●
Remove all loose items from the
scooter.
●
Point the front wheel straight
ahead on the trailer or in the truck
52S-F8199-E0_CS.indd 1-452S-F8199-E0_CS.indd 1-4
2011/11/16 13:06:592011/11/16 13:06:59
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-18
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
necessary professional knowl-
edge and experience.
Tire information
This model is equipped with tubeless
tires.
After extensive tests, only the tires
listed below have been approved for
this model by Yamaha Motor Co., Ltd.Front tire:
Size:
100/80-16M/C 50P
Manufacturer/model:
DURO/DM1157F
Rear tire:
Size:
120/80-16M/C 60P
Manufacturer/model:
DURO/DM1157
EWA10470
WARNING
● Have a Yamaha dealer replace
excessively worn tires. Besides
being illegal, operating the
vehicle with excessively worn
tires decreases riding stability
and can lead to loss of control.● The replacement of all wheel
and brake related parts, includ-
ing the tires, should be left to
a Yamaha dealer, who has the
Tire inspection
1
2
1. Tire tread depth
2. Tire sidewallThe tires must be checked before
each ride. If the center tread depth
reaches the specified limit, if the tire
has a nail or glass fragments in it, or if
the sidewall is cracked, have a Yama-
ha dealer replace the tire immediately.Minimum tire tread depth (front and
rear):
0.8 mm (0.03 in)TIPThe tire tread depth limits may differ
from country to country. Always com-
ply with the local regulations.
52S-F8199-E0_CS.indd 6-1852S-F8199-E0_CS.indd 6-18
2011/11/16 13:07:012011/11/16 13:07:01
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
8-2
SPECIFICATIONS
Caster angle
23.83 degree
Trail
84 mm (3.3 in)Front tireType
Tubeless
Size
100 / 80 - 16M/C 50P
Manufacturer/model
DURO / DM1157FRear tireType
Tubeless
Size
120 / 80 - 16M/C 60P
Manufacturer/model
DURO / DM1157LoadingMaximum load
179 kg (395 lb)Tire air pressure (measured on cold
tires)Loading condition
90 kg (198 lb)
Front
175 kPa (1.75 kgf/cm
2, 25 psi, 1.75 bar)
Rear
200 kPa (2.00 kgf/cm2, 29 psi, 2.00 bar)
Loading condition
90 kg - maximum load
Front
175 kPa (1.75 kgf/cm2, 25 psi, 1.75 bar)Rear
225 kPa (2.25 kgf/cm
2, 33 psi, 2.25 bar)
Front wheelWheel type
Cast wheel
Rim size
J 16M/C x MT2.50Rear wheelWheel type
Cast wheel
Rim size
J 16M/C x MT2.75Front brakeType
Single disc brake
Operation
Right hand operation
Specifi ed brake fl uid
DOT 4Rear brakeType
Drum brake
Operation
Left hand operationFront suspensionType
Telescopic fork
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
100.0 mm (3.94 in)Rear suspensionType
Unit swingSpring/shock absorber type
Coil spring/gas-oil damper
Wheel travel
92.0 mm (3.62 in)
Electrical systemIgnition system
TCI
Charging system
AC magnetoBatteryModel
GT7B-4
Voltage, capacity
12 V, 6.5 AhHeadlightBulb type
Halogen bulbBulb voltage, wattage x quantityHeadlight
12 V, 55 W x 2
Tail/brake light
12V, 0.25 / 1.4W x 1 (LED ASSY)
Front turn signal light
12 V, 10.0 W x 2
Rear turn signal light
12 V, 10.0 W x 2
Auxiliary light
12 V, 5.0 W x 2
License plate light
12 V, 5.0 W x 1
Meter lighting
12V,LED x 6
High beam indicator light
12V,LED x 1
52S-F8199-E0_CS.indd 8-252S-F8199-E0_CS.indd 8-2
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black