lock YAMAHA XVS1100A 2003 User Guide

PERIODIC MAINTENANCE AND MINOR REPAIR
6-17
6
EAU00696
Adjusting the brake lever free
play The brake lever free play should mea-
sure 5–8 mm as shown. Periodically
check the brake lever free play and, if
necessary, adjust it as follows.1. Loosen the locknut at the brake le-
ver.
2. To increase the brake lever free
play, turn the adjusting bolt in di-
rection
a. To decrease the brake
lever free play, turn the adjusting
bolt in direction
b.
3. Tighten the locknut.
EW000099
WARNING
@

After adjusting the brake lever
free play, check the free play
and make sure that the brake is
working properly.


A soft or spongy feeling in the
brake lever can indicate the
presence of air in the hydraulic
system. If there is air in the hy-
draulic system, have a Yamaha
dealer bleed the system before
operating the motorcycle. Air in
the hydraulic system will dimin-
ish the braking performance,
which may result in loss of con-
trol and an accident.
@
a. Brake lever free play
1. Locknut
2. Brake lever free play adjusting bolt
U5KSE4.book Page 17 Wednesday, September 11, 2002 11:55 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-20
6 Observe these precautions:


When checking the fluid level,
make sure that the top of the brake
fluid reservoir is level.


Use only the recommended quali-
ty brake fluid, otherwise the rubber
seals may deteriorate, causing
leakage and poor braking perfor-
mance.


Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performance.


Be careful that water does not en-
ter the brake fluid reservoir when
refilling. Water will significantly
lower the boiling point of the fluid
and may result in vapor lock.


Brake fluid may deteriorate paint-
ed surfaces or plastic parts. Al-
ways clean up spilled fluid
immediately.


As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if the
brake fluid level goes down sud-
denly, have a Yamaha dealer
check the cause.
EAU03976
Changing the brake fluid Have a Yamaha dealer change the
brake fluid at the intervals specified in
the NOTE after the periodic mainte-
nance and lubrication chart. In addition,
have the oil seals of the master cylin-
ders and calipers as well as the brake
hoses replaced at the intervals listed
below or whenever they are damaged
or leaking.

Oil seals: Replace every two
years.


Brake hoses: Replace every four
years.
1. Brake fluid reservoir
2. Minimum level mark
Recommended brake fluid: DOT 4Rear
U5KSE4.book Page 20 Wednesday, September 11, 2002 11:55 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-30
6 3. Remove the headlight bulb holder
by turning it counterclockwise, and
then remove the defective bulb.
EW000119
WARNING
_ Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down. _4. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
EC000105
CAUTION:_ Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,
and the bulb life will be adversely af-
fected. Thoroughly clean off any dirt
and fingerprints on the headlight
bulb using a cloth moistened with
alcohol or thinner. _5. Install the headlight bulb cover,
and then connect the coupler.
6. Install the headlight unit by install-
ing the screws.7. Have a Yamaha dealer adjust the
headlight beam if necessary.
1. Headlight bulb holder
1. Do not touch the glass part of the bulb.
U5KSE4.book Page 30 Wednesday, September 11, 2002 11:55 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-31
6
EAU00855
Replacing a turn signal light
bulb or the tail/brake light
bulb 1. Remove the lens by removing the
screws.
2. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
EC000108
CAUTION:@ Do not overtighten the screws, oth-
erwise the lens may break. @
EAU01579
Supporting the motorcycle Since this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other mainte-
nance requiring the motorcycle to
stand upright. Check that the motor-
cycle is in a stable and level position
before starting any maintenance. A
strong wooden box can be placed un-
der the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcycle
by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack un-
der the frame in front of the rear
wheel.
2. Raise the front wheel off the
ground by using a motorcycle
stand.
1. Screw (× 2)
1. Screw (× 3)
U5KSE4.book Page 31 Wednesday, September 11, 2002 11:55 AM

10-INDEXAAir filter element, cleaning ...................... 6-11
Anti-theft alarm (optional) .........................3-6BBattery ................................................... 6-25
Brake and clutch levers,
checking and lubricating ...................... 6-22
Brake and shift pedals,
checking and lubricating ...................... 6-21
Brake fluid, changing ............................. 6-20
Brake fluid level, checking...................... 6-19
Brake lever...............................................3-9
Brake lever free play, adjusting .............. 6-17
Brake light switch, adjusting ................... 6-18
Brake pads, checking............................. 6-19
Brake pedal..............................................3-9
Brake pedal position, adjusting .............. 6-18CCables, checking and lubricating............ 6-21
Carburetors, adjusting............................ 6-12
Care.........................................................7-1
Clutch lever ..............................................3-8
Clutch lever free play, adjusting ............. 6-16
Conversion table ......................................8-5DDimmer switch .........................................3-7EEngine break-in........................................5-5
Engine idling speed................................ 6-12
Engine oil .................................................6-7
Engine stop switch ...................................3-7
Engine trouble warning light .................... 3-4FFinal gear oil ............................................ 6-9
Front fork, checking ............................... 6-23
Fuel ....................................................... 3-10
Fuel cock ............................................... 3-11
Fuel consumption, tips for reducing ......... 5-4
Fuel tank cap ........................................... 3-9
Fuses, replacing .................................... 6-27HHandlebar switches ................................. 3-7
Hazard switch .......................................... 3-8
Headlight bulb, replacing ....................... 6-29
Helmet holder ........................................ 3-14
High beam indicator light ......................... 3-5
Horn switch ............................................. 3-7IIdentification numbers ............................. 9-1
Ignition circuit cut-off system.................. 3-19
Immobilizer system .................................. 3-1
Immobilizer system indicator light ............ 3-5
Indicator and warning lights ..................... 3-4KKey identification number ........................ 9-1LLuggage strap holders ........................... 3-18MMain switch/steering lock ......................... 3-2
Model label .............................................. 9-2
NNeutral indicator light ...............................3-4OOil level warning light ...............................3-4PPanel, removing and installing..................6-5
Parking.....................................................5-5
Part locations ...........................................2-1
Pass switch ..............................................3-7
Periodic maintenance and
lubrication chart .....................................6-2
Pre-operation check list ............................4-1SSafety information ....................................1-1
Seats .....................................................3-13
Passenger seat.................................3-13
Rider seat .........................................3-13
Shifting .....................................................5-3
Shift pedal ................................................3-8
Shift points (for Switzerland only) .............5-4
Shock absorber assembly, adjusting ......3-16
Sidestand ...............................................3-19
Sidestand, checking and lubricating .......6-22
Spark plugs, checking ..............................6-6
Specifications ...........................................8-1
Speedometer unit.....................................3-6
Starter (choke) lever...............................3-12
Starting a cold engine ..............................5-1
Starting a warm engine ............................5-3
Start switch ..............................................3-8
Steering, checking..................................6-23
U5KSE4.book Page 1 Wednesday, September 11, 2002 11:55 AM