lights YAMAHA XT660Z 2013 User Guide

PERIODIC MAINTENANCE AND ADJUSTMENT
6-7
6
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
27 *Lights, signals and • Check operation.
switches• Adjust headlight beam.33 3 3 3 3
EAUM1890
TIP
Replace the air filter element more frequently if you are riding in unusually wet or dusty areas.
Hydraulic brake service
• Regularly check and, if necessary, correct the brake fluid level.
• Every two years replace the internal components of the brake master cylinder, and change the brake fluid.
• Replace the brake hoses every four years and if cracked or damaged.

3. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
EAUB1581
Replacing a headlight bulb
This model is equipped with quartz
bulb headlights. If a headlight bulb
burns out, replace it as follows.
ECA10650
Take care not to damage the follo-
wing parts:
Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it
free from oil, otherwise the
transparency of the glass, the
luminosity of the bulb, and the
bulb life will be adversely affec-
ted. Thoroughly clean off any
dirt and fingerprints on the
headlight bulb using a cloth
moistened with alcohol or thin-
ner.
Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
Do not use a headlight bulb of a
wattage higher than specified.
1. Headlight bulb cover
1. Remove the headlight bulb cover,
and then disconnect the head-
light coupler.
1. Headlight coupler
2. Headlight bulb holder
3. Headlight bulb
NOTICE
Specified fuses:
Main fuse:
30.0 A
Parking lighting fuse:
10.0 A
Signaling system fuse:
10.0 A
Headlight fuse:
20.0 A
Ignition fuse:
10.0 A
Fuel injection system fuse:
10.0 A
Radiator fan fuse:
7.5 A
Backup fuse:
10.0 A
ABS motor fuse (for ABS model):
30.0 A
ABS solenoid fuse (for ABS
model):
20.0 A
ABS control unit fuse (for ABS
model):
5.0 A
PERIODIC MAINTENANCE AND ADJUSTMENT
6-32
6

PERIODIC MAINTENANCE AND ADJUSTMENT
6-34
6
EAU24204
Replacing a turn signal light
bulb
1. Remove the turn signal light lens
by removing the screw.
1. Screw
2. Turn signal light lens
3. Turn signal light bulb
2. Remove the burnt-out bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw. NOTICE: Do not over-
tighten the screw, otherwise
the lens may break.
[ECA11191]EAUM2202
Replacing the license plate
light bulb
1. Remove the socket (together
with the bulb) by pulling it out.
1. License plate light bulb socket
2. License plate light bulb
2. Remove the burnt-out bulb by
pulling it out.
3. Insert a new bulb into the socket.
4. Install the socket (together with
the bulb) by pushing it in.
EAU42652
Replacing an auxiliary light
bulb
This model is equipped with two auxi-
liary lights. If an auxiliary light bulb
burns out, replace it as follows.
1. Remove panel G. (See page 6-8).
2. Remove the auxiliary light socket
(together with the bulb) by pulling
it out.
1. Auxiliary light bulb socket
2. Auxiliary light bulb
3. Remove the burnt-out bulb by
pulling it out.
4. Insert a new bulb into the socket.

area, including pilot lights from
water heaters or furnaces. Gasoli-
ne or gasoline vapors can ignite or
explode, causing severe injury or
property damage.
PERIODIC MAINTENANCE AND ADJUSTMENT
6-39
6

water, diluted mild detergent
with water may be used. Be
sure to rinse off any detergent
residue using plenty of water,
as it is harmful to plastic parts.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
Do not use high-pressure was-
hers or steam-jet cleaners sin-
ce they cause water seepage
and deterioration in the follo-
wing areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or scrat-
ching. Some cleaning com-pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not lea-
ve any marks. If the windshield
is scratched, use a quality
plastic polishing compound
after washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge, and
then rinse thoroughly with clean water.
Use a toothbrush or bottlebrush for
hard-to-reach areas. Stubborn dirt and
insects will come off more easily if the
area is covered with a wet cloth for a few
minutes before cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.
TIP
Salt sprayed on roads in the winter
may remain well into spring.
1. Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
NOTICE: Do not use warm
water since it increases the
corrosive action of the salt.
[ECA10791]
2. Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, surfa-
ces to prevent corrosion.
After cleaning
1. Dry the motorcycle with a cha-
mois or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally indu-
ced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
MOTORCYCLE CARE AND STORAGE
7-2
7

INDEX
AABS (for ABS models)..............................3-12
ABS warning light (for ABS models) ..........3-5
Air filter element and check hose, replacing
and cleaning ..........................................6-15
Anti-theft alarm (optional) ..........................3-9
Auxiliary light bulb, replacing ...................6-34
BBattery......................................................6-29
Brake and clutch levers, checking and
lubricating ..............................................6-25
Brake fluid level, checking .......................6-21
Brake lever ...............................................3-11
Brake pedal ..............................................3-12
Brake pedal, checking and lubricating ....6-26
CCables, checking and lubricating ............6-25
Care............................................................7-1
Catalytic converters .................................3-16
Clutch lever ..............................................3-11
Clutch lever free play, adjusting...............6-20
Coolant.....................................................6-14
Coolant temperature warning light ............3-5
DDimmer switch .........................................3-10
Drive chain slack ......................................6-23
Drive chain, cleaning and lubricating.......6-24
EEngine break-in ..........................................5-3
Engine idling speed, checking .................6-16
Engine oil and oil filter element................6-11
Engine stop switch ..................................3-10
Engine trouble warning light ......................3-5
FFront and rear brake pads, checking ......6-21
Front fork, adjusting .................................3-17
Front fork, checking .................................6-27
Fuel ..........................................................3-14
Fuel consumption, tips for reducing ............5-
Fuel tank breather/overflow hose ............3-15
Fuel tank cap ...........................................3-13
Fuses, replacing .......................................6-31
HHandlebar switches ...................................3-9
Hazard switch ..........................................3-10
Headlight bulb, replacing .........................6-32
High beam indicator light...........................3-4
Horn switch ..............................................3-10
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ..................3-20
Immobilizer system ....................................3-1
Immobilizer system indicator light .............3-6
Indicator and warning lights ......................3-4
LLicense plate light bulb, replacing ...........6-34
MMain switch/steering lock ..........................3-2
Maintenance and lubrication, periodic ......6-4
Maintenance, emission control system .....6-3
Matte color, caution ...................................7-1
Model label ................................................9-1
Multi-function display ................................3-6
NNeutral indicator light.................................3-4
PPanels, removing and installing .................6-8Parking .......................................................5-4
Part locations .............................................2-1
Pass switch ..............................................3-10
RRear suspension, lubricating ...................6-27
SSafety information ......................................1-1
Seat ..........................................................3-16
Shift pedal ................................................3-11
Shifting .......................................................5-2
Shock absorber assembly, adjusting.......3-18
Sidestand .................................................3-19
Sidestand, checking and lubricating .......6-26
Spark plug, checking .................................6-9
Specifications.............................................8-1
Start switch ..............................................3-10
Starting the engine.....................................5-1
Steering, checking ...................................6-28
Storage.......................................................7-3
Supporting the motorcycle ......................6-35
Swingarm pivots, lubricating ...................6-27
TTail/brake light ..........................................6-33
Throttle cable free play, checking ............6-17
Tool kit ........................................................6-1
Troubleshooting .......................................6-38
Troubleshooting charts ............................6-40
Turn signal indicator light ...........................3-4
Turn signal light bulb, replacing ...............6-34
Turn signal switch ....................................3-10
VValve clearance ........................................6-17
Vehicle identification number .....................9-1