check engine YAMAHA XTZ125 2005 User Guide

Page 52 of 97

6-5
6-5
Spark plug12.5 1.25 9.0
Engine oil drain plug20 2.0 14.5
Oil check bolt 7 0.7 5.0
Front wheel axle nut 80 8.0 58
Rear wheel axle nut 80 8.0 58
Use a torque wrench to tighten these items. It is
recommended that these items be checked occasionally,
specially before a long trip. Always check the tightness of
these items whenever they are loosened for any reason.
A
(Nut)
10 mm
12 mm
14 mm
17 mm
19 mm
22 mmB
(Bolt)
6 mm
8 mm
10 mm
12 mm
14 mm
16 mmGeneral torque especifications
Nm
6
15
30
55
85
130kgf.m
0,6
1,5
3,0
5,5
8,5
13,0lbf. ft
4,3
11
22
40
61
94 Torque specifications
Torque
Nm
kgfm Item
Nm
Spark plug12.5 1.25 9.0
Engine oil drain plug20 2.0 14.5
Oil check bolt 7 0.7 5.0
Front wheel axle nut 80 8.0 58
Rear wheel axle nut 80 8.0 58
Use a torque wrench to tighten these items. It is
recommended that these items be checked occasionally,
specially before a long trip. Always check the tightness of
these items whenever they are loosened for any reason.
A
(Nut)
10 mm
12 mm
14 mm
17 mm
19 mm
22 mmB
(Bolt)
6 mm
8 mm
10 mm
12 mm
14 mm
16 mmGeneral torque especifications
Nm
6
15
30
55
85
130kgf.m
0,6
1,5
3,0
5,5
8,5
13,0lbf. ft
4,3
11
22
40
61
94 Torque specifications
Torque
Nm
kgfm Item
Nm

Page 53 of 97

6-6
6-6




  
1. Oil level measurement
a. Place the motorcycle on a level place and hold it in an
upright position. Warm up the engine for several
minutes.
NOTE:
Be sure the motorcycle is positioned straight up when
checking the oil level. A slight tilt toward the side can result
in false readings.
b. With the engine stopped, with the engine stopped,
unscrew the oil filler cap/ dispstick and rest it on the
threads of the ok.
NOTE:
Wait a few minutes until the oil level settles before checking.
c. remove the oil filler cap/ dispstick, clean it with a dry
cloth and check the oil level.
NOTE:
To check the oil level the oil filler cap/ dispstick can not be
screwed, just lightly seated in place.
d. The oil level should be between the maximum and
minimum marks. If the level is low, add oil to raise it to
the indicated level, check for oil leakage. Engine oil




  
1. Oil level measurement
a. Place the motorcycle on a level place and hold it in an
upright position. Warm up the engine for several
minutes.
NOTE:
Be sure the motorcycle is positioned straight up when
checking the oil level. A slight tilt toward the side can result
in false readings.
b. With the engine stopped, with the engine stopped,
unscrew the oil filler cap/ dispstick and rest it on the
threads of the ok.
NOTE:
Wait a few minutes until the oil level settles before checking.
c. remove the oil filler cap/ dispstick, clean it with a dry
cloth and check the oil level.
NOTE:
To check the oil level the oil filler cap/ dispstick can not be
screwed, just lightly seated in place.
d. The oil level should be between the maximum and
minimum marks. If the level is low, add oil to raise it to
the indicated level, check for oil leakage. Engine oil

Page 54 of 97

6-7
6-7
a. Warm up the engine for a few minutes.
b. Stop the engine. Place an oil pan under the engine and
remove the dipstick.
c. Remove the drain plug and drain the oil.
d. Reinstall the drain plug, check if the gasket is damaged
and lighten it to the specified torque.
 


 
2. Engine oil and filter replacement
Tightening torque:
Drain plug:
20 N.m (2.0 kgf.m, 14.5 lbf.t)
a. Warm up the engine for a few minutes.
b. Stop the engine. Place an oil pan under the engine and
remove the dipstick.
c. Remove the drain plug and drain the oil.
d. Reinstall the drain plug, check if the gasket is damaged
and lighten it to the specified torque.
 


 
2. Engine oil and filter replacement
Tightening torque:
Drain plug:
20 N.m (2.0 kgf.m, 14.5 lbf.t)

Page 55 of 97

6-8
6-8 e.Fill engine with oil. Install the oil filter cap and tighten.
NOTE:
Recommended engine oil classification; API Service “SH”
type or equivalent
Recommended oil:
YAMALUBE 4
Oil quantity:
Total amount:
1.2 L ( 0.264 Imp gal, 0.317 US gal)
Periodic oil change:
1.0 L ( 0.220 Imp gal, 0.264 US gal)
f. Start the engine and warm up for a few minutes. While
warming up, check for oil leakage. If oil leakage is found,
stop the engine immediately, and check for the cause.
g. Stop the engine and check the oil level.
CAUTION:
Be sure no foreign material enters the crankcase.
CAUTION:
Do not put in any chemical additives. Engine oil also
lubricates the clutch and additives could cause clutch
slippage.
After replacing the engine oil, be sure to check the oil
pressure.
CAUTION:
e.Fill engine with oil. Install the oil filter cap and tighten.
NOTE:
Recommended engine oil classification; API Service “SH”
type or equivalent
Recommended oil:
YAMALUBE 4
Oil quantity:
Total amount:
1.2 L ( 0.264 Imp gal, 0.317 US gal)
Periodic oil change:
1.0 L ( 0.220 Imp gal, 0.264 US gal)
f. Start the engine and warm up for a few minutes. While
warming up, check for oil leakage. If oil leakage is found,
stop the engine immediately, and check for the cause.
g. Stop the engine and check the oil level.
CAUTION:
Be sure no foreign material enters the crankcase.
CAUTION:
Do not put in any chemical additives. Engine oil also
lubricates the clutch and additives could cause clutch
slippage.
After replacing the engine oil, be sure to check the oil
pressure.
CAUTION:

Page 56 of 97

6-9
6-9
Oil pressure1. Remove the check bolt 1 in the cylinder head.
2. Start the engine and keep it idling until oil flows out of
the bleed hole. If no oil comes out after one minute,
turn off the engine immediately so it will not seize. In
such a case go to the nearest Yamaha dealer or other
qualified mechanic for repairs.
3. After checking, tighten the check bolt to the specified
torque.
Check bolt torque:
7 N.m (0.7 Kgf.m, 5.0 lbf.ft)


Oil pressure1. Remove the check bolt 1 in the cylinder head.
2. Start the engine and keep it idling until oil flows out of
the bleed hole. If no oil comes out after one minute,
turn off the engine immediately so it will not seize. In
such a case go to the nearest Yamaha dealer or other
qualified mechanic for repairs.
3. After checking, tighten the check bolt to the specified
torque.
Check bolt torque:
7 N.m (0.7 Kgf.m, 5.0 lbf.ft)



Page 61 of 97

6-14
6-14
NOTE:
Before checking the throttle cable free play, the engine
idling speed should be adjusted.
Free play:
3 ~ 5 mm (0.12 ~ 0.19 in) Throttle cable adjustment
The throttle cable should have an specified free play in the
turning direction at the grip flange. If the free play is incorrect,
#

$
NOTE:
Before checking the throttle cable free play, the engine
idling speed should be adjusted.
Free play:
3 ~ 5 mm (0.12 ~ 0.19 in) Throttle cable adjustment
The throttle cable should have an specified free play in the
turning direction at the grip flange. If the free play is incorrect,
#

$

Page 72 of 97

6-25
6-25
CAUTION:
Too little chain slack will overload the engine and other
vital parts. Keep the slack within the specified limits.
Axle nut torque:
80 N.m (8.0 Kgf.m, 58 lbf.ft)
5. Adjust the free play in the brake pedal.
CAUTION:
Check the operation of the brake light after adjusting
the rear brake.1. Loosen the rear brake adjuster.
2. Loosen the axle nut.
3. Turn both left and right chain puller the same
amount.Make sure that they are in the same position
for proper wheel alignment. Drive chain slack adjustment
!&
  
 .!
 
4. After adjusting, be sure to tighten the axle nut.
CAUTION:
Too little chain slack will overload the engine and other
vital parts. Keep the slack within the specified limits.
Axle nut torque:
80 N.m (8.0 Kgf.m, 58 lbf.ft)
5. Adjust the free play in the brake pedal.
CAUTION:
Check the operation of the brake light after adjusting
the rear brake.1. Loosen the rear brake adjuster.
2. Loosen the axle nut.
3. Turn both left and right chain puller the same
amount.Make sure that they are in the same position
for proper wheel alignment. Drive chain slack adjustment
!&
  
 .!
 
4. After adjusting, be sure to tighten the axle nut.

Page 75 of 97

6-28
6-28
Rear suspensionSidestand
Lubricate the pivoting parts. Check to see that the sidestand
moves up and down smoothly.
RECOMMENDED LUBRICANT:
Engine oil SAE 20W50
If the sidestand does not move smoothly, consult a
Yamaha dealer.
Lubricate the rear suspension through the nipple.
RECOMMENDED LUBRICANT:
Molybdenum dissulfide grease
0
1


WARNING:
Rear suspensionSidestand
Lubricate the pivoting parts. Check to see that the sidestand
moves up and down smoothly.
RECOMMENDED LUBRICANT:
Engine oil SAE 20W50
If the sidestand does not move smoothly, consult a
Yamaha dealer.
Lubricate the rear suspension through the nipple.
RECOMMENDED LUBRICANT:
Molybdenum dissulfide grease
0
1


WARNING:

Page 89 of 97

6-42
6-42 Troubleshooting chart
ADVERTENC
Never check the fuel system while smoking or in the
vicinity of an open flame.
WARNING:
Check if there is
fuel in the fuel tank
Use electric
starter
Remove spark plug
and check
electrode
Use electric starter 1. Fuel
2. Compression
3. Ignition
4. Battery *Enough fuel
No fuel
There is compression
No compression
Wet
Dry
Engine turns
over quickly
Engine turns
over slowlySupply fuel
Go to ignition check
Ask Yamaha dealer to inspect
Wipe clean with dry cloth and correct
spark plug gap or replace spark plugs
Ask Yamaha dealer to inspect
Battery good
Check fluid, recharge
and check
connections
Go to compression
check
Engine doesn’t start, go to
compression check
Open the throttle hal-way
and start the engine
Engine doesn’t start, ask
Yamaha dealer to inspect.Engine doesn’t start,
go to battery check
* Obs.: XTZ 125E
Troubleshooting chart
ADVERTENC
Never check the fuel system while smoking or in the
vicinity of an open flame.
WARNING:
Check if there is
fuel in the fuel tank
Use electric
starter
Remove spark plug
and check
electrode
Use electric starter 1. Fuel
2. Compression
3. Ignition
4. Battery *Enough fuel
No fuel
There is compression
No compression
Wet
Dry
Engine turns
over quickly
Engine turns
over slowlySupply fuel
Go to ignition check
Ask Yamaha dealer to inspect
Wipe clean with dry cloth and correct
spark plug gap or replace spark plugs
Ask Yamaha dealer to inspect
Battery good
Check fluid, recharge
and check
connections
Go to compression
check
Engine doesn’t start, go to
compression check
Open the throttle hal-way
and start the engine
Engine doesn’t start, ask
Yamaha dealer to inspect.Engine doesn’t start,
go to battery check
* Obs.: XTZ 125E

Page:   < prev 1-10 11-20