light YAMAHA XVS1100A 2003 Owner's Manual

PERIODIC MAINTENANCE AND MINOR REPAIR
6-18
6
EAU01746
Adjusting the brake pedal
position The top of the brake pedal should be
positioned approximately 98.5 mm
above the top of the footrest as shown.
Periodically check the brake pedal po-
sition and, if necessary, have a
Yamaha dealer adjust it.
EW000109
WARNING
@ A soft or spongy feeling in the brake
pedal can indicate the presence of
air in the hydraulic system. If there
is air in the hydraulic system, have a
Yamaha dealer bleed the system be-
fore operating the motorcycle. Air in
the hydraulic system will diminish
the braking performance, which
may result in loss of control and an
accident. @
EAU00713
Adjusting the rear brake light
switch The rear brake light switch, which is ac-
tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, adjust the brake light switch
as follows.
Turn the adjusting nut while holding the
rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction
a. To
make the brake light come on later,
turn the adjusting nut in direction
b.
a. Distance between brake pedal and footrest
1. Rear brake light switch
2. Rear brake light switch adjusting nut
U5KSE4.book Page 18 Wednesday, September 11, 2002 11:55 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-27
6
EAU04993
Replacing the fuses The main fuse is located under the igni-
tor unit panel.The fuse box, which contains the fuses
for the individual circuits, is located in-
side the storage compartment. (See
page 3-15 for storage compartment
cover removal and installation proce-
dures.)
If a fuse is blown, replace it as follows.
NOTE:_ Include steps 1–3 and 9–10 only for the
main fuse. _1. Remove the rider seat. (See page
3-13 for rider seat removal and in-
stallation procedures.)
2. Remove the quick fasteners
shown by pushing the center in
with a screwdriver, then pulling the
fastener out.
1. Fuse box
2. Headlight fuse
3. Signaling system fuse
4. Ignition fuse
5. Carburetor heater fuse
6. Ignitor unit fuse
7. Odometer and immobilizer system fuse
(backup fuse)
8. Spare fuse (× 3)
9. Turn signal light, taillight, auxiliary light and
hazard fuse
1. Quick fastener (× 3)
U5KSE4.book Page 27 Wednesday, September 11, 2002 11:55 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-28
6 3. Pull the ignitor unit panel outward
to the right.
4. Turn the key to “OFF” and turn off
the electrical circuit in question.
5. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
EC000103
CAUTION:_ Do not use a fuse of a higher amper-
age rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire. _
6. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
7. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
8. Install the storage compartment
cover.
1. Ignitor unit panel
2. Spare main fuse
3. Main fuse
Specified fuses:
Main fuse: 30 A
Odometer and
immobilizer system fuse
(backup fuse): 10 A
Ignition fuse: 10 A
Headlight fuse: 15 A
Carburetor heater fuse: 15 A
Signaling system fuse: 10 A
Ignitor unit fuse: 5 A
Turn signal light, taillight,
auxiliary light and
hazard fuse: 10 A
U5KSE4.book Page 28 Wednesday, September 11, 2002 11:55 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-29
69. Place the ignitor unit panel in the
original position and install the
quick fasteners.
NOTE:_ To install a quick fastener, push its pin
back so that it will protrude from the
fastener head, then insert the fastener
and push the protruding pin in until it is
flush with the fastener head. _10. Install the rider seat.
EAU04187
Replacing the headlight bulb This motorcycle is equipped with a
quartz bulb headlight. If the headlight
bulb burns out, replace it as follows.
1. Remove the headlight unit by re-
moving the screws.2. Disconnect the headlight coupler,
and then remove the bulb cover.
1. Quick fastener
2. Pin
After removal
Before installation
1. Screw (× 2)
1. Headlight bulb cover
2. Headlight coupler
U5KSE4.book Page 29 Wednesday, September 11, 2002 11:55 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-30
6 3. Remove the headlight bulb holder
by turning it counterclockwise, and
then remove the defective bulb.
EW000119
WARNING
_ Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down. _4. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
EC000105
CAUTION:_ Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,
and the bulb life will be adversely af-
fected. Thoroughly clean off any dirt
and fingerprints on the headlight
bulb using a cloth moistened with
alcohol or thinner. _5. Install the headlight bulb cover,
and then connect the coupler.
6. Install the headlight unit by install-
ing the screws.7. Have a Yamaha dealer adjust the
headlight beam if necessary.
1. Headlight bulb holder
1. Do not touch the glass part of the bulb.
U5KSE4.book Page 30 Wednesday, September 11, 2002 11:55 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-31
6
EAU00855
Replacing a turn signal light
bulb or the tail/brake light
bulb 1. Remove the lens by removing the
screws.
2. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
EC000108
CAUTION:@ Do not overtighten the screws, oth-
erwise the lens may break. @
EAU01579
Supporting the motorcycle Since this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other mainte-
nance requiring the motorcycle to
stand upright. Check that the motor-
cycle is in a stable and level position
before starting any maintenance. A
strong wooden box can be placed un-
der the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcycle
by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack un-
der the frame in front of the rear
wheel.
2. Raise the front wheel off the
ground by using a motorcycle
stand.
1. Screw (× 2)
1. Screw (× 3)
U5KSE4.book Page 31 Wednesday, September 11, 2002 11:55 AM

MOTORCYCLE CARE AND STORAGE
7-2
7 thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.


Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments, switch-
es and lights), breather hoses
and vents.


For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the wind-shield is scratched, use a quali-
ty plastic polishing compound
after washing.
_
After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.NOTE:_ Salt sprayed on roads in the winter may
remain well into spring. _
U5KSE4.book Page 2 Wednesday, September 11, 2002 11:55 AM

SPECIFICATIONS
8-3
8
Tire air pressure (measured
on cold tires)
Up to 90 kg*
Front 225 kPa (2.25 kgf/cm
2, 2.25 bar)
Rear 225 kPa (2.25 kgf/cm2, 2.25 bar)
90 kg–maximum*
Front 225 kPa (2.25 kgf/cm2, 2.25 bar)
Rear 250 kPa (2.50 kgf/cm2, 2.50 bar)
* Total weight of rider, passenger, cargo and accessories
Wheels
Front
Type Spoke wheel
Size 16 M/C × MT 3.00
Rear
Type Spoke wheel
Size 15 M/C × MT 4.50
Brakes
Front
Type Dual disc brake
Operation Right hand
Fluid DOT 4
Rear
Type Single disc brake
Operation Right foot
Fluid DOT 4Suspension
Front Telescopic fork
Rear Swingarm (link suspension)
Spring/shock absorber
Front Coil spring / oil damper
Rear Coil spring / gas-oil damper
Wheel travel
Front 140 mm
Rear 113 mm
Electrical system
Ignition system T.C.I. (digital)
Charging system
Type A.C. magneto
Standard output 14 V, 305 W@ 5,000 r/min
Battery
Model GT14B-4
Voltage, capacity 12 V, 12 Ah
Headlight typeHalogen bulb
U5KSE4.book Page 3 Wednesday, September 11, 2002 11:55 AM

SPECIFICATIONS
8-4
8
Bulb voltage, wattage × quantity
Headlight 12 V, 60/55 W × 1
Auxiliary light 12 V, 4 W × 1
Tail/brake light 12 V, 5/21 W × 1
Turn signal light 12 V, 21 W × 4
Meter lighting 14 V, 1.4 W × 2
Oil level warning light 12 V, 1.7 W × 1
Neutral indicator light 12 V, 1.7 W × 1
Turn signal indicator light 12 V, 1.7 W × 1
Engine trouble warning light 12 V, 1.7 W × 1
High beam indicator light 12 V, 1.7 W × 1
Fuses
Main fuse 30 A
Signaling system fuse 10 A
Odometer and immobilizer
system fuse (backup fuse) 10 A
Ignition fuse 10 A
Headlight fuse 15 A
Carburetor heater fuse 15 A
Ignitor unit fuse 5 A
Turn signal light, taillight,
auxiliary light and hazard fuse 10 A
U5KSE4.book Page 4 Wednesday, September 11, 2002 11:55 AM

10-INDEXAAir filter element, cleaning ...................... 6-11
Anti-theft alarm (optional) .........................3-6BBattery ................................................... 6-25
Brake and clutch levers,
checking and lubricating ...................... 6-22
Brake and shift pedals,
checking and lubricating ...................... 6-21
Brake fluid, changing ............................. 6-20
Brake fluid level, checking...................... 6-19
Brake lever...............................................3-9
Brake lever free play, adjusting .............. 6-17
Brake light switch, adjusting ................... 6-18
Brake pads, checking............................. 6-19
Brake pedal..............................................3-9
Brake pedal position, adjusting .............. 6-18CCables, checking and lubricating............ 6-21
Carburetors, adjusting............................ 6-12
Care.........................................................7-1
Clutch lever ..............................................3-8
Clutch lever free play, adjusting ............. 6-16
Conversion table ......................................8-5DDimmer switch .........................................3-7EEngine break-in........................................5-5
Engine idling speed................................ 6-12
Engine oil .................................................6-7
Engine stop switch ...................................3-7
Engine trouble warning light .................... 3-4FFinal gear oil ............................................ 6-9
Front fork, checking ............................... 6-23
Fuel ....................................................... 3-10
Fuel cock ............................................... 3-11
Fuel consumption, tips for reducing ......... 5-4
Fuel tank cap ........................................... 3-9
Fuses, replacing .................................... 6-27HHandlebar switches ................................. 3-7
Hazard switch .......................................... 3-8
Headlight bulb, replacing ....................... 6-29
Helmet holder ........................................ 3-14
High beam indicator light ......................... 3-5
Horn switch ............................................. 3-7IIdentification numbers ............................. 9-1
Ignition circuit cut-off system.................. 3-19
Immobilizer system .................................. 3-1
Immobilizer system indicator light ............ 3-5
Indicator and warning lights ..................... 3-4KKey identification number ........................ 9-1LLuggage strap holders ........................... 3-18MMain switch/steering lock ......................... 3-2
Model label .............................................. 9-2
NNeutral indicator light ...............................3-4OOil level warning light ...............................3-4PPanel, removing and installing..................6-5
Parking.....................................................5-5
Part locations ...........................................2-1
Pass switch ..............................................3-7
Periodic maintenance and
lubrication chart .....................................6-2
Pre-operation check list ............................4-1SSafety information ....................................1-1
Seats .....................................................3-13
Passenger seat.................................3-13
Rider seat .........................................3-13
Shifting .....................................................5-3
Shift pedal ................................................3-8
Shift points (for Switzerland only) .............5-4
Shock absorber assembly, adjusting ......3-16
Sidestand ...............................................3-19
Sidestand, checking and lubricating .......6-22
Spark plugs, checking ..............................6-6
Specifications ...........................................8-1
Speedometer unit.....................................3-6
Starter (choke) lever...............................3-12
Starting a cold engine ..............................5-1
Starting a warm engine ............................5-3
Start switch ..............................................3-8
Steering, checking..................................6-23
U5KSE4.book Page 1 Wednesday, September 11, 2002 11:55 AM